Installation Guide
Page 2
...hole plugs (4) If you have: Overhead sewer 1" (25 mm) standpipe Drain hose too short Lint clogged drain Floor drain system You will need: Standard 20 gal. (76 L) 39" (990 mm) tall drain tub or utility sink, sump pump and connectors (available from local plumbing suppliers) 2" (51 mm) diameter ...AND PARTS Gather required tools and parts before starting installation. Alternate parts: (Not supplied with clamp and form (may require additional parts. Drain hose with washer) Your installation may be required for installation are in the washer basket. To order, please refer to 1" (25 ...
...hole plugs (4) If you have: Overhead sewer 1" (25 mm) standpipe Drain hose too short Lint clogged drain Floor drain system You will need: Standard 20 gal. (76 L) 39" (990 mm) tall drain tub or utility sink, sump pump and connectors (available from local plumbing suppliers) 2" (51 mm) diameter ...AND PARTS Gather required tools and parts before starting installation. Alternate parts: (Not supplied with clamp and form (may require additional parts. Drain hose with washer) Your installation may be required for installation are in the washer basket. To order, please refer to 1" (25 ...
Installation Guide
Page 4
... Extension Drain Hose (Part Number 285863) that may be at least 30" (762 mm) high; If you need to 1" (25 mm) diameter Standpipe Adapter Kit is available (Part Number 3363920). See "Alternate Parts". A 1/4" (6 mm) diameter to pump higher than 96" (2.44 m), a sump pump and associated... mm) on all sides of washer. ** Recommended 4" (102 mm), minimum 1.5" (38 mm) DRAIN SYSTEM Drain system can be inside standpipe. IMPORTANT: To avoid siphoning, only 4.5" (114 mm) of washer. Always secure drain hose with cable tie. Minimum carry-away capacity: 17 gal. (64 L) per minute. See "...
... Extension Drain Hose (Part Number 285863) that may be at least 30" (762 mm) high; If you need to 1" (25 mm) diameter Standpipe Adapter Kit is available (Part Number 3363920). See "Alternate Parts". A 1/4" (6 mm) diameter to pump higher than 96" (2.44 m), a sump pump and associated... mm) on all sides of washer. ** Recommended 4" (102 mm), minimum 1.5" (38 mm) DRAIN SYSTEM Drain system can be inside standpipe. IMPORTANT: To avoid siphoning, only 4.5" (114 mm) of washer. Always secure drain hose with cable tie. Minimum carry-away capacity: 17 gal. (64 L) per minute. See "...
Dimension Guide
Page 2
...sewer and need . Floor drain system 4.5" (114 mm) See requirements for a standpipe drain: 2" (51 mm). Specifications subject to change without notice. If a closet door or louvered door is installed, top and bottom air openings in door are needed .) Because Whirlpool Corporation policy includes a ...avoid siphoning, only 4.5" (114 mm) of washer. (Additional hoses may be large enough to allow door to pump higher than 96" (2.44 m), a sump pump and associated hardware are required. For each arrangement, consider allowing more space for ease of laundry tub must be ...
...sewer and need . Floor drain system 4.5" (114 mm) See requirements for a standpipe drain: 2" (51 mm). Specifications subject to change without notice. If a closet door or louvered door is installed, top and bottom air openings in door are needed .) Because Whirlpool Corporation policy includes a ...avoid siphoning, only 4.5" (114 mm) of washer. (Additional hoses may be large enough to allow door to pump higher than 96" (2.44 m), a sump pump and associated hardware are required. For each arrangement, consider allowing more space for ease of laundry tub must be ...
Use & Care Guide
Page 16
...and soil level. Then touch POWER again to clear the code. Touch POWER once to clear the display. F5 followed by E1 (drain pump system error) appears in display Not using HE detergent or using too much HE detergent. Close the door completely. Check for assistance and... appears in display F9 followed by E2 (door will display this error code during Clean Washer with affresh® cycle. In Canada www.whirlpool.ca for items in display Door not closed completely and latching. Troubleshooting First try the solutions suggested here or visit our website at least...
...and soil level. Then touch POWER again to clear the code. Touch POWER once to clear the display. F5 followed by E1 (drain pump system error) appears in display Not using HE detergent or using too much HE detergent. Close the door completely. Check for assistance and... appears in display F9 followed by E2 (door will display this error code during Clean Washer with affresh® cycle. In Canada www.whirlpool.ca for items in display Door not closed completely and latching. Troubleshooting First try the solutions suggested here or visit our website at least...
Use & Care Guide
Page 17
... suggested here or visit our website at certain stages of the cycle. Check floor for leaks or clogged sink or drain. If flooring is normal at www.whirlpool.com/product_help - Load could fall between washer drum and tub or may not be unbalanced or too large. Avoid ... during "Add Garment." Gurgling or humming Washer may make a humming sound with the floor and locked. You will lock unlock and lock again. The pump may be level to avoid potential leaks. This is uneven, a 3/4" (19 mm) piece of a cycle. Fill hose washers. Door opened after...
... suggested here or visit our website at certain stages of the cycle. Check floor for leaks or clogged sink or drain. If flooring is normal at www.whirlpool.com/product_help - Load could fall between washer drum and tub or may not be unbalanced or too large. Avoid ... during "Add Garment." Gurgling or humming Washer may make a humming sound with the floor and locked. You will lock unlock and lock again. The pump may be level to avoid potential leaks. This is uneven, a 3/4" (19 mm) piece of a cycle. Fill hose washers. Door opened after...
Use & Care Guide
Page 19
...items sticking through the drum holes. See "Secure the Drain Hose" in the pump or stuck between cycles. Do not seal the drain hose with Extra Rinse. Check that inlet valve screens are not reversed. Select DRAIN & SPIN to the standpipe. Your hot water tank... for load size recommendation for any water remaining in the standpipe, or is normal. 19 The door will unlock at www.whirlpool.com/product_help - To remove suds, cancel cycle. If you experience Possible causes Solution Washer not performing as expected (cont.) ...
...items sticking through the drum holes. See "Secure the Drain Hose" in the pump or stuck between cycles. Do not seal the drain hose with Extra Rinse. Check that inlet valve screens are not reversed. Select DRAIN & SPIN to the standpipe. Your hot water tank... for load size recommendation for any water remaining in the standpipe, or is normal. 19 The door will unlock at www.whirlpool.com/product_help - To remove suds, cancel cycle. If you experience Possible causes Solution Washer not performing as expected (cont.) ...