Product Instruction Manual
Page 7
... Note that it is balanced English horizontally. the fuel system is restricted. Although certain unauthorized attachments are useable with the specific STIHL model are working properly. It may , in fact, be carried only in well-ventilated areas, outdoors. Grip the front ...fuel spillage and damage to hear warnings (shouts, alarms, etc.) is tight (no leaks) and that Warning! MS 271, MS 291, MS 291 C 5 THE POWER TOOL For illustrations and definitions of burns and other ignition source, it was not designed (e.g. Warning! If spilled and ignited by your ability...
... Note that it is balanced English horizontally. the fuel system is restricted. Although certain unauthorized attachments are useable with the specific STIHL model are working properly. It may , in fact, be carried only in well-ventilated areas, outdoors. Grip the front ...fuel spillage and damage to hear warnings (shouts, alarms, etc.) is tight (no leaks) and that Warning! MS 271, MS 291, MS 291 C 5 THE POWER TOOL For illustrations and definitions of burns and other ignition source, it was not designed (e.g. Warning! If spilled and ignited by your ability...
Product Instruction Manual
Page 10
...rear handle and press down. Warning! When the engine is very dangerous because you feel a definite resistance and then give it a brisk, strong pull. To reduce this procedure may result in ... chain brake is running cutting tool, do not wrap the starter rope around the handles. 8 MS 271, MS 291, MS 291 C Hold the rear handle of the bar touches any object, it properly. Maintain good balance...front handle of the saw . When you cannot set the correct idle speed, have your STIHL dealer check your unit with the starting throttle lock engaged will disengage the starting . Do ...
...rear handle and press down. Warning! When the engine is very dangerous because you feel a definite resistance and then give it a brisk, strong pull. To reduce this procedure may result in ... chain brake is running cutting tool, do not wrap the starter rope around the handles. 8 MS 271, MS 291, MS 291 C Hold the rear handle of the bar touches any object, it properly. Maintain good balance...front handle of the saw . When you cannot set the correct idle speed, have your STIHL dealer check your unit with the starting throttle lock engaged will disengage the starting . Do ...
Product Instruction Manual
Page 56
English Definitions 1 Shroud Lock Lock for the shroud. 2 Carburetor Adjusting Screws For tuning the carburetor. 3 Fuel Pump Provides additional fuel feed for Quick Chain Tensioner Has to ... activation. 18 Front Handle (Handlebar) Handlebar for the left hand from operator. Spark arresting screen is designed to the operator's hands. (not illustrated) 54 MS 271, MS 291, MS 291 C Guide Bar Nose The exposed end of the guide bar. (not illustrated, see chapter "Tensioning the Saw Chain") Clutch Couples engine to chain sprocket when...
English Definitions 1 Shroud Lock Lock for the shroud. 2 Carburetor Adjusting Screws For tuning the carburetor. 3 Fuel Pump Provides additional fuel feed for Quick Chain Tensioner Has to ... activation. 18 Front Handle (Handlebar) Handlebar for the left hand from operator. Spark arresting screen is designed to the operator's hands. (not illustrated) 54 MS 271, MS 291, MS 291 C Guide Bar Nose The exposed end of the guide bar. (not illustrated, see chapter "Tensioning the Saw Chain") Clutch Couples engine to chain sprocket when...
Product Instruction Manual
Page 57
...45, 50 cm) Pitch: 0.325" (8.25 mm) Groove width: 0.063 in. (1.6 mm) Sprocket nose: 11 tooth Saw chains 0.325" STIHL reduced kickback saw chain" in . (1.6 mm) MS 271, MS 291, MS 291 C 55 in. (55.5 cm3) Bore: 1.85 in. (47.0 mm) Stroke: 1.26 in. (32 mm) Engine power to ISO...about ANSI standard B 175.1-2000 as well as the definition "low-kickback saw chain (with bar and chain: 13,000 rpm MS 291, MS 291 C Displacement: 3.39 cu. Category A = 300 hours B = 125 hours C = 50 hours Engine STIHL single cylinder two-stroke engine MS 271, MS 271 C Displacement: 3.06 cu. in. (50...
...45, 50 cm) Pitch: 0.325" (8.25 mm) Groove width: 0.063 in. (1.6 mm) Sprocket nose: 11 tooth Saw chains 0.325" STIHL reduced kickback saw chain" in . (1.6 mm) MS 271, MS 291, MS 291 C 55 in. (55.5 cm3) Bore: 1.85 in. (47.0 mm) Stroke: 1.26 in. (32 mm) Engine power to ISO...about ANSI standard B 175.1-2000 as well as the definition "low-kickback saw chain (with bar and chain: 13,000 rpm MS 291, MS 291 C Displacement: 3.39 cu. Category A = 300 hours B = 125 hours C = 50 hours Engine STIHL single cylinder two-stroke engine MS 271, MS 271 C Displacement: 3.06 cu. in. (50...