Bernina Bernette 46 Support Question
Find answers below for this question about Bernina Bernette 46.Need a Bernina Bernette 46 manual? We have 1 online manual for this item!
Question posted by hustonabby on May 3rd, 2014
Bobbin Type?
I am trying to find replacement bobbins for my Bernette 46 and can not find the type to buy anywhere. Please help!
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related Bernina Bernette 46 Manual Pages
Operation Manual - Page 2
Table of Contents
Introduction ...3 Sewing Machine Needles 4 Thread ...6 Presser Feet ...7 Securing Stitches...8 Turning Corners...9 ... Charts 21
8 Series
activa
1008 bernette
aurora 12/13/10
artista
3 Series
The information in this workbook applies to models equipped with the highlighted feature.
2 Note: Some exercises apply only to all current BERNINA and bernette sewing machines.
Operation Manual - Page 3
..., crafters, virtual stitchers, fiber artists and more ideas and information about using your BERNINA or bernette sewing machine.
Introduction
This workbook is reading about it!
3 Each stitch exercise page has a graphic of this workbook have to all types of America blog where you can be used as you don't even have several charts that...
Operation Manual - Page 4
... damage
Needle size - The needle is the most inexpensive part in your sewing machine but it isn't protected by the hook point
Bent - very fine batiste... from hook point and the hook can be traced to a bent, damaged, or incorrect size or type needle. European vs. Sewing Machine Needles
General Information
Along with thread, needles are fully inserted as high as possible, with a larger ...
Operation Manual - Page 5
... on Ultrasuede, vinyl, and plastic. the large groove cradles heavier threads.
Sewing Machine Needles
Type Ballpoint Stretch
Universal Double
Triple Jeans Leather Microtex / Sharp Quilting Topstitch Embroidery
...needle has a more rounded point than a Ballpoint, and a blue anti-cling coating which helps to a single shank.
For pintucks, hems, and decorative work , such as polyester, acrylic...
Operation Manual - Page 6
..., bobbinwork 40 wt.-
Cotton thread stretches less than cotton, it blends into your sewing machine, potentially causing tension inconsistencies and possibly even damage to make a single thread. Silk... heirloom, appliqué, bobbin thread 80 wt.-
excellent for Thread Weights
12 wt.- Rayon A lustrous embroidery thread; Mettler 50/2; Poor quality or the wrong type of thread can cause ...
Operation Manual - Page 7
... and a maximum stitch width of 9mm.
The "C" stands for all BERNINA machines. These machines are also compatible with the one or two additional versions with professional results
▪...Feature is followed by the best and most complete educational materials in the cutout on all types of sewing (example, quilting, garment-making them sturdy and durable
▪ are easy to see Feet...
Operation Manual - Page 8
... the end in half lengthwise to be 2" x 6". Select the Securing Stitch. The machine will sew in reverse until the Quick Reverse Button/Lever is released.
Continue stitching the seam; Securing...bernette Presser Foot: Zigzag/Universal Foot
Fold each piece of fabric in the same way. Fold one 6" edge with the ⅝" guide line.
Select the straight stitch. Do you know how to sew; machine...
Operation Manual - Page 9
...to form at least 2 right angle corners and 2 additional corners. Sew several lines of stitching, pivoting to set to raise the presser foot.... needle down . To change needle setting, touch the Needle Down icon. Machine will go up or down and the presser foot up position (default). ... Foot #1/1C/1D bernette Presser Foot: Zigzag/Universal Foot
Select the straight stitch. Place the fabric ...
Operation Manual - Page 10
...as a guide. Guide the edge of the fabric under the middle of the fabric. sew using the following steps. Match the weight of the thread to the weight of the ...: 80/12 Universal Needle Position: As directed in instructions BERNINA Presser Foot: Reverse Pattern Foot #1/1C/1D bernette Presser Foot: Zigzag/Universal Foot
Select the Zigzag Stitch (width = 4, length = 2).
Tips Do not ...
Operation Manual - Page 11
.../13/10
Do you know how to the machine. Adjust the stitch width if needed so that the stitches barely show on the outside of the fabric. Sew on the extended hem allowance, keeping the folded...As programmed BERNINA Presser Foot: Reverse Pattern Foot #1/1C/1D and
Blind Hem Foot #5 bernette Presser Foot: Zigzag/Universal Foot and
Blind Hem Foot (optional accessory)
Attach Reverse Pattern Foot #1 or...
Operation Manual - Page 12
... #1/1C/1D or bernette Zigzag/ Universal Foot to : ▪ Adjust the needle position? ▪ Use the stitch plate markings? ▪ Use Edgestitch Foot #10/10C/10D?
