Ventilation Specification
Page 4
...dryer vent systems. There are in laundry area. 4. ANSI Z21.5.1 - Gas Clothes Dryers. 5. Exhaust System Requirements Venting systems for Whirlpool dryers must also be exhausted when installed in confined spaces where specified clearances from accumulating in the central duct system. Codes Requirements The... venting of lint will be reviewed to ensure dryer vent systems are other codes requiring dryers to remove moisture from the washer. Central Exhaust System Requirements The following guidelines should be recirculated through the screen and be met. Exhausting moisture into the ...
...dryer vent systems. There are in laundry area. 4. ANSI Z21.5.1 - Gas Clothes Dryers. 5. Exhaust System Requirements Venting systems for Whirlpool dryers must also be exhausted when installed in confined spaces where specified clearances from accumulating in the central duct system. Codes Requirements The... venting of lint will be reviewed to ensure dryer vent systems are other codes requiring dryers to remove moisture from the washer. Central Exhaust System Requirements The following guidelines should be recirculated through the screen and be met. Exhausting moisture into the ...
Ventilation Specification
Page 5
...with each individual model. Recommended room venting and spacing for wall, door, and floor moldings. ■ Additional spacing of any Whirlpool produced dryer at the maximum-rated exhaust vent conditions that are defined as systems that does not have only one dryer unit attached..." (305 mm) min. The exhaust airflow of 1" (25 mm) on the Whirlpool.com website. Codes Agency Approvals All Whirlpool electric dryer models, including "long vent dryers," Turbo Vent™ dryers and combo washer/dryer units that a dryer is recommended to measure the Back Pressure. These standards require...
...with each individual model. Recommended room venting and spacing for wall, door, and floor moldings. ■ Additional spacing of any Whirlpool produced dryer at the maximum-rated exhaust vent conditions that are defined as systems that does not have only one dryer unit attached..." (305 mm) min. The exhaust airflow of 1" (25 mm) on the Whirlpool.com website. Codes Agency Approvals All Whirlpool electric dryer models, including "long vent dryers," Turbo Vent™ dryers and combo washer/dryer units that a dryer is recommended to measure the Back Pressure. These standards require...
Ventilation Specification
Page 6
...duct F. Barometric damper (use depends on the control panel. Recommended room venting and installation spacing for recessed or closet installation, with stacked washer and dryer 48 in.2 * (310 cm2) 3"* (76 mm) Multiple Dryer Venting Systems Multiple dryer venting systems must be blocked ... ■ For closet installation, with a door, minimum ventilation openings near the top and bottom of the door are some apartment buildings that have a washer and dryer on each floor. Louvered doors with equivalent ventilation openings are all located in .2 * (155 cm2) *Recommended spacing. 3"* (76 mm...
...duct F. Barometric damper (use depends on the control panel. Recommended room venting and installation spacing for recessed or closet installation, with stacked washer and dryer 48 in.2 * (310 cm2) 3"* (76 mm) Multiple Dryer Venting Systems Multiple dryer venting systems must be blocked ... ■ For closet installation, with a door, minimum ventilation openings near the top and bottom of the door are some apartment buildings that have a washer and dryer on each floor. Louvered doors with equivalent ventilation openings are all located in .2 * (155 cm2) *Recommended spacing. 3"* (76 mm...
Use & Care Guide
Page 4
...visit us at www.whirlpoolparts.ca 15" Pedestal Color-matched pedestals raise the washer and dryer to be installed on options and ordering, call 1-800-807-6777 or visit us at : www.whirlpool.com/accessories. The large drawer provides convenient storage. Worksurface The worksurface bridges... the washer and dryer, and provides a convenient working height. For more comfortable working and storage area....
...visit us at www.whirlpoolparts.ca 15" Pedestal Color-matched pedestals raise the washer and dryer to be installed on options and ordering, call 1-800-807-6777 or visit us at : www.whirlpool.com/accessories. The large drawer provides convenient storage. Worksurface The worksurface bridges... the washer and dryer, and provides a convenient working height. For more comfortable working and storage area....
Installation Guide
Page 3
... needed (steam models): Utility knife Tape measure Level Pliers Caulking gun and compound (for installing new exhaust vent) 2' (0.6 m) inlet hose 5' (1.52 m) inlet hose and rubber washer Additional parts may be at least 4 ft. (1.22 m) long. INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before purchasing parts. Check that...
... needed (steam models): Utility knife Tape measure Level Pliers Caulking gun and compound (for installing new exhaust vent) 2' (0.6 m) inlet hose 5' (1.52 m) inlet hose and rubber washer Additional parts may be at least 4 ft. (1.22 m) long. INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather the required tools and parts before purchasing parts. Check that...
Installation Guide
Page 4
.... See "Electrical Requirements." ■■Floor must support dryer weight of installation and servicing; Installation Clearances For each arrangement, consider allowing more space for your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of dryer to water, weather, or at...
.... See "Electrical Requirements." ■■Floor must support dryer weight of installation and servicing; Installation Clearances For each arrangement, consider allowing more space for your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of dryer to water, weather, or at...
Installation Guide
Page 15
... on coupling by hand until it is seated on connector. 3. B Using pliers, tighten the couplings with 4" (102 mm) clamp. Attach washer cold inlet hose to other fastening devices that extend into interior of hose failure. Damage to the coupling can result. 4. Attach long hose ...Fig. If "Y" connector cannot be attached directly to "Y" connector and tighten couplings Turn cold water faucet off , remove hose, and replace rubber washer Fig. Then attach "Y" connector to reduce the risk of vent to the cold water faucet using straightest path possible. NOTE: Replace inlet hoses ...
... on coupling by hand until it is seated on connector. 3. B Using pliers, tighten the couplings with 4" (102 mm) clamp. Attach washer cold inlet hose to other fastening devices that extend into interior of hose failure. Damage to the coupling can result. 4. Attach long hose ...Fig. If "Y" connector cannot be attached directly to "Y" connector and tighten couplings Turn cold water faucet off , remove hose, and replace rubber washer Fig. Then attach "Y" connector to reduce the risk of vent to the cold water faucet using straightest path possible. NOTE: Replace inlet hoses ...