Bose VCS-10 Support Question
Bose VCS-10 Support Question
Find answers below for this question about Bose VCS-10.Need a Bose VCS-10 manual? We have 1 online manual for this item!
Question posted by bipolarbearaintit on May 18th, 2016
Codes For A Bose Cinemate 15
what are the codes for Dish Network and how do you use it to enter the codes
Current Answers
Answer #1: Posted by TheWiz on May 19th, 2016 6:00 AM
TheWiz
Member since:
October 13th, 2011 Points: 25,383,424
Member since:
October 13th, 2011 Points: 25,383,424
Related Bose VCS-10 Manual Pages
Owner's guide - Page 3
...speaker 6 Position your surround speakers 7 Connect the speakers 8 Choosing speaker cord 8 Be sure to use the cord properly 8 Make the connections 9 Check the connections 10 Mounting your speakers on the back of each speaker... 14 Troubleshooting 14 Customer service 14 Cleaning speakers 15 Warranty period 15 Technical information 15
For your records
Serial numbers are located on...
Owner's guide - Page 4
... owner's guide.
4 Both the VCS-10® center speaker and the VCS-30® Series II center/surround speaker system are designed for choosing Bose® home theater speakers. Please read and follow the instructions in the original carton and notify Bose or your authorized Bose dealer immediately. Instead, repack all packing materials for use with five amplifi...
Owner's guide - Page 5
The VCS-30® Series II system carton contents
Left surround speaker
Right surround speaker
Mounting brackets
Rubber feet
Center speaker
Mounting hardware Owner's guide
5 English
Figure 1
A. The VCS-10® speaker carton contents
Center speaker Rubber feet
Setting Up
Owner's guide
B.
Owner's guide - Page 6
CAUTION: The VCS-10® speaker is not designed to be set on end in a vertical position, mounted on top of its performance.
Use additional rubber feet as needed , for placing the center speaker
Figure 3
Adding optional self-adhesive feet to fall on , above , to the bottom of the center speaker
Pre-attached feet (2 of 6)
Optional self...
Owner's guide - Page 7
... 4 Alternate choices for tightening the bracket screw.
7 English
Setting Up
Position your surround speakers
Surround speakers in the VCS-30® Series II speaker system provide surround sound effects from the rear of your room allows.
• To mount the speakers on brackets, be sure to leave room between the end of the bracket and...
Owner's guide - Page 8
.... Not doing so may want to your authorized Bose dealer. CAUTION: Never use broken or frayed wiring, which can result in ...code requirements and safety regulations. At the ends of two insulated wires. Note: It is marked (striped, collared, or ribbed).
The insulation around one wire is sometimes difficult to use the proper gauge (thickness) of ±0.5dB.
Choosing speaker...
Owner's guide - Page 9
...;er (Figure 7). Connect one terminal lever and insert the appropriate wire (Figure 6). B. Use either set. • The left surround speaker connects to the LEFT SURROUND SPEAKER outputs. • The right surround speaker connects to your speaker. Connect the other end of the speaker cord to the red (+) terminal. English
Setting Up
Make the connections
At the...
Owner's guide - Page 10
... shortcircuit and damage the electrical components. Check to -). Left +- to be sure that no loose strands of wire touch across terminals.
Right
+- Left
Left Surround speaker
10 Tighten any loose connections before you plug in the receiver or amplifier and turn it on.
English
Setting Up
Check the connections
Make...
Owner's guide - Page 11
... B to the rear of this guide for screw C at the bottom. Mount bracket part A to the wall and mount bracket part B to bracket part A using screw C.
Figure 8
A
B
Speaker-bracket
installation
C
11
If you are not sturdy enough, or that have hazards concealed behind them, such as electrical wire or plumbing. Secure the...
Owner's guide - Page 12
... ON at the same time.
3. One tone should come from speaker to set to NORMAL surround sound mode
12 13 14 15 16 17 18
11
19
10
20
9
21
8
22
7
23
6
24
5
25
4
26
3
27
2
1 0
28 29 30
Use the test tone on using . Instructions for more details on your receiver to further verify...
Owner's guide - Page 13
... to set the channel output on page 15.
13 If the sound is set at a safe level. You will hear the speaker resume normal play will continue for using the receiver test tone to verify your Dolby Digital receiver
Your VCS-10® or VCS-30® Series II speakers are compatible with the output from Dolby...
Owner's guide - Page 14
... your receiver (see page 10). • Make sure the receiver is not on page 15).
• Make sure your receiver has amplified center and surround
speaker does not
channels. English
...• Make sure headphones are connected to the TV using RCA stereo
cable as well.
• If your authorized Bose® dealer, or contact Bose directly.
14 work
• Be sure your receiver is...
Owner's guide - Page 15
... x 28.0 cm x 16.5 cm; 1.49 kg) VCS-10 speakers, packed in carton: 8 lb (3.6 kg) VCS-30 Series II speaker system, packed in all speakers Automatic electronic protection circuitry in carton: 20 lb (9.1 kg)
15
If necessary, use a mild detergent, like dish soap, being careful not to allow it to Bose. ter channel outputs rated 10-100 watts per channel; rated 4-8 ohms...
Owner's guide - Page 18
©2001 Bose Corporation The Mountain Framingham, MA 01701-9168 USA AM257528 Rev.02
Similar Questions
How To Take Apart Bose Acoustimass 10 Subwoofer
(Posted by dhidt 9 years ago)
Can A Bose 28/35 Center Cube Speaker Be Placed With A Bose Vcs10
I recently got a bose 28/35 and was thinking about purchasing a bose vcs10 to replace the center cub...
I recently got a bose 28/35 and was thinking about purchasing a bose vcs10 to replace the center cub...
(Posted by treyluigs 11 years ago)
