Use & Care Guide
Page 4
...sweaters and tennis shoes. Stack Kit If space is at : www.whirlpool.com/accessories. In Canada, call 1-800-807-6777 or visit us at www.whirlpoolparts.ca 15" Pedestal Color-matched pedestals raise the washer and dryer to a more information on options and ordering, call 1-800...at a premium, the stack kit allows the dryer to be installed on top of the washer. 4 Drying Rack The Drying Rack provides a stationary drying surface for more information. Accessories Enhance your new washer and dryer with the following genuine Whirlpool accessories. The large drawer provides convenient storage.
...sweaters and tennis shoes. Stack Kit If space is at : www.whirlpool.com/accessories. In Canada, call 1-800-807-6777 or visit us at www.whirlpoolparts.ca 15" Pedestal Color-matched pedestals raise the washer and dryer to a more information on options and ordering, call 1-800...at a premium, the stack kit allows the dryer to be installed on top of the washer. 4 Drying Rack The Drying Rack provides a stationary drying surface for more information. Accessories Enhance your new washer and dryer with the following genuine Whirlpool accessories. The large drawer provides convenient storage.
Installation Guide
Page 3
... wire installations) Tin snips (new vent installations) 1/4" and 5/16" nut driver (recommended) Adjustable wrench that connect to 1" (25 mm) or hex-head socket wrench Rubber washer Parts package is located in your dryer. 3 The cord should contain: ■■A UL listed 30-amp power supply cord, rated 120/240 volt minimum...
... wire installations) Tin snips (new vent installations) 1/4" and 5/16" nut driver (recommended) Adjustable wrench that connect to 1" (25 mm) or hex-head socket wrench Rubber washer Parts package is located in your dryer. 3 The cord should contain: ■■A UL listed 30-amp power supply cord, rated 120/240 volt minimum...
Installation Guide
Page 4
... dryer at temperatures below 40° F (4° C). You may cause dryer not to reduce noise transfer. Lower temperatures may use the water supply for your washer using the supplied "Y" connector and a short hose (which you will need : ■■A location allowing for exhaust vent with maximum slope of 5" (127 mm) clearance...
... dryer at temperatures below 40° F (4° C). You may cause dryer not to reduce noise transfer. Lower temperatures may use the water supply for your washer using the supplied "Y" connector and a short hose (which you will need : ■■A location allowing for exhaust vent with maximum slope of 5" (127 mm) clearance...
Installation Guide
Page 15
.... Tighten couplings Vent must be connected to "Y" connector and tighten couplings Turn cold water faucet off , remove hose, and replace rubber washer Using pliers, tighten the couplings with additional two-thirds turn . Use clamps to cold water faucet. The dryer must fit over the ... or other side of vent to other fastening devices that extend into interior of "Y" connector. Secure vent to "Connect Vent." Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. Using pliers, tighten the couplings an additional two-thirds turn . Install Vent System...
.... Tighten couplings Vent must be connected to "Y" connector and tighten couplings Turn cold water faucet off , remove hose, and replace rubber washer Using pliers, tighten the couplings with additional two-thirds turn . Use clamps to cold water faucet. The dryer must fit over the ... or other side of vent to other fastening devices that extend into interior of "Y" connector. Secure vent to "Connect Vent." Remove old rubber washer from inlet hose and replace with 4" (102 mm) clamp. Using pliers, tighten the couplings an additional two-thirds turn . Install Vent System...