Product Instruction Manual
Page 40
... different bar lengths, types of wood and cutting techniques. : Use the adjusting screw (1) (on filing gauge* - every time you sharpen the chain and every time you have retensioned it could damage the crankshaft and bearings. MS 290, MS 310, MS 390 * Special accessory * see "Guide to Using this helps avoid one-sided wear, especially at...
... different bar lengths, types of wood and cutting techniques. : Use the adjusting screw (1) (on filing gauge* - every time you sharpen the chain and every time you have retensioned it could damage the crankshaft and bearings. MS 290, MS 310, MS 390 * Special accessory * see "Guide to Using this helps avoid one-sided wear, especially at...
Product Instruction Manual
Page 49
... 30 85 Cutter shapes: Micro = Semi-chisel Super = Full chisel The specified angles A and B are obtained automatically if the recommended files or sharpening tools and correct settings are used. 48 MS 290, MS 310, MS 390 and in the links and damaged rivets. : Replace any damaged or worn parts of each cutter. Do not work...
... 30 85 Cutter shapes: Micro = Semi-chisel Super = Full chisel The specified angles A and B are obtained automatically if the recommended files or sharpening tools and correct settings are used. 48 MS 290, MS 310, MS 390 and in the links and damaged rivets. : Replace any damaged or worn parts of each cutter. Do not work...
Product Instruction Manual
Page 50
... Tools"). It also cleans the guide bar groove and oil inlet holes. 90° File correctly : Select sharpening tools according to the angles marked on the top plate and depth gauge. 689BA043 KN MS 290, MS 310, MS 390 49 For checking angles 85° 70° 90° 60° 80...° : Sharpen chain frequently, take away as little metal as possible - two or three strokes of guide bar) and file according to chain pitch. : Clamp the...
... Tools"). It also cleans the guide bar groove and oil inlet holes. 90° File correctly : Select sharpening tools according to the angles marked on the top plate and depth gauge. 689BA043 KN MS 290, MS 310, MS 390 49 For checking angles 85° 70° 90° 60° 80...° : Sharpen chain frequently, take away as little metal as possible - two or three strokes of guide bar) and file according to chain pitch. : Clamp the...
Product Instruction Manual
Page 51
...break. : Find the shortest cutter and then file all other cutters back to be the same length. All cutters must be lowered. : File down the depth gauge until it is level with the filing gauge. 689BA051 KN 50 MS 290, MS 310, MS 390 lift the file off the cutter on the backstroke. : ...Avoid touching the tie straps and drive links with the filing gauge. English / USA 689BA047 KN : Always file from the inside to check the setting every...
...break. : Find the shortest cutter and then file all other cutters back to be the same length. All cutters must be lowered. : File down the depth gauge until it is level with the filing gauge. 689BA051 KN 50 MS 290, MS 310, MS 390 lift the file off the cutter on the backstroke. : ...Avoid touching the tie straps and drive links with the filing gauge. English / USA 689BA047 KN : Always file from the inside to check the setting every...
Product Instruction Manual
Page 52
... gauge must not be level with the depth gauge. The other parts of tie strap (with service marking) is lowered along with round file, flat file and filing gauge MS 290, MS 310, MS 390 51 English / USA : File the top of -service period, clean the chain and store it in this may increase the kickback tendency of...
... gauge must not be level with the depth gauge. The other parts of tie strap (with service marking) is lowered along with round file, flat file and filing gauge MS 290, MS 310, MS 390 51 English / USA : File the top of -service period, clean the chain and store it in this may increase the kickback tendency of...