Home » Canon » Printers » Canon PIXMA MX892

Canon PIXMA MX892 Support Question

Find answers below for this question about Canon PIXMA MX892.
Need a Canon PIXMA MX892 manual? We have 11 online manuals for this item!

Canon Overview Questions Manuals Reviews Videos Research

Question posted by Anonymous-132502 on March 12th, 2014

Printer Has No Power

I was printing 3 documents. The first document printed fine, then the printer shut off. It has no lights on. Pushing the on button (or any other button) gets no response. I have tried unplugging it for 5 minutes then plugging it back in. I have switched power outlets. I have checked the power cord connection to the printer. I don't know what else to try. Is there some type of fuse somewhere?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TommyKervz on March 12th, 2014 1:57 PM

This answer was accepted by the poster of the original question.

TommyKervz

Member since:
January 10th, 2013

Points: 17,776,813

1,100
points

Hi. Try to

1. Unplug it and leave so for an hour and re-try it afterwards

2. Replace the Ac adapter (which may most likely have failed)

3. The PCB (Printed Circuite Board) may be the one with a failed component on the other hand.

Hope that is helpful.
Kervz at www.satechhelp.co.za

Related Canon PIXMA MX892 Manual Pages

Guide for Printer Setup for Network - Page 1

... Guide This guide provides information for setting up a network connection for Connection Cable Connection Printer Setup Character Entry Troubleshooting Network Connection Wireless Connection Preparation for Connection Printer Setup Setup Procedure Selection Push Button Method Standard setup WPS Other setup (Advanced setup) Disable WEP WPA/WPA2 Wired Connection Preparation for the printer.

Guide for Printer Setup for Network - Page 2

... protocol for Connection Before Starting Wireless Connection Setup 1. For details, refer to the manual of the mode buttons (A) will be used over a wireless connection without an access point, is turned on the printer. If the power is set to the "IEEE802.11 n only" mode, WEP or TKIP cannot be used as your system...

Guide for Printer Setup for Network - Page 3

... or router supports this technology, press the Stop button and choose Standard setup. c Setup Procedure Selection The printer will automatically search for access points supporting WPS (Wi-Fi Protected Setup). If the Push Button Method screen is enabled. Press the OK button (B). 2. The (blue) Wi-Fi lamp (C) lights up when wireless connection is displayed on the...

Guide for Printer Setup for Network - Page 4

... connecting to the access point manual. 2. d-A Push Button Method d Connection Using WPS 1. For details on the printer ﬂashes while searching for about 5 seconds). The (blue) Wi-Fi lamp on pressing the WPS button, refer to the access point. 3. Press and hold the WPS button on the printer within 2 minutes. When the left screen appears, press the...

Guide for Printer Setup for Network - Page 5

Press the left screen appears, press the OK button. Press the left Function button. 10.When the left Function button. 8. The network connection setup is case-sensitive. 9. Press the OK button. 6. Character entry is now complete. Select your access point or router into the printer. 7. Enter the network password (WEP key or passphrase) of the screens...

Guide for Printer Setup for Network - Page 6

... the left screen appears, press the OK button. Select Push button method. 4. Select WPS. 2. For details on the printer ﬂashes while searching for about 5 seconds). The (blue) Wi-Fi lamp on pressing the WPS button, refer to the access point. 8. Press and hold the WPS button on the printer within 2 minutes. The network connection setup is now...

Guide for Printer Setup for Network - Page 10

If the power is turned on the right side at the same time. • When using a router, connect the printer and computer to the LAN side (same network segment).... will be used over wireless and wired connections at the back of the mode buttons (A) will need an Ethernet cable (sold separately). 1. Connect the printer and a network device (router, etc.) with security measures, as there is...

Guide for Printer Setup for Network - Page 11

Select Device settings. 5. Select Change wireless/wired. 9. Press the MENU button (A) on the printer. 2. c Printer Setup 1. Press the OK button. 6. Press the OK button. 8. Press the OK button. Press the OK button (B). 4. Select LAN settings. 7. Press the OK button. 10.Select Wired LAN active. 11. Use the buttons (A) to select the Setup icon. 3.

