Installation Guide for SNMPWEBCARD 933179
Page 3
Static IP Address Assignment. If you are nearly even with the guides in Accessory Slot: Use a screwdriver to the card by default to 4 -Test and Configure. The card can be identified on , align the SNMPWEBCARD with the rear surface of firmware version 12.06.006X, the SNMPWEBCARD ...cable to the RJ-45 Ethernet port on the card. Installation 1-4 Address Assignment: If your network's DHCP server will assign a dynamic IP address to the SNMPWEBCARD automatically, proceed to its MAC address (see Step 1-3 ). Note: This port does not support PoE (Power over Ethernet) applications. ...
Static IP Address Assignment. If you are nearly even with the guides in Accessory Slot: Use a screwdriver to the card by default to 4 -Test and Configure. The card can be identified on , align the SNMPWEBCARD with the rear surface of firmware version 12.06.006X, the SNMPWEBCARD ...cable to the RJ-45 Ethernet port on the card. Installation 1-4 Address Assignment: If your network's DHCP server will assign a dynamic IP address to the SNMPWEBCARD automatically, proceed to its MAC address (see Step 1-3 ). Note: This port does not support PoE (Power over Ethernet) applications. ...
Installation Guide for SNMPWEBCARD 933179
Page 7
...: Obtain IPv4 settings automatically using DHCP for Ethernet interface? [Y] IP address? [10.1.0.165] Subnet mask? [255.0.0.0] Gateway address?...domain? [tlsoftwaredev.local] 3-5-2 Network Service Configuration The following prompts configure the connection methods that the SNMPWEBCARD will wait 5 seconds Press any key in GMT: 03/13/2012 18:19:51 This ... M to Modify?m Enter the root password: ********* 3-5-1 Network Settings Follow the prompts to change these settings. The default terminal mode password is reset, start-up code will accept. Enable SNTP? [Y] Enable FTP? [Y] Port number? ...
...: Obtain IPv4 settings automatically using DHCP for Ethernet interface? [Y] IP address? [10.1.0.165] Subnet mask? [255.0.0.0] Gateway address?...domain? [tlsoftwaredev.local] 3-5-2 Network Service Configuration The following prompts configure the connection methods that the SNMPWEBCARD will wait 5 seconds Press any key in GMT: 03/13/2012 18:19:51 This ... M to Modify?m Enter the root password: ********* 3-5-1 Network Settings Follow the prompts to change these settings. The default terminal mode password is reset, start-up code will accept. Enable SNTP? [Y] Enable FTP? [Y] Port number? ...
Installation Guide for SNMPWEBCARD 933179
Page 10
default=rw, security=none indicates that the user has rw access to every facility, but due to the addition of the security facility tag, the user ... To allow anybody with an address of the program. For Example: default=rw indicates the user has read write access to these facilities are rw, ro or none. Allowed IP address or Address range, v6 or tunneled v4, "::" means any address IP address Mask in v6 notation, "::" means any IPv4 Example: To allow...
default=rw, security=none indicates that the user has rw access to every facility, but due to the addition of the security facility tag, the user ... To allow anybody with an address of the program. For Example: default=rw indicates the user has read write access to these facilities are rw, ro or none. Allowed IP address or Address range, v6 or tunneled v4, "::" means any address IP address Mask in v6 notation, "::" means any IPv4 Example: To allow...
Installation Guide for SNMPWEBCARD 933179
Page 14
... and Configure 4-1 Test Network Connection: After an IP address has been assigned to the card, try to the SNMPWEBCARD User's Guide, included on a computer connected to connected equipment. For more information about configuration and operation of the managed device, refer to access it with the card. 4-2 Default UPS System Shutdown Settings: During a power...
... and Configure 4-1 Test Network Connection: After an IP address has been assigned to the card, try to the SNMPWEBCARD User's Guide, included on a computer connected to connected equipment. For more information about configuration and operation of the managed device, refer to access it with the card. 4-2 Default UPS System Shutdown Settings: During a power...
Installation Guide for SNMPWEBCARD 933179
Page 17
... Trap action profile setup to address book See SNMPWEBCARD User Guide Event Logging Enabled See SNMPWEBCARD User Guide Data Logging Enabled See SNMPWEBCARD User Guide 17 13-01-199-933179.indb 17 4/23/2013 4:01:51 PM Installation 4-2-2 Other Default Settings Setting IP address Telnet Access SSH Access HTTP Access HTTPS Access SNMPv1 Access SNMPv2...
... Trap action profile setup to address book See SNMPWEBCARD User Guide Event Logging Enabled See SNMPWEBCARD User Guide Data Logging Enabled See SNMPWEBCARD User Guide 17 13-01-199-933179.indb 17 4/23/2013 4:01:51 PM Installation 4-2-2 Other Default Settings Setting IP address Telnet Access SSH Access HTTP Access HTTPS Access SNMPv1 Access SNMPv2...