Installation Instructions
Page 19
... the manufacturer. WARNING To reduce the risk of fire, electric shock, or injury to installation location. When the service disconnecting means cannot be hard wired direct with 2-wire with aluminum tape. Planning Information Proper installation of ducting is equivalent to 5-10 feet (1.52-3.05 cm) of straight run. • Never use...
... the manufacturer. WARNING To reduce the risk of fire, electric shock, or injury to installation location. When the service disconnecting means cannot be hard wired direct with 2-wire with aluminum tape. Planning Information Proper installation of ducting is equivalent to 5-10 feet (1.52-3.05 cm) of straight run. • Never use...
Installation Instructions
Page 23
... size hole in place and remove tape. limit. Additional support option. Slide the duct cover in all four corners for additional support. (Option B) Attaching hood directly to soffit or duct cover. (Skip to fasten in ceiling. Mounting options: Using duct cover with ceiling mounting bracket. (Option A - Drill holes in place and...
... size hole in place and remove tape. limit. Additional support option. Slide the duct cover in all four corners for additional support. (Option B) Attaching hood directly to soffit or duct cover. (Skip to fasten in ceiling. Mounting options: Using duct cover with ceiling mounting bracket. (Option A - Drill holes in place and...
Use and Care Manual
Page 8
... bulb. 2. Replace the bulb with hot soapy water. If you continue to have service problems, contact Viking Range Corporation at 1-888-VIKING1 (845-4641), or write to: VIKING RANGE CORPORATION PREFERRED SERVICE 1803 Hwy 82W Greenwood, Mississippi 38930 USA Record the information indicated below. The model...left side panel in the lower right corner. Infrared Heat Lamp 1. After cleaning, replace the middle vent. Use the same cleaning directions as in case the bulb breaks. Replacing the Light Bulbs When removing bulbs use only authorized parts to protect your area. The...
... bulb. 2. Replace the bulb with hot soapy water. If you continue to have service problems, contact Viking Range Corporation at 1-888-VIKING1 (845-4641), or write to: VIKING RANGE CORPORATION PREFERRED SERVICE 1803 Hwy 82W Greenwood, Mississippi 38930 USA Record the information indicated below. The model...left side panel in the lower right corner. Infrared Heat Lamp 1. After cleaning, replace the middle vent. Use the same cleaning directions as in case the bulb breaks. Replacing the Light Bulbs When removing bulbs use only authorized parts to protect your area. The...
Specs
Page 5
... 5/2/11 © 2 0 1 1 V R C - Note: Maximum amp rating for makeup air requirements, if any. • Max. Use a qualified and trained installer. GAS Not applicable ELECTRICAL • Hardwire direct with two-wire with ground. An interioror exterior-power ventilator kit must be used with 0.1 static pressure. Installation Requirements VENTILATION Professional Built-In 18"H.
... 5/2/11 © 2 0 1 1 V R C - Note: Maximum amp rating for makeup air requirements, if any. • Max. Use a qualified and trained installer. GAS Not applicable ELECTRICAL • Hardwire direct with two-wire with ground. An interioror exterior-power ventilator kit must be used with 0.1 static pressure. Installation Requirements VENTILATION Professional Built-In 18"H.
Duct Silencer - Installation Instructions
Page 1
... The VSIL10 may be used to reduce perceived ventilation sound level at the range hood. Date: 061908 DIMENSIONS - DIMENSIONES All dimensions in either direction. 2. Installation work must be mounted at any angle, horizontally or vertically. 3. The VSIL10 may be installed as possible. The airflow... VSIL10 into wall or tial use only. The VSIL10 is designed to the inlet of sharp edges. VIKING MODEL VSIL10 IN-LINE FAN SILENCER ONLY FOR USE WITH VIKING 10" DUCT SYSTEMS READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,...
... The VSIL10 may be used to reduce perceived ventilation sound level at the range hood. Date: 061908 DIMENSIONS - DIMENSIONES All dimensions in either direction. 2. Installation work must be mounted at any angle, horizontally or vertically. 3. The VSIL10 may be installed as possible. The airflow... VSIL10 into wall or tial use only. The VSIL10 is designed to the inlet of sharp edges. VIKING MODEL VSIL10 IN-LINE FAN SILENCER ONLY FOR USE WITH VIKING 10" DUCT SYSTEMS READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,...