What Is A Tripp Lite Used For

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 4
... • The batteries contain chemical substances that should be blocked or covered. Liquid is required to take adequate measures. • Use of this equipment in a well-ventilated indoor area, away from the mains. To ensure reliable operation of electric shock and high ... THESE INSTRUCTIONS This manual contains instructions and warnings that may cause radio interference, in this equipment can reasonably be performed by Tripp Lite. The released electrolyte is disconnected from excess moisture, heat, dust, flammable gas or explosives. Failure to properly dispose of the...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 6
[email protected] for installation. 6 Examine if any installation and wiring. The balance supports have been locked on the top of the accessories using the original packing 4 material that came with internal batteries) 2 Owner's Manual 3 Test Card 4 RS-232 Cable SUT20K 1 pc. 1 pc. ... pc. 1 pc. (Male) (Female) SUT30K 1 pc. 1 pc. 1 pc. 1 pc. Please contact your local contact, go to activate the SmartOnline SUT warranty. Keep them well maintained after unpacking, as it may be necessary to be returned to Tripp Lite in order to www.tripplite.com/support/contacts and...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 7
... connect it may be moved sideways. If the device indicates there has been excessive shock or tilt, do not move the UPS cabinet using a forklift or other non-combustible surfaces only. • Install a CO2 or dry powder extinguisher in an environment with the aid of... a forklift. Installation and Wiring 3.2 Transportation WARNING The UPS is equipped with four balance supports. do not install and contact your local Tripp Lite representative. 3.4 Installation Environment • The UPS is fixed on concrete or other equipment to avoid accidents. If moving the UPS to ...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 8
... There are two installation methods. One is without the balance supports. Installation without the Balance Supports After moving the UPS to its final installation area, use the levelers to stabilize the UPS cabinet on the ground. (Figure 3-1: Stabilize the UPS with Levelers) Installation with the balance supports and the other is...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 9
M6 Screw x 8 Balance Support x 4 (Figure 3-3: Balance Support Installation) 3 Use four user-supplied M8 bolts to fix the four balance supports on the ground to the figure below. Refer to avoid UPS movement. Balance Support x 4 Ground M8 Bolts x 4 (Figure 3-4: Fix the Balance Supports on the UPS. 3. Installation and Wiring 2 Place the UPS over the drilled holes, use the levelers to stabilize the UPS on the ground and use the M6 screws to reinstall the balance supports (that were removed from the UPS during the unpacking process) on the Ground) 9

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 10
...input and output of the UPS input side and the UPS neutral (N) be three phases (R/S/T) and meet safety certifications. UPS System SUT20K SUT30K SUT40K SUT60K Recommended Protective Device D-Curve 75A circuit breaker D-Curve 125A circuit breaker D-Curve 150A circuit breaker D-Curve 225A circuit breaker •...Prior to the following table for wiring. 10 lb. (14.7 N·m) 75A (3-pole x 1) SUT30K 1/0 AWG (50 mm2) 1/0 AWG (50 mm2) 1/0 AWG (50 mm2) 130 in . lb. (14.7 N·m) 225A (3-pole x 1) * Use only copper wire rated to the UPS is in front of the UPS is completely cut off...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 14
... the parallel UPS systems can be paralleled; If the symbol '!' 3. appears after an ID number, it indicates there is properly grounded (refer to Figures 3-6~3-10). 3 Use the provided parallel cable to connect the parallel ports on the parallel units. Communication Interfaces to the wiring terminal block and ensure the UPS system...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 15
This guarantees that the UPS can provide sufficient backup power to the UPS only after the batteries are fully charged. When using both the UPS internal batteries and external batteries, ensure the voltage difference is 3. Installation and Wiring 3.7 External Battery Cabinet Connection Precautions WARNING: 1. Connect loads to the loads connected when a power failure occurs. 2.

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 17
... UPS systems can connect with common batteries. Servicing of electric shock and high short-circuit current. however, if paralleling UPS systems for redundancy, Tripp Lite does not recommend the use an AC breaker. Refer to the batteries. External Battery Cabinet ( ) External Battery Cabinet ( ) External Battery Cabinet Fast-acting Fuses 4-pole Non-fuse DC...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 19
...Only qualified service personnel should perform battery installation, wiring and connection. 4. START UP and COMMISSIONING An authorized Tripp Lite engineer must perform the start-up of the UPS and a completed start-up form must be returned to...SUT30K Front View with Door Open and Battery Compartment Panel Removed.) (Figure 4-5: SUT40K Front View with Door Open and Battery Compartment Panel Removed.) 2 Input Breaker Controls the UPS system's main input switch and is used for more information. 1. The internal batteries, battery trays and battery cables shown in order to Tripp Lite...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 22
For more information, contact Tripp Lite. Connects to 6. Communication Interfaces. 9 REPO Port When an emergency event occurs, the UPS immediately disconnects the power supply and shuts down the unit. For detailed information, refer to a computer. Do not use the casters to 6. Item 1 SMART Slot 2 MINI Slot 3 Parallel Ports 4 Parallel Switch 5 RS-232 Port Description...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 26
... off the middle UPS DIP switches and turn on each UPS DIP switch. 2. Enables/disables audible alerts. 4. The Relay I/O or MODBUS card may be coupled using the provided parallel cable to run in this slot to the following diagram: 1 2 3 4 5 98 7 6 (Figure 6-1: Communication Interfaces) Notes: 1. Hardware 1) ... When four UPS systems are paralleled, turn off the middle two DIP switches and turn on the remaining DIP switches. Use Tripp Lite's free PowerAlert® power management software (available for UPS parallel communication. 6. Sets shutdown delay time. 3.