12 Position the edge of the seam, sewing in the same direction as before.
12/13/10
Do you know how to the machine. Change to Edgestitch...
Operation Manual - Page 14
...Ballpoint may also be used) Needle Position: As programmed BERNINA Presser Foot: Reverse pattern Foot #1/1C/1D bernette Presser Foot: Zigzag/Universal Foot
Select the Super Stretch stitch.
Note: If the fabric is pulling and ... the fabric on the ⅝" marking on the fabric and eliminate the stretching. sew the seam and press it is sewn, adjust the presser foot pressure to a lower number ...
Operation Manual - Page 15
...drop the feed dog and sew a bartack
(see page 19) at the beginning of the stitching and then pull it to gather the sample to the machine.
Tie a knot in ... stitch width and length? ▪ Drop the feed dog?
15 sewing over cord adds additional strength, eliminates thread
breakage, and allows better control of the bernette Cording Foot, leaving a 2"-3" tail behind the foot. Gathering Over ...
Operation Manual - Page 17
...bernette - Tension Tips A slightly tighter bobbin tension gives a beautiful full look to achieve this:
• CB Hook Machines: Thread the bobbin thread through the hole in order and sew...12 Universal Needle Position: As programmed BERNINA Presser Foot: Standard Buttonhole Foot #3/3C bernette Presser Foot: Models 46 & 56 only: 4-step Buttonhole Foot
Note: For making buttonholes with remaining ...
Operation Manual - Page 18
... Bring the thread tails to another place on the drawn line and sew the programmed buttonhole on the second line. the machine will simply repeat the previous buttonhole and stop when the red mark on...the length of the foot.
12/13/10
Do you know how to 3" x 6"; Continue sewing - Automatic Buttonhole-bernette 66 and 92c ▪ Position the foot over the drawn line, setting it toward the ...
Operation Manual - Page 19
... thread tails as part of the button by setting the stitch length at 0.0mm. BERNINA or bernette: Use the Universal or Zigzag stitch, sew 6-8 stitches, and stop.
press. BERNINA only: For a long shank, adjust the pin on stitch, the machine stops automatically when the program is appropriate for coat- If using the Button...
Operation Manual - Page 20
... zipper, stitching through all layers. adjust the needle position (bernette users slide the zipper foot) to the right or left side of 2.5mm. Right Side: Adjust the guide one notch to the project. Sew up the left as needed to stitch close to : ▪ Machine baste a seam? ▪ Adjust the needle positions? ▪...
Operation Manual - Page 21
...630
21
21 21 21 30
30
Blindstitch
9
9
9
9
9
9
Button Sew-On
60
60 60 60 60
60
Quilter's Securing
1324 1324 324 324 324...4
6
6
8 --
3
3
3
--
3
6
5 76
2
2
2
2
2
3
3 33
* The stitches on bernette model 46 are not numbered on the machine but are used in the order they appear on the chart in Workbook 1: Basic Operation. indicates that the stitch is not available).
...
Operation Manual - Page 22
Machine Features & Functions
The following features and functions are used in Workbook 1: Basic Operation.
8 Series
artista
Feature/ Function 830 820 730 640 635LE 630...yes yes
11
11
11
yes yes yes
no
no
no
yes yes yes yes yes yes
3 Series
activa mechanical
bernette
380 350PE 330 210
1008 92c 66 56 46
yes yes yes no
no
yes yes yes no
yes yes yes yes yes opt opt no
yes yes yes ...
Operation Manual - Page 23
...bernette foot does not have snap-on soles.
Sideways Motion Foot #40C
40C
-- 40C --
--
--
X
20
--
20
--
-- B
D
--
X
X
--
--
--
--
--
--
--
--
--
--
--
--
--
--
46...
8
--
8
--
--
--
--
--
--
--
-- Darning Foot #9
--
--
--
9
--
9
Button Sew-On Foot #18
18
-- 18 --
--
--
Freemotion Couching Foot #43
--
--
-- --
43
--
indicates that...
Similar Questions
My Bernette 46 Will Not Descend Into The Bobbing. It Jams About Half Way In.
(Posted by kabaz 8 years ago)
New Bulb Not Working In Sewing Machine Bernette 12 What Can It Be
(Posted by Anonymous-152221 8 years ago)
My Sewing Machine Bernette 15 Stops Working
After 1 day using my Bernette 15 stops working - engine hoots but doesn't rotate spindle and hand wh...
After 1 day using my Bernette 15 stops working - engine hoots but doesn't rotate spindle and hand wh...
(Posted by sgrayxx 12 years ago)