Installation Guide
Page 4
... a power supply cord: Use a UL listed power supply cord kit marked for installing new exhaust vent) 1/4"( 6 mm) nut driver (recommended) "Y" connector Short inlet hose Rubber washer Parts package is located in ring terminals or spade terminals with any tools listed here. The cord should contain: ■■ A UL listed 30-amp...
... a power supply cord: Use a UL listed power supply cord kit marked for installing new exhaust vent) 1/4"( 6 mm) nut driver (recommended) "Y" connector Short inlet hose Rubber washer Parts package is located in ring terminals or spade terminals with any tools listed here. The cord should contain: ■■ A UL listed 30-amp...
Installation Guide
Page 5
... "Venting Requirements" before purchasing parts. Space must support dryer weight of companion appliance. ■■ Level floor with dryer) Refer to fully open. Contact your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of 1" (25 mm) under entire dryer. Mobile...
... "Venting Requirements" before purchasing parts. Space must support dryer weight of companion appliance. ■■ Level floor with dryer) Refer to fully open. Contact your washer using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of 1" (25 mm) under entire dryer. Mobile...
Installation Guide
Page 18
... mobile home and must not terminate beneath the mobile home. Secure vent to the charts. 18 Turn cold water faucet off , remove and replace rubber washer 0 Rigid metal 64 ft. (20 m) 1 Rigid metal 54 ft. (16.5 m) 2 Rigid metal 44 ft. (13.4 m) 3 Rigid metal 35 ft. (10.7 m) 4... Rigid metal 27 ft. (8.2 m) NOTE: Bottom exhaust installations have a 90° turn to exhaust hood with new rubber washer. The dryer must fit over the exhaust hood. Avoid 90° turns. Do not use caulking compound to seal exterior wall opening around exhaust hood...
... mobile home and must not terminate beneath the mobile home. Secure vent to the charts. 18 Turn cold water faucet off , remove and replace rubber washer 0 Rigid metal 64 ft. (20 m) 1 Rigid metal 54 ft. (16.5 m) 2 Rigid metal 44 ft. (13.4 m) 3 Rigid metal 35 ft. (10.7 m) 4... Rigid metal 27 ft. (8.2 m) NOTE: Bottom exhaust installations have a 90° turn to exhaust hood with new rubber washer. The dryer must fit over the exhaust hood. Avoid 90° turns. Do not use caulking compound to seal exterior wall opening around exhaust hood...
Installation Guide
Page 19
... couplings an additional two-thirds turn . Damage to cold water faucet. Check for leaks around "Y" connector, faucets, and hoses. 19 NOTE: Do not overtighten. Attach washer cold inlet hose to other end of long hose to "Y" connector and tighten couplings Check that the water faucet is seated on . 7. 2. Attach long hose...
... couplings an additional two-thirds turn . Damage to cold water faucet. Check for leaks around "Y" connector, faucets, and hoses. 19 NOTE: Do not overtighten. Attach washer cold inlet hose to other end of long hose to "Y" connector and tighten couplings Check that the water faucet is seated on . 7. 2. Attach long hose...
Dimension Guide
Page 1
... mm) Bottom view 113/8" 35/8" (289 mm) (93 mm) 3" 13/8" 141/2" (77 mm) (35 mm) (370 mm) 31/2" (93 mm) NOTE: Leveling legs 1/2" (13 mm) (3.6 washer capacity) or 1½" (38 mm) (3.8 washer capacity) depending model. See "Venting Requirements."
... mm) Bottom view 113/8" 35/8" (289 mm) (93 mm) 3" 13/8" 141/2" (77 mm) (35 mm) (370 mm) 31/2" (93 mm) NOTE: Leveling legs 1/2" (13 mm) (3.6 washer capacity) or 1½" (38 mm) (3.8 washer capacity) depending model. See "Venting Requirements."