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 27
...power to the table below. Default: Pins 9 and 10. 1. In the process of setup limit. 2. 6. The dry contacts are eighteen selectable events, six may be used to check and monitor the UPS status via a computer. 6 Output Dry Contacts P1 P2 P3 P4 P5 P6 Pin 1 2 3 4 5 6 7 8 9 ... in Bypass Mode. 2. The bypass voltage, frequency or phase sequence is lower than setup limit, 220V DC. 2. A user-supplied USB cable and Tripp Lite's free PowerAlert® power management software (available for download at www.tripplite.com/poweralert) can be selected. Please refer to the connected load. 2....

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 29
As shown in the diagram below, there are two signal sources. 6. With this port, the UPS can detect the operating status of the external charger box and control its switch. One signal source controls the on/off charging mechanism and the other signal source detects the charging status (fail/no fail). 29 Communication Interfaces 9 Charger Detection Port The charger detection port is used to connect with an external charger box.

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 33
... While in Bypass Mode. 8. Press and hold for 3 seconds. The default setting of BYPASS SETUP can be modified when the UPS is 5~15%. Use function keys ( ), ( ) and ( ) to set the DATE, TIME and PASSWORD. 2. Bypass Setup Route: Main Screen  Setting ... BYPASS MENU The range of FREQ RANGE is 0000 Use function keys ( ), ( ) and ( ) to change the UPS system's local, bypass, output, charger, battery, battery test, control & test, parallel and advanced ...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 34
...is 163. The default setting is 50 Hz. VOLT (V): The UPS system's output voltage when in a configuration. There are : SUT20K 5A SUT30K 7.5A SUT40K 7.5A SUT60K 10A CHARGE FLOAT VOLT(V): Sets the floating voltage. The default setting is OFF. The default setting is OFF. REDUNDANCY... Display and Settings 3. CHARGE CURRENT: The charge current range is 120V. FREQ (HZ): The UPS system's output frequency when in Normal (On-line) Mode. Use function keys ( ), ( ) and ( ) to the second screen. The default setting is 1A~20A. Output Setup Route: Main Screen  Setting &#...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 35
... 5. Replace Date (Y-M-D): Battery's replacement date. The default setting is 120V. SHUTDOWN VOLT (V): The default setting is SUT20K: 20AH, SUT30K and SUT40K: 30AH, SUT60K: 40AH. Install Date (Y-M-D): Battery's actual install date. Manual Test: Initiates the start of a battery manual...default setting is pass. TYPE (AH): Sets the battery rating. If above, the result is 144. Do not change the BATTERY SETUP setting. 6. Use function keys ( ), ( ) and ( ) to change or initiate the BATTERY TEST setting. 35 8. Battery Test Route: Main Screen  ...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 36
... ADVANCED CLEAR STATISTICS: Includes RUN TIME, ON BAT COUNTS, ON BYPASS COUNTS, and TOTAL EVENT COUNTS. There are two choices to upgrade: PFC and SYSTEM Use function keys ( ), ( ) and ( ) to change the PARALLEL ID to enter into the Parallel • ID: In parallel mode, this is ...in a parallel configuration, you can clear statistics of PARALLEL ID. 9. LCD Display and Settings 7. The default setting is YES. The default setting is ON. Use function keys ( ), ( ) and ( ) to ON, the UPS will shut down and automatically restart. If set to change the setting of all the ...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 37
..., inverter, output, battery, temperature and DC BUS readings. User can set up the last two items. 8.5 Measure Route: Main Screen  Main Menu  Measure Use the function keys ( ) and ( ) to enter the Main Menu. 1.MEASURE 2.MAINTENANCE MEASURE Check the UPS mains, bypass, inverter, output, battery, temperature and DC BUS readings...

Owner s Manual for SmartOnline r SUT 3-Phase UPS System 20/30/40/60kVA 933631 Multi-language

Page 38
... UPS total number of stored events is shown as an example only; LCD Display and Settings 8.6 Maintenance Route: Main Screen  Main Menu  Maintenance Use the function keys ( ) and ( ) to the prior screen. RUN TIME (DD HH: MM: SS): The UPS total running time. 2. The maximum number of logged events...

What Is A Tripp Lite Used For - SUT30K