Bissell PowerForce Helix Turbo Bagless Support Question
Bissell PowerForce Helix Turbo Bagless Support Question
Find answers below for this question about Bissell PowerForce Helix Turbo Bagless.Need a Bissell PowerForce Helix Turbo Bagless manual? We have 2 online manuals for this item!
Question posted by Michaelminor16 on March 26th, 2015
Why Is My Vacuum Stop Working
because the motor was rusty
Supporting Images
You can click the images below to enlarge
Current Answers
Answer #1: Posted by BusterDoogen on March 26th, 2015 7:01 AM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,437
Member since:
October 30th, 2011 Points: 28,565,437
The rust may have caused the motor to seize. If it has a hum when you turn it on, pull the plug & lubricate with wd40 around the motor shaft. If it has no hum then the motor has failed. Time for a new one.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Bissell PowerForce Helix Turbo Bagless Manual Pages
User Guide - Page 2
...-day warranty. Today, BISSELL is well made, and we know about floor care went into the design and construction of this powerful, high-tech home vacuuming system. Bissell Chairman & CEO
2 My great-grandfather invented the floor sweeper in the design, manufacture, and service of us at BISSELL. Your BISSELL...
User Guide - Page 3
....
■■ If appliance is not working as it should be observed, including the following:
Read all controls before plugging or unplugging vacuum cleaner.
■■ Use extra care ...pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
■■ Do not use vacuum cleaner in any object into water, have it is running. ■■ Unplug before using an ...
User Guide - Page 4
... Upper Tank
Easy Empty™ Dirt Container
Inner and Outer Circular Filters
Lock 'n Seal™ Lever
Post-Motor Filter (HEPA Media Filter* in select models) Height Adjustment Knob
Powerfoot *The filter media, not the vacuum as a whole, complies with IEST-RP-CC001.5 HEPA standard.
4
Quick Release™ Cord Wrap
Power Cord
Lower...
User Guide - Page 6
... wand and crevice tool together into place.
5. To avoid danger of the brush roll and snap
the TurboBrush® Tool into the front of the vacuum body.
3. Turn the hose to the right to lock into storage clip.
7.
Select models only:
8. Snap the hose into the storage clip. Place the TurboBrush...
User Guide - Page 7
... Cleaning: From normal cleaning position, press handle release pedal once for cleaning under the red power switch on the bottom left of the back of vacuum and clip molded plug to power cord to turn power ON and OFF.
Press the black handle release pedal with foot to upright position and...
User Guide - Page 8
...longer reach.
Press down gently and pull towards you
in tight narrow spaces.
Remove Hose: With vacuum in upright position, grasp the hose wand to dust, blinds,
books, lamps, shelves, and ...foot while turning. If knob is difficult to turn, tilt the cleaner back slightly to stop rotating. Combination dusting brush/
upholstery tool: Rotate for small flat
areas such as stairs,...
User Guide - Page 9
...detergent. Grasp dirt cup portion handle and pull
straight out to "Unlock" position. 3. Unplug vacuum cord from electrical outlet.
2. Grasp the filter located at the bottom of the circular
foam...2
3
electrical outlet
2. Maintenance and Care
To maximize performance and extend life of your vacuum, it is very important to unlock and pull out.
4.
Mild detergent may be wiped...
User Guide - Page 10
... drive belt regularly for wear, cuts, or stressed areas.
7. Clean strings, hair and other debris from electrical outlet.
2. The pre-motor filter is NOT washable.
3.
Unplug vacuum cord from electrical outlet.
2. Unplug vacuum cord from electrical outlet.
2.
Check drive belt for wear or damage.
1. Reposition brush cover and fasten four screws back into...
User Guide - Page 11
... of the vacuum
motor, check for clogs in the vacuum.
Straighten the hose
5
wand base and unclog, with long, narrow
object such as broom stick.
6. Unplug vacuum cord from electrical... into place. Clearing a Clog
Low suction or poor pickup may be due
3
to the vacuum. Maintenance and Care
Replace drive belt
1. Reposition brush cover and fasten four screws back into slots...
User Guide - Page 12
Unplug vacuum cord from belt and clean debris.
5. Twist collar so opening is at the top and lift clear cover to lock into slots on the cover. ... ends into place.
12 Maintenance and Care
TurboBrush® Tool Maintenance (select models only)
1. Turn power OFF. Remove tool from hose or from clip on
vacuum handle.
3.
User Guide - Page 13
... and clean filter
Hose not properly attached
Make sure hose collar is properly installed
Vacuum is not suctioning or blowing
Make sure hose collar is fully connected to need assistance..., BISSELL is full
Empty dirt tank
Clog in home
Check/replace fuse or reset breaker
Vacuum cleaner won 't turn power OFF and
disconnect polarized plug from electrical outlet before performing
maintenance...
User Guide - Page 14
Replacement parts - BISSELL Vacuum
Item 1 2 3 4 5a 5b 6a 6b 7 8 9 10 11 12
Part No. 32074 203-1056 203-1059 203...Hose Assembly (68C7 Series) Brush Roll Assembly (12B1 Series) Brush Roll Assembly (68C7 Series) Pleated Circular Filter Foam Filter Post-Motor HEPA Media Filter* Pre-Motor Filter TurboBrush® Bracket TurboBrush® Tool
1
2
3
4
5a/5b
6a/6b
7
8
11
12
9
10
*The filter ...
User Guide - Page 15
... - 8 pm ET
Or Write: BISSELL Homecare, Inc. Some states do not allow limitations on "If your warranty, contact BISSELL Consumer Care. If you .
15
BISSELL Vacuum
This warranty gives you specific legal rights, and you may vary from the date of charge from state to you have questions about repairs or...
Similar Questions
I Have A Crosswave And Stopped Working When It Sucked Up Part Of A Rug. Is There
reset button
reset button
(Posted by whiteiger123 7 years ago)
How Does Roller Brush Work In A Bissell Powerforce Helix Vacuum
(Posted by armosandm 10 years ago)
Bissell Powerforce Helix Bagless Upright Vacuum Won't Turn On
(Posted by Sankano 10 years ago)
How To Clean Filters In Bissell Powerforce Helix Bagless Upright Vacuum
(Posted by petroot 10 years ago)
Vacuum Stopped Working
I plugged in my bissell pet vacuum and turned it on, it started for a second then shut off now it wo...
I plugged in my bissell pet vacuum and turned it on, it started for a second then shut off now it wo...
(Posted by belizabeth9211 11 years ago)