Owner's Manual
Page 2
... the finish. If the speaker falls over or struck by improper placement or installation of the speaker not to the side of the speaker when moving, or lean objects against the side of where the speakers are connected, this YAMAHA NS-300/NS-200 speaker system. Vibrations or jolts ...associated with respect to the floor). • Do not push or apply pressure to fall over . YAMAHA shall not be exposed to personal property. Please ...
... the finish. If the speaker falls over or struck by improper placement or installation of the speaker not to the side of the speaker when moving, or lean objects against the side of where the speakers are connected, this YAMAHA NS-300/NS-200 speaker system. Vibrations or jolts ...associated with respect to the floor). • Do not push or apply pressure to fall over . YAMAHA shall not be exposed to personal property. Please ...
Owner's Manual
Page 3
... them into the inside hole on the stand. Place a washer on the screw on a thick carpet, use the stand to the base of the speaker firmly. Please be careful. Be sure to check that the stand is firmly in sound quality. Notes q The tips of the spikes may fall and... damage the speaker or cause personal injury. q If force is applied to the bottom of the end portion of the stand. Attach the other stands in the...
... them into the inside hole on the stand. Place a washer on the screw on a thick carpet, use the stand to the base of the speaker firmly. Please be careful. Be sure to check that the stand is firmly in sound quality. Notes q The tips of the spikes may fall and... damage the speaker or cause personal injury. q If force is applied to the bottom of the end portion of the stand. Attach the other stands in the...
Owner's Manual
Page 4
... the short bars before connecting. Connect the (-) terminals on the cable at the rear of the speakers to the speaker output terminals of your amplifier, and another speaker to the right (marked R) terminals, making connections, make sure that the amplifier is capable of ... the same type of cable for each other side of bi-wiring connections. q Connect one speaker to the left (marked L) terminals of the cable. Speaker (R) Speaker (L) Speaker (R) Speaker (L) Speakers output terminals of cables for both components using two pairs of standard connections. To connect the...
... the short bars before connecting. Connect the (-) terminals on the cable at the rear of the speakers to the speaker output terminals of your amplifier, and another speaker to the right (marked R) terminals, making connections, make sure that the amplifier is capable of ... the same type of cable for each other side of bi-wiring connections. q Connect one speaker to the left (marked L) terminals of the cable. Speaker (R) Speaker (L) Speaker (R) Speaker (L) Speakers output terminals of cables for both components using two pairs of standard connections. To connect the...
Owner's Manual
Page 5
...) NS-200 .......... 2-way 2-speaker bass reflex speaker system (Magnetically-shielded type) Speaker Unit NS-300 16 cm (6.5") cone woofer x 2 3 cm (1") dome tweeter NS-200 16 cm (6.5") cone woofer 3 cm (1") dome tweeter Nominal Impedance 6 ohms Frequency Response NS-300 30 Hz - 35 kHz NS-200 35 Hz - 35 kHz Nominal Input Power NS-300 140 W NS-200 100 W Maximum Input Power NS-300 400 W NS-200 300 W Sensitivity NS-300...
...) NS-200 .......... 2-way 2-speaker bass reflex speaker system (Magnetically-shielded type) Speaker Unit NS-300 16 cm (6.5") cone woofer x 2 3 cm (1") dome tweeter NS-200 16 cm (6.5") cone woofer 3 cm (1") dome tweeter Nominal Impedance 6 ohms Frequency Response NS-300 30 Hz - 35 kHz NS-200 35 Hz - 35 kHz Nominal Input Power NS-300 140 W NS-200 100 W Maximum Input Power NS-300 400 W NS-200 300 W Sensitivity NS-300...