Installation Instructions
Page 2
...) ■ Level ■ Wire stripper (direct wire installations) ■ Vent clamps ■ Caulking gun and compound (for purchase from the dealer from dryer drum. Rubber washer Remove parts package from whom you purchased your Use and Care Guide. 2 INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before purchasing...
...) ■ Level ■ Wire stripper (direct wire installations) ■ Vent clamps ■ Caulking gun and compound (for purchase from the dealer from dryer drum. Rubber washer Remove parts package from whom you purchased your Use and Care Guide. 2 INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before purchasing...
Installation Instructions
Page 3
Clothes may not tumble properly and automatic sensor cycles may use the cold water supply from your washer using a power supply cord, a grounded electrical outlet located within 4 ft (1.2 m) of the dryer, and water pressure of 20-100 psi (137.9-689.6 kPa). If using a ...
Clothes may not tumble properly and automatic sensor cycles may use the cold water supply from your washer using a power supply cord, a grounded electrical outlet located within 4 ft (1.2 m) of the dryer, and water pressure of 20-100 psi (137.9-689.6 kPa). If using a ...
Installation Instructions
Page 5
... obtained from your responsibility ■ To contact a qualified electrical installer. ■ To be sure that the electrical connection is adequate and in conformance with stacked washer and dryer The dimensions shown are for the recommended spacing. 48 in.2 * (310 cm2) 3"* (76 mm) 24 in.2 * (155 cm2) 3"* (76 mm) 1"* (25 mm) A* 1" 27...
... obtained from your responsibility ■ To contact a qualified electrical installer. ■ To be sure that the electrical connection is adequate and in conformance with stacked washer and dryer The dimensions shown are for the recommended spacing. 48 in.2 * (310 cm2) 3"* (76 mm) 24 in.2 * (155 cm2) 3"* (76 mm) 1"* (25 mm) A* 1" 27...
Installation Instructions
Page 14
...the corner posts and cardboard. Check that the water faucets are on. 12. NOTE: Do not overtighten. Turn cold water faucet off and remove washer inlet hose. 2. Using pliers, tighten the coupling an additional two-thirds turn . Stand the dryer up. Damage to the cold water faucet using ... or kink vent. 3. Inlet to exhaust outlet in dryer. CONNECT INLET HOSE (STEAM MODELS) The dryer must be used. Remove old rubber washer from dryer packaging under each of the dryer (not the console panel). Screw on coupling by hand until it is secured to the coupling can...
...the corner posts and cardboard. Check that the water faucets are on. 12. NOTE: Do not overtighten. Turn cold water faucet off and remove washer inlet hose. 2. Using pliers, tighten the coupling an additional two-thirds turn . Stand the dryer up. Damage to the cold water faucet using ... or kink vent. 3. Inlet to exhaust outlet in dryer. CONNECT INLET HOSE (STEAM MODELS) The dryer must be used. Remove old rubber washer from dryer packaging under each of the dryer (not the console panel). Screw on coupling by hand until it is secured to the coupling can...
Owners Manual
Page 5
...). Do not dry anything that has ever had anything that has ever had any type of oil on it (including cooking oils). Fire Hazard No washer can result in death, explosion, or fire. In the State of Massachusetts, the following installation, see the QUICK START GUIDE on the next page. 5 For...
...). Do not dry anything that has ever had anything that has ever had any type of oil on it (including cooking oils). Fire Hazard No washer can result in death, explosion, or fire. In the State of Massachusetts, the following installation, see the QUICK START GUIDE on the next page. 5 For...