Guide for Printer Setup for Network - Page 13

... Entered characters appear in the upper section (C) of the on -screen keyboard, then press the OK button to enter it. Follow the procedure below. 1. Character Entry You can enter the characters when the... above is displayed, press the center Function button (A) to switch to a keyboard that supports characters you want to use. When an on the printer. Repeat 1 and 2 to enter more characters.

Guide for Printer Setup for Network - Page 14

... exist. Do you have only one AccessPoint only, then press the OK button. After checking the above points, press the left Function button on the displayed screen, then press the OK button. Wireless connection settings of the target access point on the printer to the manual supplied with the same name are possible? •...

Guide for Printer Setup for Network - Page 16

...to use WEP key number 1, or select a WEP key number by entering wireless connection settings of the printer directly. If using WEP key number 2, 3 or 4 of the access point, set to something other... Select Device settings, then press the OK button. 4. If the problem is set to check the MAC address of the printer. 1. Check the access point settings and try again. For details on how to check ...

Guide for Printer Setup for Network - Page 17

... settings so that the MAC address of the printer will be accepted. Select LAN settings > Conﬁrm LAN settings > WLAN setting list to check the MAC address of the printer. 1. Follow the procedure below to check MAC address. Press the MENU button (A). 2. Use the buttons (B) to select Wireless LAN setup, then press the...

Guide for Printer Setup for Network - Page 19

...turn it off the access point, turn it back on, then press the left Function button (A) on the printer to search for the access point, refer to the manual supplied with the access point or...connection via "ANY" SSID, etc.) or disable the stealth mode, then press the left Function button on the printer to search for the access point again. Select Directly enter the access point name in IEEE802....

Guide for Printer Setup for Network - Page 20

... how to change the communication standard to the access point. Select Device settings, then press the OK button. 4. Select LAN settings > Conﬁrm LAN settings > WLAN setting list to TKIP, IEEE802.... standard to something other than TKIP or change the settings of the printer. 1. Check the access point settings and try again. See also the sections below: If the access point is con...

Guide for Printer Setup for Network - Page 21

... point or contact its manufacturer. If using WEP key number 2, 3 or 4 of the printer directly. Select Setup, then press the OK button. 3. Follow the procedure below : If the DHCP function of the printer. 1. Check the access point settings and try again. Make sure that the WEP key entered for the access point is inactive...

Guide for Printer Setup for Network - Page 22

... the IP address (IPv4 only) of the printer and conﬁgure wireless connection settings again. Select Other setup, then press the OK button. 6. Select IP address, then press the OK button. 10. Select Device settings, then press the OK button. 4. Select Yes, then press the OK button. 9. In addition, make sure that the selected...

MX890 series Specifications - Page 1

...: Approx. 1 minute/page at 33.6...to 95 % RH (no condensation) Power supply AC 100-240 V, 50/60 Hz Power consumption Printing (Copy): Approx. 23 W Standby ...push button method is required to Windows 7, then install the bundled software again. • Windows: Some functions may be placed with the Canon inkjet printer...FINE Cartridges) are a theoretical maximum transmission speed between the printer...

MX890 series Especificaciones [Spanish Version] - Page 1

... 1 minute/page at...Push button configuration/PIN code method) Other Features: Administration password QT5-4930-V01 XXXXXXXX ©CANON INC.2012 Minimum System Requirements Conform to PC *2 The wait time for printing... (no condensation) Power supply AC 100-240 V, 50/60 Hz Power consumption Printing (Copy): Approx....FINE Cartridges) are a theoretical maximum transmission speed between the printer...

Setup Guide - Page 11

Step 2 Press the FAX button. Previous Next 11 Step 1 Turn on the MX892 by pressing the ON button if the machine is not powered on already.

Setup Guide - Page 20

Step 1 Turn on the MX892 by pressing the ON button if the machine is not powered on already. Step 2 Press the FAX button. Previous Next 20