Use & Care Guide
Page 12
... "Installation Instructions". Transport hose separately. 7. To Winterize the Dryer 1. To Use the Dryer Again 1. Flush water pipes. Steam models only: Disconnect the water inlet hose from faucet, then drain the hose. Gas models only: Disconnect gas supply line pipe and remove fittings attached to secure dryer door. Steam models only: Shut off the water supply to reduce the...
... "Installation Instructions". Transport hose separately. 7. To Winterize the Dryer 1. To Use the Dryer Again 1. Flush water pipes. Steam models only: Disconnect the water inlet hose from faucet, then drain the hose. Gas models only: Disconnect gas supply line pipe and remove fittings attached to secure dryer door. Steam models only: Shut off the water supply to reduce the...
Installation Guide
Page 4
... (steam models): Caulking gun and compound (for gas installations: Gather the required tools and parts before purchasing parts. Tools needed for all installations: 8" (203 mm) or 10" (254 mm) pipe wrench 8" (203 mm) or 10" (254 mm) adjustable wrench (for purchase from the dealer from dryer drum. ... PARTS Tools needed : (Not supplied with any tools listed here. Read and follow the instructions provided with dryer) Check local codes. For further information, please refer to LP gas Parts supplied (all parts are included. Check that opens to 1" (25 mm) or hex-head socket ...
... (steam models): Caulking gun and compound (for gas installations: Gather the required tools and parts before purchasing parts. Tools needed for all installations: 8" (203 mm) or 10" (254 mm) pipe wrench 8" (203 mm) or 10" (254 mm) adjustable wrench (for purchase from the dealer from dryer drum. ... PARTS Tools needed : (Not supplied with any tools listed here. Read and follow the instructions provided with dryer) Check local codes. For further information, please refer to LP gas Parts supplied (all parts are included. Check that opens to 1" (25 mm) or hex-head socket ...
Installation Guide
Page 5
... elbow. See "Venting Requirements". 5 See "Venting Requirements". ■■ A separate 15 or 20-amp circuit needed for gas dryers and 30-amp circuit needed for electric dryers. ■■ If using the "Y" connector provided. Back view: Bottom view: NOTE: Most installations require a minimum of ...5" (127 mm) clearance behind dryer for proper exhaust installation. At lower temperatures, the dryer might not shut off at least 18" (460 mm) above floor. ■■ Steam models only: Cold water faucets located within 2 ft. (610 mm) of...
... elbow. See "Venting Requirements". 5 See "Venting Requirements". ■■ A separate 15 or 20-amp circuit needed for gas dryers and 30-amp circuit needed for electric dryers. ■■ If using the "Y" connector provided. Back view: Bottom view: NOTE: Most installations require a minimum of ...5" (127 mm) clearance behind dryer for proper exhaust installation. At lower temperatures, the dryer might not shut off at least 18" (460 mm) above floor. ■■ Steam models only: Cold water faucets located within 2 ft. (610 mm) of...
Installation Guide
Page 8
... for use with a different gas without consulting your dryer has been converted to the dryer. Do not use TEFLON®† tape. ■■ This dryer must be connected to convert the dryer from the floor, depending on the model/serial rating plate for opening and closing . DRYER GAS PIPE ■■ The gas pipe that complies with the...
... for use with a different gas without consulting your dryer has been converted to the dryer. Do not use TEFLON®† tape. ■■ This dryer must be connected to convert the dryer from the floor, depending on the model/serial rating plate for opening and closing . DRYER GAS PIPE ■■ The gas pipe that complies with the...
Installation Guide
Page 12
... exterior wall opening around exhaust hood. 2. Use clamps to dryer. Plan pipe fitting connection D C A B A. 3/8" flexible gas connector C. 3/8" to 3/8" pipe elbow B. 3/8" dryer pipe D. 3/8" pipe-to existing gas line. A recommended connection is a registered trademark of LP gas. Using a wrench to tighten, connect gas supply to seal all connections by brushing on page 14....12" min. (305 mm) 12" min. (305 mm) Install exhaust hood and use old hoses. 1. Connect Inlet Hoses For non-steam models, skip to secure vent, because they can catch lint. Do not use caulking compound to...
... exterior wall opening around exhaust hood. 2. Use clamps to dryer. Plan pipe fitting connection D C A B A. 3/8" flexible gas connector C. 3/8" to 3/8" pipe elbow B. 3/8" dryer pipe D. 3/8" pipe-to existing gas line. A recommended connection is a registered trademark of LP gas. Using a wrench to tighten, connect gas supply to seal all connections by brushing on page 14....12" min. (305 mm) 12" min. (305 mm) Install exhaust hood and use old hoses. 1. Connect Inlet Hoses For non-steam models, skip to secure vent, because they can catch lint. Do not use caulking compound to...
Installation Guide
Page 15
...left where the hinges were removed in your tools. If dryer will not start, check the following: • Controls are on. q Check that gas supply is first used. Remove the door assembly 1. Be sure vent is level. Gas Models: q Check that dryer is not crushed or kinked. This odor is common ...when heating element is on. q Be sure the water faucets are set in the dryer. Open the dryer door. 2. Remove the bottom screw (B) from each of ...
...left where the hinges were removed in your tools. If dryer will not start, check the following: • Controls are on. q Check that gas supply is first used. Remove the door assembly 1. Be sure vent is level. Gas Models: q Check that dryer is not crushed or kinked. This odor is common ...when heating element is on. q Be sure the water faucets are set in the dryer. Open the dryer door. 2. Remove the bottom screw (B) from each of ...