Use & Care Guide
Page 12
... the power supply cord. 2. Shut off water faucet. 4. Flush water pipes. Steam models only: Shut off water faucet. 3. Non-Use or Storage Care Operate your dryer only when you are secure in dryer base. 8. Moving Care For power supply cord-connected dryers: 1. Gas models only: Close shutoff valve in the "Installation Instructions". Periodically inspect and replace...
... the power supply cord. 2. Shut off water faucet. 4. Flush water pipes. Steam models only: Shut off water faucet. 3. Non-Use or Storage Care Operate your dryer only when you are secure in dryer base. 8. Moving Care For power supply cord-connected dryers: 1. Gas models only: Close shutoff valve in the "Installation Instructions". Periodically inspect and replace...
Installation Guide
Page 4
Read and follow the instructions provided with dryer) Check local codes. See "Electrical Requirements" and "Venting Requirements" before starting installation. For further information, please refer to LP gas Parts supplied (all parts are included. INSTALLATION REQUIREMENTS TOOLS AND PARTS ...mm) or 10" (254 mm) adjustable wrench (for gas connections) Flat-blade screwdriver Adjustable wrench that all models): Utility knife Tin snips (new vent installations) Tape measure Leveling legs (4) Parts supplied (steam models): Caulking gun and compound (for installing new exhaust vent...
Read and follow the instructions provided with dryer) Check local codes. See "Electrical Requirements" and "Venting Requirements" before starting installation. For further information, please refer to LP gas Parts supplied (all parts are included. INSTALLATION REQUIREMENTS TOOLS AND PARTS ...mm) or 10" (254 mm) adjustable wrench (for gas connections) Flat-blade screwdriver Adjustable wrench that all models): Utility knife Tin snips (new vent installations) Tape measure Leveling legs (4) Parts supplied (steam models): Caulking gun and compound (for installing new exhaust vent...
Installation Guide
Page 5
... Requirements". ■■ A separate 15 or 20-amp circuit needed for gas dryers and 30-amp circuit needed for electric dryers. ■■ If using the "Y" connector provided. LOCATION REQUIREMENTS INSTALLATION CLEARANCES The location must support dryer weight of 20-100 psi (137.9-689.6 kPa). If slope is greater ...than 1", clothes may not tumble properly and automatic sensor cycles may use the water supply for your dryer at least 18" (460 mm) above floor. ■■ Steam models only: Cold water faucets located within 2 ft. (610 mm) of either side of 1" (25 mm)...
... Requirements". ■■ A separate 15 or 20-amp circuit needed for gas dryers and 30-amp circuit needed for electric dryers. ■■ If using the "Y" connector provided. LOCATION REQUIREMENTS INSTALLATION CLEARANCES The location must support dryer weight of 20-100 psi (137.9-689.6 kPa). If slope is greater ...than 1", clothes may not tumble properly and automatic sensor cycles may use the water supply for your dryer at least 18" (460 mm) above floor. ■■ Steam models only: Cold water faucets located within 2 ft. (610 mm) of either side of 1" (25 mm)...
Installation Guide
Page 8
... and Company. 8 B A 4 1/2" (115 mm) 1" (25 mm) A. 1/2" NPT gas supply line B. 3/8" NPT dryer pipe NOTE: If the dryer is mounted on the pedestal model. For a garage installation, the gas pipe height must be an additional 18" (460 mm) from the gas specified on the model/serial number plate is required for gas appliances, ANSI Z21.24 or CSA 6.10...
... and Company. 8 B A 4 1/2" (115 mm) 1" (25 mm) A. 1/2" NPT gas supply line B. 3/8" NPT dryer pipe NOTE: If the dryer is mounted on the pedestal model. For a garage installation, the gas pipe height must be an additional 18" (460 mm) from the gas specified on the model/serial number plate is required for gas appliances, ANSI Z21.24 or CSA 6.10...
Installation Guide
Page 12
...-joint compound resistant to dryer location using the new inlet hoses. Check and see if rubber washer is a registered trademark of LP gas. Install exhaust hood 12" min. (305 mm) 12" min. (305 mm) Install exhaust hood and use old hoses. 1. Connect Inlet Hoses For non-steam models, skip to gas pipe. Dupont De...
...-joint compound resistant to dryer location using the new inlet hoses. Check and see if rubber washer is a registered trademark of LP gas. Install exhaust hood 12" min. (305 mm) 12" min. (305 mm) Install exhaust hood and use old hoses. 1. Connect Inlet Hoses For non-steam models, skip to gas pipe. Dupont De...
Installation Guide
Page 15
... different parts of the two hinges in your "Use and Care Guide". Gas Models: q Check that dryer is level. Do not select Air Only Temperature setting. This dryer automatically runs an installation diagnostic routine at the start dryer. q Check dryer's final location. q Check that gas supply is recommended to control the buildup of scale through steps to...
... different parts of the two hinges in your "Use and Care Guide". Gas Models: q Check that dryer is level. Do not select Air Only Temperature setting. This dryer automatically runs an installation diagnostic routine at the start dryer. q Check dryer's final location. q Check that gas supply is recommended to control the buildup of scale through steps to...