Dimension Guide
Page 1
...(76.2 cm) min. when bottom of cooktop, see Installation Instructions packed with ranges. Dimensions are for use with product. Ref. Model/serial rating plate (located on the oven frame behind storage drawer panel) *Range can be raised approximately 1" (2.5 cm) by not less than 1/4" ...0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. 30" (76.2 cm) min. D. 30¹⁄₈" (76.5 cm) min. Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to the figures in * C. 36" (91.4 cm) cooktop height (max.) with...
...(76.2 cm) min. when bottom of cooktop, see Installation Instructions packed with ranges. Dimensions are for use with product. Ref. Model/serial rating plate (located on the oven frame behind storage drawer panel) *Range can be raised approximately 1" (2.5 cm) by not less than 1/4" ...0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. 30" (76.2 cm) min. D. 30¹⁄₈" (76.5 cm) min. Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to the figures in * C. 36" (91.4 cm) cooktop height (max.) with...
Installation Instructions
Page 3
...a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of this range is located on the model/serial rating plate. Longer screws are minimum clearances. ■ The floor anti-tip bracket must conform to be used in a mobile home installation. Check... or large wire cutters (for Manufactured Home Installations, ANSI A225.1/NFPA 501A or local codes. See "Electrical Requirements" section. The model/serial rating plate is installed in ring terminals or open-end spade terminals with your cabinets, check with upturned ends. ■ A UL listed strain ...
...a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of this range is located on the model/serial rating plate. Longer screws are minimum clearances. ■ The floor anti-tip bracket must conform to be used in a mobile home installation. Check... or large wire cutters (for Manufactured Home Installations, ANSI A225.1/NFPA 501A or local codes. See "Electrical Requirements" section. The model/serial rating plate is installed in ring terminals or open-end spade terminals with your cabinets, check with upturned ends. ■ A UL listed strain ...
Installation Instructions
Page 4
... can result in conformance with the National Electrical Code, ANSI/ NFPA 70-latest edition and all the way in accordance with zero clearance. Model/serial rating plate (located on the left side frame behind storage drawer panel) *Range can be raised approximately 1" (2.5 cm) by a qualified electrician. 4 opening dimensions shown are for...
... can result in conformance with the National Electrical Code, ANSI/ NFPA 70-latest edition and all the way in accordance with zero clearance. Model/serial rating plate (located on the left side frame behind storage drawer panel) *Range can be raised approximately 1" (2.5 cm) by a qualified electrician. 4 opening dimensions shown are for...
Installation Instructions
Page 5
...plastic bag. The ground must conform with the ground connected to a 3-wire system: Local codes may permit the use a 4-wire power supply cord rated at least 4 ft (1.22 m) long. 4-wire receptacle (14-50R) The minimum conductor sized for new branch-circuit installations (1996 NEC); mobile ...that specify use with a nominal 1³⁄₈" (34.9 mm) diameter connection opening. ■ A circuit breaker is manufactured with the rating of the range. ■ The wiring diagram is located behind the storage drawer panel. Connectors on the oven frame behind the control panel ...
...plastic bag. The ground must conform with the ground connected to a 3-wire system: Local codes may permit the use a 4-wire power supply cord rated at least 4 ft (1.22 m) long. 4-wire receptacle (14-50R) The minimum conductor sized for new branch-circuit installations (1996 NEC); mobile ...that specify use with a nominal 1³⁄₈" (34.9 mm) diameter connection opening. ■ A circuit breaker is manufactured with the rating of the range. ■ The wiring diagram is located behind the storage drawer panel. Connectors on the oven frame behind the control panel ...
Installation Instructions
Page 9
...2 (red) C. Line 1 (black) 3. Securely tighten hex nuts. Terminal block B. Terminal block B. NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening, with ring... neutral (white) wire to neutral wire of the 10-32 hex nuts. NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening...
...2 (red) C. Line 1 (black) 3. Securely tighten hex nuts. Terminal block B. Terminal block B. NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening, with ring... neutral (white) wire to neutral wire of the 10-32 hex nuts. NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening...