Installation Guide
Page 2
...Standpipe Adapter Part Number 3363920 Connector Kit Part Number 285835 Extension Drain Hose Part Number 285863 Connector Kit Part Number 285835 Drain Protector Part Number 367031 Connector Kit Part Number 285835 Siphon Break Kit Part Number 285834 Connector Kit (x2) Part Number 285835 Extension Drain Hose Part Number ... to 19⁄16" (39.5 mm) Optional tools: Flashlight Bucket Parts needed: (Not supplied with washer) Water inlet hoses (2) Flat inlet hose washers (4) Parts supplied: NOTE: All parts supplied for some installations, not supplied with washer) Your installation may be...
...Standpipe Adapter Part Number 3363920 Connector Kit Part Number 285835 Extension Drain Hose Part Number 285863 Connector Kit Part Number 285835 Drain Protector Part Number 367031 Connector Kit Part Number 285835 Siphon Break Kit Part Number 285834 Connector Kit (x2) Part Number 285835 Extension Drain Hose Part Number ... to 19⁄16" (39.5 mm) Optional tools: Flashlight Bucket Parts needed: (Not supplied with washer) Water inlet hoses (2) Flat inlet hose washers (4) Parts supplied: NOTE: All parts supplied for some installations, not supplied with washer) Your installation may be...
Installation Guide
Page 4
...tie. install no higher than 96" (2.44 m) from bottom of washer. See "Alternate Parts". See "Alternate Parts". If you need to 1" (25 mm) diameter Standpipe Adapter Kit is available (Part Number 3363920). Minimum carry-away capacity: 17 gal. (64 L) per minute. IMPORTANT: ... mm) Minimum diameter for floor standpipe drain system. 4 Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be purchased separately. Floor drain system 4.5" (114 mm) See requirements for a...
...tie. install no higher than 96" (2.44 m) from bottom of washer. See "Alternate Parts". See "Alternate Parts". If you need to 1" (25 mm) diameter Standpipe Adapter Kit is available (Part Number 3363920). Minimum carry-away capacity: 17 gal. (64 L) per minute. IMPORTANT: ... mm) Minimum diameter for floor standpipe drain system. 4 Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be purchased separately. Floor drain system 4.5" (114 mm) See requirements for a...
Installation Guide
Page 6
...to avoid suspension and structural damage, a certified technician must properly set up washer for relocation. 6 Squeeze clamp with clamp. See "Alternate Parts". NOTE: If washer is not already in Step 8. Pull power cord through opening in until installation has been completed. Discard bolts and ...spacers. 4. IMPORTANT: Do not plug washer in rear panel and close hole with washer parts. 5. For a floor drain, remove the preinstalled drain hose form as shown. CONNECT DRAIN HOSE 7. Gently place power cord over top...
...to avoid suspension and structural damage, a certified technician must properly set up washer for relocation. 6 Squeeze clamp with clamp. See "Alternate Parts". NOTE: If washer is not already in Step 8. Pull power cord through opening in until installation has been completed. Discard bolts and ...spacers. 4. IMPORTANT: Do not plug washer in rear panel and close hole with washer parts. 5. For a floor drain, remove the preinstalled drain hose form as shown. CONNECT DRAIN HOSE 7. Gently place power cord over top...
Installation Guide
Page 7
...with new inlet hoses with flat washers (not provided). Both hoses must be connected to washer correctly. 8. You may need to avoid clogs. See "Alternate Parts". 9. do not force excess hose into standpipe (shown in picture) or over each other when attached correctly. 12. Drain hose form must be connected ... water to faucets or washer. Do not use old hoses. Repeat this step with separate directions. In most standard configurations, hoses will need additional parts with the hose labeled cold for the cold water faucet. Washer must be inside standpipe;
...with new inlet hoses with flat washers (not provided). Both hoses must be connected to washer correctly. 8. You may need to avoid clogs. See "Alternate Parts". 9. do not force excess hose into standpipe (shown in picture) or over each other when attached correctly. 12. Drain hose form must be connected ... water to faucets or washer. Do not use old hoses. Repeat this step with separate directions. In most standard configurations, hoses will need additional parts with the hose labeled cold for the cold water faucet. Washer must be inside standpipe;
Installation Guide
Page 9
... foot clockwise to lower the washer or counterclockwise to see what was skipped. Do not use an extension cord. q Check that washer is an extra part, go back through steps to raise the washer. q Check for a medium-size load. 9 q Dispose of washer and that all four feet are... firmly in death, fire, or electrical shock. 20. Plug into a grounded 3 prong outlet. q Check that all parts are about 1/2" (13 mm) from back of washer about 4" (102 mm) with the floor. Adjust leveling feet WARNING Jam nut If washer is level and...
... foot clockwise to lower the washer or counterclockwise to see what was skipped. Do not use an extension cord. q Check that washer is an extra part, go back through steps to raise the washer. q Check for a medium-size load. 9 q Dispose of washer and that all four feet are... firmly in death, fire, or electrical shock. 20. Plug into a grounded 3 prong outlet. q Check that all parts are about 1/2" (13 mm) from back of washer about 4" (102 mm) with the floor. Adjust leveling feet WARNING Jam nut If washer is level and...