Owner's Manual
Page 3
... from speaker output jacks L and R of the EMX2000 and enjoy long, trouble-free performance, please read this owner's manual carefully, and keep it in . You can connect one or two speakers to the speaker output jacks, two stereo output channels for purchasing the Yamaha EMX2000 Powered Mixer. You can be applied to add reverberation or...
... from speaker output jacks L and R of the EMX2000 and enjoy long, trouble-free performance, please read this owner's manual carefully, and keep it in . You can connect one or two speakers to the speaker output jacks, two stereo output channels for purchasing the Yamaha EMX2000 Powered Mixer. You can be applied to add reverberation or...
Owner's Manual
Page 9
... L-ST R The STEREO bus signals are sent from the mixer section to the power amp section. X POWER indicator This indicator will light up when the power of 3mm or less to play a loud sound. EMX2000-Owner's Manual Use a screwdriver of a width of the EMX2000 is adjusted by the master MONO fader. If an external...
... L-ST R The STEREO bus signals are sent from the mixer section to the power amp section. X POWER indicator This indicator will light up when the power of 3mm or less to play a loud sound. EMX2000-Owner's Manual Use a screwdriver of a width of the EMX2000 is adjusted by the master MONO fader. If an external...
Owner's Manual
Page 11
...an external device, such as a tape deck and CD player, to be set to ON in order to this jack, the corresponding channel of a sub mixer. EMX2000-Owner's Manual Note: Use only the L phone (A) jacks to connect a monaural device that has phone jacks. 4 ST SUB 1 (stereo sub 1) jacks ST SUB... the signal from this jack. A EFFECT jack The input of a monitor system is connected. C FOOT SW (foot switch) jack A separately sold Yamaha FC5 foot switch can be connected to use a "Y" cable to connect to select phone jacks (A) or phono jacks (B). Adjust the recording level on the...
...an external device, such as a tape deck and CD player, to be set to ON in order to this jack, the corresponding channel of a sub mixer. EMX2000-Owner's Manual Note: Use only the L phone (A) jacks to connect a monaural device that has phone jacks. 4 ST SUB 1 (stereo sub 1) jacks ST SUB... the signal from this jack. A EFFECT jack The input of a monitor system is connected. C FOOT SW (foot switch) jack A separately sold Yamaha FC5 foot switch can be connected to use a "Y" cable to connect to select phone jacks (A) or phono jacks (B). Adjust the recording level on the...
Owner's Manual
Page 19
...• In these specifications when dB represents a specific voltage, 0 dB is referenced to change without prior notice. before cliping Connectors on mixer MIC INPUT (1-8) MAX MIN LINE INPUT (1-8) MAX MIN ST INPUT (9-12) MAX MIN ST SUB IN (1, 2) TAPE IN (L, R) CH INSERT IN ...XLR type connectors and PHONE JACKS (TRS) (T=HOT, R=COLD, S=GND) are subject to 0.775 Vrms, 0 dBV is set at maximum gain. 2. EMX2000-Owner's Manual PHONE JACKS are unbalanced. • In these specifications when dB represents a specific voltage, 0 dB is referenced to 1 Vrms. s ...
...• In these specifications when dB represents a specific voltage, 0 dB is referenced to change without prior notice. before cliping Connectors on mixer MIC INPUT (1-8) MAX MIN LINE INPUT (1-8) MAX MIN ST INPUT (9-12) MAX MIN ST SUB IN (1, 2) TAPE IN (L, R) CH INSERT IN ...XLR type connectors and PHONE JACKS (TRS) (T=HOT, R=COLD, S=GND) are subject to 0.775 Vrms, 0 dBV is set at maximum gain. 2. EMX2000-Owner's Manual PHONE JACKS are unbalanced. • In these specifications when dB represents a specific voltage, 0 dB is referenced to 1 Vrms. s ...