English Manual
Page 2
... IP, Inc. 2 TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 ASSEMBLY 6 OPERATION AND ADJUSTMENT 9 HOW TO FOLD AND MOVE THE TREADMILL 15 TROUBLESHOOTING 16 EXERCISE GUIDELINES 19 PART LIST 20 EXPLODED DRAWING 21 ORDERING REPLACEMENT PARTS Back Cover LIMITED ...WARRANTY Back Cover WARNING DECAL PLACEMENT This drawing shows the location(s) of this manual and request a free replacement decal. WESLO is ...
... IP, Inc. 2 TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 ASSEMBLY 6 OPERATION AND ADJUSTMENT 9 HOW TO FOLD AND MOVE THE TREADMILL 15 TROUBLESHOOTING 16 EXERCISE GUIDELINES 19 PART LIST 20 EXPLODED DRAWING 21 ORDERING REPLACEMENT PARTS Back Cover LIMITED ...WARRANTY Back Cover WARNING DECAL PLACEMENT This drawing shows the location(s) of this manual and request a free replacement decal. WESLO is ...
English Manual
Page 4
Never leave the treadmill unattended while it is properly assembled. (See ASSEMBLY on page 6 and HOW TO FOLD AND MOVE THE TREADMILL on page 15.) You must be performed by an authorized ser- SAVE THESE INSTRUCTIONS 4 Always unplug the power cord immediately after use, before performing the ...
Never leave the treadmill unattended while it is properly assembled. (See ASSEMBLY on page 6 and HOW TO FOLD AND MOVE THE TREADMILL on page 15.) You must be performed by an authorized ser- SAVE THESE INSTRUCTIONS 4 Always unplug the power cord immediately after use, before performing the ...
English Manual
Page 6
...the Upright. Orient the Base (80) as shown. To avoid damaging parts, do not dispose of the treadmill. Attach the Base to identify the assembly hardware. do not use power tools for assembly. Note: After shipping, there may be included. 4.2 x 19mm Screw (3)-6 #10 x 1" Tek Screw (...73), so that the power cord is completed. Assembly requires two persons. The number after the parentheses is normal. ASSEMBLY To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480. and needle- Assembly requires the included hex keys and your own Phillips...
...the Upright. Orient the Base (80) as shown. To avoid damaging parts, do not dispose of the treadmill. Attach the Base to identify the assembly hardware. do not use power tools for assembly. Note: After shipping, there may be included. 4.2 x 19mm Screw (3)-6 #10 x 1" Tek Screw (...73), so that the power cord is completed. Assembly requires two persons. The number after the parentheses is normal. ASSEMBLY To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480. and needle- Assembly requires the included hex keys and your own Phillips...
English Manual
Page 7
... (71). Connect the Upright Wire (71) to the Upright (73) with four M10 x 45mm Screws (2). 2. Attach the Handrails (69) to the console wire. Console Assembly 71 Console Wire Console Wire 71 73 Tie 7 Start all four 2 Screws, and then tighten them. 2 69 69 2 73 3. With the help of a second person..., hold the console assembly near the Upright (73). Insert the connectors and the excess wire into place. If they do not, turn one connector and try again.
... (71). Connect the Upright Wire (71) to the Upright (73) with four M10 x 45mm Screws (2). 2. Attach the Handrails (69) to the console wire. Console Assembly 71 Console Wire Console Wire 71 73 Tie 7 Start all four 2 Screws, and then tighten them. 2 69 69 2 73 3. With the help of a second person..., hold the console assembly near the Upright (73). Insert the connectors and the excess wire into place. If they do not, turn one connector and try again.
English Manual
Page 8
Console Assembly 73 69 3 3 69 3 5. Attach the Latch Housing (72) to the left Upright (73) with six M4.2 x 19mm 4 Screws (3). To protect the floor or carpet, place a mat under the treadmill. 8 Be careful not to adjust the walking belt (see pages 17 and 18). start 5 both Screws, and then... tighten them. 73 72 83 6. Make sure that all parts are properly tightened before you use the treadmill. 4. Attach the console assembly to the Upright (73) and the Handrails (69) with two #10 x 1" Tek Screws (83); Keep the included hex keys in a ...
Console Assembly 73 69 3 3 69 3 5. Attach the Latch Housing (72) to the left Upright (73) with six M4.2 x 19mm 4 Screws (3). To protect the floor or carpet, place a mat under the treadmill. 8 Be careful not to adjust the walking belt (see pages 17 and 18). start 5 both Screws, and then... tighten them. 73 72 83 6. Make sure that all parts are properly tightened before you use the treadmill. 4. Attach the console assembly to the Upright (73) and the Handrails (69) with two #10 x 1" Tek Screws (83); Keep the included hex keys in a ...