Owner's Manual
Page 2
... be liable for selecting this YAMAHA NS-300/NS-200 speaker system. For safe and proper use the stands regardless of injury (or even death) to persons and/or damage to falling over . Vibrations or jolts ...associated with chemical solvents as this does not guarantee that even though the stands are positioned. Never allow your amplifier to a lower setting. Otherwise the speaker...
... be liable for selecting this YAMAHA NS-300/NS-200 speaker system. For safe and proper use the stands regardless of injury (or even death) to persons and/or damage to falling over . Vibrations or jolts ...associated with chemical solvents as this does not guarantee that even though the stands are positioned. Never allow your amplifier to a lower setting. Otherwise the speaker...
Owner's Manual
Page 3
... the other stands in the same manner and confirm that all 4 stands have been attached, tighten both screws have been firmly attached. Place the speaker in an upright position and adjust the length of the spike to match the depth of the carpet. When adjustment is applied to the... be careful. Procedure: Put the 6 mm screw through the outside holes on a thick carpet, use the stand to the speaker at each of the speaker, it may fall and damage the speaker or cause personal injury. Procedure: Set the nut close to the tip of the spike and screw them into...
... the other stands in the same manner and confirm that all 4 stands have been attached, tighten both screws have been firmly attached. Place the speaker in an upright position and adjust the length of the spike to match the depth of the carpet. When adjustment is applied to the... be careful. Procedure: Put the 6 mm screw through the outside holes on a thick carpet, use the stand to the speaker at each of the speaker, it may fall and damage the speaker or cause personal injury. Procedure: Set the nut close to the tip of the spike and screw them into...
Owner's Manual
Page 4
... insulation from the terminals first, and then connect the woofer and tweeter to the amplifier separately using one speaker to the left (marked L) terminals of cables. Note For bi-wiring connections, use the same type of... by tugging lightly on the cable at the rear of the cable. Speaker (R) + Speaker (L) Woofer terminals - q Connect one side of the speakers to match the polarity. L A -+ B SPEAKERS R L +- -+ SPEAKERS R +- Speaker (R) Speaker (L) Speaker (R) Speaker (L) Speakers output terminals of standard connections and bi-wiring connections. q Connect the ...
... insulation from the terminals first, and then connect the woofer and tweeter to the amplifier separately using one speaker to the left (marked L) terminals of cables. Note For bi-wiring connections, use the same type of... by tugging lightly on the cable at the rear of the cable. Speaker (R) + Speaker (L) Woofer terminals - q Connect one side of the speakers to match the polarity. L A -+ B SPEAKERS R L +- -+ SPEAKERS R +- Speaker (R) Speaker (L) Speaker (R) Speaker (L) Speakers output terminals of standard connections and bi-wiring connections. q Connect the ...
Owner's Manual
Page 5
...) NS-200 .......... 2-way 2-speaker bass reflex speaker system (Magnetically-shielded type) Speaker Unit NS-300 16 cm (6.5") cone woofer x 2 3 cm (1") dome tweeter NS-200 16 cm (6.5") cone woofer 3 cm (1") dome tweeter Nominal Impedance 6 ohms Frequency Response NS-300 30 Hz - 35 kHz NS-200 35 Hz - 35 kHz Nominal Input Power NS-300 140 W NS-200 100 W Maximum Input Power NS-300 400 W NS-200 300 W Sensitivity NS...
...) NS-200 .......... 2-way 2-speaker bass reflex speaker system (Magnetically-shielded type) Speaker Unit NS-300 16 cm (6.5") cone woofer x 2 3 cm (1") dome tweeter NS-200 16 cm (6.5") cone woofer 3 cm (1") dome tweeter Nominal Impedance 6 ohms Frequency Response NS-300 30 Hz - 35 kHz NS-200 35 Hz - 35 kHz Nominal Input Power NS-300 140 W NS-200 100 W Maximum Input Power NS-300 400 W NS-200 300 W Sensitivity NS...