Operation Manual
Page 8
...cutting height. Raise the mower Figure 9 2. CAUTION If the engine has been running, the muffler will be hot and can severely burn you feel resistance, then pull it sharply (Figure 12). Keep away from the hot muffler. Adjust the cutting height as the rear wheels (Figure 9). Note: ...When you pull the recoil start handle (Figure 12). Lower the mower Note: The cutting height settings are 1 inch (25 mm); 1-3/8 inches (35 mm); 1-3/4 inches (44 mm...
...cutting height. Raise the mower Figure 9 2. CAUTION If the engine has been running, the muffler will be hot and can severely burn you feel resistance, then pull it sharply (Figure 12). Keep away from the hot muffler. Adjust the cutting height as the rear wheels (Figure 9). Note: ...When you pull the recoil start handle (Figure 12). Lower the mower Note: The cutting height settings are 1 inch (25 mm); 1-3/8 inches (35 mm); 1-3/4 inches (44 mm...
Operation Manual
Page 9
... to recycle the grass and leaf clippings back into the lawn. If they do not stop properly, stop using your sides, and the mower will automatically keep pace with your hands on -Demand Lever) before bagging the clippings. If the grass bag is on the mower and the bag-on-demand lever is in serious personal...
... to recycle the grass and leaf clippings back into the lawn. If they do not stop properly, stop using your sides, and the mower will automatically keep pace with your hands on -Demand Lever) before bagging the clippings. If the grass bag is on the mower and the bag-on-demand lever is in serious personal...
Operation Manual
Page 12
...that half of the lawn shows through the cut leaf cover. Cutting Leaves • After cutting the lawn, ensure that the blade could hit. • Avoid striking solid objects with a Toro replacement blade. This ...cm) of the grass blade at a slower pace while mowing. - Cutting Grass • Cut only about a third of leaves on your mowing speed if the mower does not cut below the 2-1/8-inch (54... one or two notches higher than the rear wheels. Raise the cutting height on the lawn, set the front wheels at 2-1/8-inch (54 mm) and the rear wheels at the highest cutting height setting and ...
...that half of the lawn shows through the cut leaf cover. Cutting Leaves • After cutting the lawn, ensure that the blade could hit. • Avoid striking solid objects with a Toro replacement blade. This ...cm) of the grass blade at a slower pace while mowing. - Cutting Grass • Cut only about a third of leaves on your mowing speed if the mower does not cut below the 2-1/8-inch (54... one or two notches higher than the rear wheels. Raise the cutting height on the lawn, set the front wheels at 2-1/8-inch (54 mm) and the rear wheels at the highest cutting height setting and ...
Parts Catalog
Page 2
.... The a represents the reference number of each part within the service assembly. For example, a wheel assembly might be identified by reference number 6, the tire by 6:1, the valve by 6:2, and the wheel by reference number 6, you may also order any part individually. Reference Numbers Indicating Quantity In an ...thread forming PRH: phillips round head PTH: phillips truss head PTO: power-take-off RH: right hand ROPS: roll-over protection system RRB: rear roller brush SFH: slotted fillister head SHH: slotted hex head SHWH: slotted hex washer head SPH: slotted pan head SQH: square head SRH:...
.... The a represents the reference number of each part within the service assembly. For example, a wheel assembly might be identified by reference number 6, the tire by 6:1, the valve by 6:2, and the wheel by reference number 6, you may also order any part individually. Reference Numbers Indicating Quantity In an ...thread forming PRH: phillips round head PTH: phillips truss head PTO: power-take-off RH: right hand ROPS: roll-over protection system RRB: rear roller brush SFH: slotted fillister head SHH: slotted hex head SHWH: slotted hex washer head SPH: slotted pan head SQH: square head SRH:...
Parts Catalog
Page 3
All Rights Reserved Contents Deck, Side Chute and Rear Door Assembly 4 Rear Bag Assembly 5 Engine and Blade Assembly 6 Front Wheel and Height-of-Cut Assembly 7 Transmission and Rear Wheel Drive Assembly 8 Handle Assembly 9 Attachments and Accessories 10 © 2011-The Toro® Company Contact us at www.Toro.com. 8111 Lyndale Avenue South Bloomington, MN 55420 3 Printed in the USA.
All Rights Reserved Contents Deck, Side Chute and Rear Door Assembly 4 Rear Bag Assembly 5 Engine and Blade Assembly 6 Front Wheel and Height-of-Cut Assembly 7 Transmission and Rear Wheel Drive Assembly 8 Handle Assembly 9 Attachments and Accessories 10 © 2011-The Toro® Company Contact us at www.Toro.com. 8111 Lyndale Avenue South Bloomington, MN 55420 3 Printed in the USA.
Parts Catalog
Page 8
Transmission and Rear Wheel Drive Assembly Ref. Description 14 108-7476 3 Screw-Plastite 15 110-7191 2 Washer-Thrust 16 115-4668 2 Gear-Pinion, 12T 17 32151-61 2 Ring-Retaining 18 110-1792 2 Wheel Cover ASM 18:2 614426 1 Washer-Stepped 19 614650 2 Bolt-Shoulder 20 115-4695 2 8 Inch Wheel Gear ASM... 21 115-8406 2 Anchor-Bag 22 105-9437 2 Screw-PPH 23 115-2893 1 Shield-Trailing 24 117-1092 2 Screw-PTH 3371-846A 8 C3 Part Number Qty. Description 1 114-7955-03 1 Plate-Rear, LH (HOC) 2 114-7956-03 1 Plate-Rear, RH (HOC) 3 322-3...
Transmission and Rear Wheel Drive Assembly Ref. Description 14 108-7476 3 Screw-Plastite 15 110-7191 2 Washer-Thrust 16 115-4668 2 Gear-Pinion, 12T 17 32151-61 2 Ring-Retaining 18 110-1792 2 Wheel Cover ASM 18:2 614426 1 Washer-Stepped 19 614650 2 Bolt-Shoulder 20 115-4695 2 8 Inch Wheel Gear ASM... 21 115-8406 2 Anchor-Bag 22 105-9437 2 Screw-PPH 23 115-2893 1 Shield-Trailing 24 117-1092 2 Screw-PTH 3371-846A 8 C3 Part Number Qty. Description 1 114-7955-03 1 Plate-Rear, LH (HOC) 2 114-7956-03 1 Plate-Rear, RH (HOC) 3 322-3...