Outdoor Products
Page 44
....5 cm) 28" (71.1 cm) 33 3/4" (85.7 cm) 9 1/4" (23.5 cm) 23 3/8" (59.4 cm) minimum 120VAC/60Hz - Unit must be ordered Natural or LP/Propane - hard wire direct with separate 15-amp minimum 2-wire with a Type 1, QCC-1 connector. LP/Propane cylinder with ground circuit (VEWD only) 3.6 amps/425 watts (VEWD only) 3.8 amps/450...
....5 cm) 28" (71.1 cm) 33 3/4" (85.7 cm) 9 1/4" (23.5 cm) 23 3/8" (59.4 cm) minimum 120VAC/60Hz - Unit must be ordered Natural or LP/Propane - hard wire direct with separate 15-amp minimum 2-wire with a Type 1, QCC-1 connector. LP/Propane cylinder with ground circuit (VEWD only) 3.6 amps/425 watts (VEWD only) 3.8 amps/450...
Outdoor Kitchen Planning Guide
Page 12
... a non-combustible surface (such as a brick wall). The 4"W. IMPORTANT: When using a VCF90, do not install a warming drawer base cabinet directly adjacent to account for the void area underneath the countertop that 8" is used as the back panel. 4) Use the 4"W. VBPFLR4 (stainless facing...is a 4"W., 341¼2"H. (includes 41¼2" toe kick area) stainless steel "post" sandwiched between two cabinets. 1) Use a 4"W. PLANNING YOUR VIKING OUTDOOR KITCHEN *Please note: If a VFLR4 is used in an island setting, a VBPFLR4 is required for proper installation of the rotisserie motor on page...
... a non-combustible surface (such as a brick wall). The 4"W. IMPORTANT: When using a VCF90, do not install a warming drawer base cabinet directly adjacent to account for the void area underneath the countertop that 8" is used as the back panel. 4) Use the 4"W. VBPFLR4 (stainless facing...is a 4"W., 341¼2"H. (includes 41¼2" toe kick area) stainless steel "post" sandwiched between two cabinets. 1) Use a 4"W. PLANNING YOUR VIKING OUTDOOR KITCHEN *Please note: If a VFLR4 is used in an island setting, a VBPFLR4 is required for proper installation of the rotisserie motor on page...
Use and Care Manual
Page 2
... leave these instructions with the consumer for future reference. • ALWAYS connect CO2 gas cylinder to reducing valve or regulator. • NEVER connect gas cylinder directly to reduce the chance of injury, and tell you and others is the safety alert symbol. This symbol alerts you to the cylinder. Table of...
... leave these instructions with the consumer for future reference. • ALWAYS connect CO2 gas cylinder to reducing valve or regulator. • NEVER connect gas cylinder directly to reduce the chance of injury, and tell you and others is the safety alert symbol. This symbol alerts you to the cylinder. Table of...
Use and Care Manual
Page 4
... open and clear of any circumstances, be cut or removed. Installation Location & Wiring BUILT-IN INSTALLATION Select Location The proper location will be out of direct sunlight and away from the bottom front section of the unit. Unit should be done with fan cooled condensers can be operated in . This should...
... open and clear of any circumstances, be cut or removed. Installation Location & Wiring BUILT-IN INSTALLATION Select Location The proper location will be out of direct sunlight and away from the bottom front section of the unit. Unit should be done with fan cooled condensers can be operated in . This should...
Use and Care Manual
Page 9
... unit. preferably around 38°F (3.3°C). Place the glass at the bottom front of the cabinet, just behind the square opening near the front of direct sunlight. • Do not splash or spray water on ambient temperature.) Initially set for your appliance's condenser periodically to become wild, turn sour and cloudy...
... unit. preferably around 38°F (3.3°C). Place the glass at the bottom front of the cabinet, just behind the square opening near the front of direct sunlight. • Do not splash or spray water on ambient temperature.) Initially set for your appliance's condenser periodically to become wild, turn sour and cloudy...
Use and Care Manual
Page 10
... cooling depends on top of cold keg Contaminated air source Dirty glasses Sluggish regulator Applied pressure is set too high Hot spots in front of direct sunlight. 3. To access the condenser, the unit must be washed with mild soap and water and thoroughly rinsed with other appliances.) 5. Set the control to...
... cooling depends on top of cold keg Contaminated air source Dirty glasses Sluggish regulator Applied pressure is set too high Hot spots in front of direct sunlight. 3. To access the condenser, the unit must be washed with mild soap and water and thoroughly rinsed with other appliances.) 5. Set the control to...