Installation Instructions
Page 19
... installation location. Slide duct over and remove electrical box cover. amp rating for the most common installations are shown. all products must be hard wired direct with 2-wire with ground. It may vary depending on proper ducting; Wall Hoods w/Standard Ventilator) 1 2 4 5/16" nut driver Check damper for example, each 90º...
... installation location. Slide duct over and remove electrical box cover. amp rating for the most common installations are shown. all products must be hard wired direct with 2-wire with ground. It may vary depending on proper ducting; Wall Hoods w/Standard Ventilator) 1 2 4 5/16" nut driver Check damper for example, each 90º...
Installation Instructions
Page 23
... bracket. (Option A - Either 7" or 10" depending on your specific unit and ventillator kit. Drill holes in all four corners for additional support. (Option B) Attaching hood directly to soffit or duct cover. (Skip to ceiling. 45 NOTE: 200 lb. A2 B1 5/16" nut driver Attach duct cover to optional ceiling mounting bracket...
... bracket. (Option A - Either 7" or 10" depending on your specific unit and ventillator kit. Drill holes in all four corners for additional support. (Option B) Attaching hood directly to soffit or duct cover. (Skip to ceiling. 45 NOTE: 200 lb. A2 B1 5/16" nut driver Attach duct cover to optional ceiling mounting bracket...
Use and Care Manual
Page 8
...service agency, or if you are unable to obtain the name of parts, use an oven mitt to : VIKING RANGE CORPORATION PREFERRED SERVICE 1803 Hwy 82W Greenwood, Mississippi 38930 USA Record the information indicated below. You will not ...do the job, use every day household cleaners that you continue to have service problems, contact Viking Range Corporation at 1-888-VIKING1 (845-4641), or write to protect your hood is located behind the baffle...required, call your dealer or authorized service agency. Use the same cleaning directions as in "Cleaning the Hood Canopy" section. 3.
...service agency, or if you are unable to obtain the name of parts, use an oven mitt to : VIKING RANGE CORPORATION PREFERRED SERVICE 1803 Hwy 82W Greenwood, Mississippi 38930 USA Record the information indicated below. You will not ...do the job, use every day household cleaners that you continue to have service problems, contact Viking Range Corporation at 1-888-VIKING1 (845-4641), or write to protect your hood is located behind the baffle...required, call your dealer or authorized service agency. Use the same cleaning directions as in "Cleaning the Hood Canopy" section. 3.
Specs
Page 5
.../ducting is extremely important to 5' - 10' (1.52 - 3.05 cm) of straight run length is equivalent to ensure maximum performance. GAS Not applicable ELECTRICAL • Hardwire direct with two-wire with 0.1 static pressure. duct run o For 300 - 1,200 CFM-50' (15.2 m) o For 1,500 CFM-75' (22.9 m) o Duct run . • 7" round duct for...
.../ducting is extremely important to 5' - 10' (1.52 - 3.05 cm) of straight run length is equivalent to ensure maximum performance. GAS Not applicable ELECTRICAL • Hardwire direct with two-wire with 0.1 static pressure. duct run o For 300 - 1,200 CFM-50' (15.2 m) o For 1,500 CFM-75' (22.9 m) o Duct run . • 7" round duct for...
Duct Silencer - Installation Instructions
Page 1
... this particular application the VSIL10 should be in either direction. 2. The airflow through the VSIL10 can be located between the fan inlet and the range hood. VIKING MODEL VSIL10 IN-LINE FAN SILENCER ONLY FOR USE WITH VIKING 10" DUCT SYSTEMS READ AND SAVE THESE INSTRUCTIONS WARNING... should be adequately supported by qual- Again the VSIL10 may be done by using hanging straps or framing. 3. The VSIL10 is a non-directional device. When cutting or drilling into the 10" duct system. trical wiring or other hidden utilites. ceiling, take care not to be mounted...
... this particular application the VSIL10 should be in either direction. 2. The airflow through the VSIL10 can be located between the fan inlet and the range hood. VIKING MODEL VSIL10 IN-LINE FAN SILENCER ONLY FOR USE WITH VIKING 10" DUCT SYSTEMS READ AND SAVE THESE INSTRUCTIONS WARNING... should be adequately supported by qual- Again the VSIL10 may be done by using hanging straps or framing. 3. The VSIL10 is a non-directional device. When cutting or drilling into the 10" duct system. trical wiring or other hidden utilites. ceiling, take care not to be mounted...