Operater's Manual
Page 12
...IF: for tion 7104232 t c Decal, Control Panel, o u L.H. Part No. 7104232 7104233 Decal, Control Panel, R.H. CHECK MOWER BLADE STOPPING TIME The mower blades and mower drive belt should come to start the engine. Do not attempt to bypass or tamper with ground speed levers not locked in order to...Part No. 7104231 If the unit does not pass a safety test, do not operate it. Decal, Weight Limit Part No. 7101940 12 www.Snapper.com ENGINE SHOULD NOT CRANK IF: Decal, Ground Speed Lever, L.H. Operator Safety Safety Interlock System Tests This unit is turned off (or operator rises...
...IF: for tion 7104232 t c Decal, Control Panel, o u L.H. Part No. 7104232 7104233 Decal, Control Panel, R.H. CHECK MOWER BLADE STOPPING TIME The mower blades and mower drive belt should come to start the engine. Do not attempt to bypass or tamper with ground speed levers not locked in order to...Part No. 7104231 If the unit does not pass a safety test, do not operate it. Decal, Weight Limit Part No. 7101940 12 www.Snapper.com ENGINE SHOULD NOT CRANK IF: Decal, Ground Speed Lever, L.H. Operator Safety Safety Interlock System Tests This unit is turned off (or operator rises...
Operater's Manual
Page 24
... (F, Figure 16) in the direction indicated by the arrow, and remove the mower belt from the holes in the cutting height indicator (B) indicates the cutting height of the mower deck, then lower the mower deck to the rear R lift arms (C), and pull the arms out from ...Mower Belt Routing ep 4. Retain all removed hardware. 5. A Figure 15. Cutting Height Adjustment E D for all moving parts to stop. 2. Pivot the front wheels out of the way and slide the mower deck out from under each end of the mower deck. Place a 2 x 4 or similiar support under the unit. 24 www.Snapper...
... (F, Figure 16) in the direction indicated by the arrow, and remove the mower belt from the holes in the cutting height indicator (B) indicates the cutting height of the mower deck, then lower the mower deck to the rear R lift arms (C), and pull the arms out from ...Mower Belt Routing ep 4. Retain all removed hardware. 5. A Figure 15. Cutting Height Adjustment E D for all moving parts to stop. 2. Pivot the front wheels out of the way and slide the mower deck out from under each end of the mower deck. Place a 2 x 4 or similiar support under the unit. 24 www.Snapper...
Operater's Manual
Page 25
...hairpin clip (A). 6. Pull back on the tensioning idler (D, Figure 16) in the direction indicated, and install the belt onto the PTO pulley as shown in the front mower deck bracket (B), and secure each with a washer and hairpin clip (A). Front Deck Lift Components RNeprodRight side shown,...a 2 x 4 or similar support under each end of the way and slide the mower deck under the unit. t fo ctioC A B o u Figure 18. Lower the mower deck to stop. 2. r n Important: Be sure the belt is installed properly onto all moving parts to its lowest position (see C Cutting Height ...
...hairpin clip (A). 6. Pull back on the tensioning idler (D, Figure 16) in the direction indicated, and install the belt onto the PTO pulley as shown in the front mower deck bracket (B), and secure each with a washer and hairpin clip (A). Front Deck Lift Components RNeprodRight side shown,...a 2 x 4 or similar support under each end of the way and slide the mower deck under the unit. t fo ctioC A B o u Figure 18. Lower the mower deck to stop. 2. r n Important: Be sure the belt is installed properly onto all moving parts to its lowest position (see C Cutting Height ...
Operater's Manual
Page 26
...Adjustment WARNING To avoid serious injury, perform adjustments only with engine stopped, key removed and rider on component parts, and is turned off . 26 www.Snapper.com Insert a .016"-.018" (0,40-0,45 mm) feeler gauge (C) r through the opening between the frame and top of time it takes for ...an equal amount of operation. Disengage the PTO and check the amount of mower deck. If the mower drive belt does not stop . 3. With parking brake engaged, PTO disengaged and an operator in p Figure 20. Engage the PTO and wait ...
...Adjustment WARNING To avoid serious injury, perform adjustments only with engine stopped, key removed and rider on component parts, and is turned off . 26 www.Snapper.com Insert a .016"-.018" (0,40-0,45 mm) feeler gauge (C) r through the opening between the frame and top of time it takes for ...an equal amount of operation. Disengage the PTO and check the amount of mower deck. If the mower drive belt does not stop . 3. With parking brake engaged, PTO disengaged and an operator in p Figure 20. Engage the PTO and wait ...
Operater's Manual
Page 29
... and after lubrication. Grease: • front caster wheel axles 2x • front caster spindle bosses • front axle center pivot • mower blade spindles * • mower deck idler arm • mower deck lift motor screw (located up under 2x right fender) Use grease fittings when present. Use automotive-type lithium grease. * Some blade... are not installed. Figure 29. Remember to moving metal parts should be oiled where contact is made with other parts. Keep oil and grease N d off belts and pulleys. Not all moving parts when grease fittings are compatible.
... and after lubrication. Grease: • front caster wheel axles 2x • front caster spindle bosses • front axle center pivot • mower blade spindles * • mower deck idler arm • mower deck lift motor screw (located up under 2x right fender) Use grease fittings when present. Use automotive-type lithium grease. * Some blade... are not installed. Figure 29. Remember to moving metal parts should be oiled where contact is made with other parts. Keep oil and grease N d off belts and pulleys. Not all moving parts when grease fittings are compatible.
Operater's Manual
Page 32
.... LOOK FOR REMEDY Mower deck not properly installed. See Servicing the Mower Blades. Cutting height set too low. See authorized service dealer. Mower drive belt broken. See authorized service...Mower blades are out of balance. Blade installed incorrectly. See authorized service dealer. See Servicing the Mower Blades. See authorized service dealer. Excessive belt wear or breakage. Bent or rough pulleys. Using incorrect belt. See authorized service dealer. Mower drive belt slips or fails to drive. See authorized service dealer. 32 www.Snapper...
.... LOOK FOR REMEDY Mower deck not properly installed. See Servicing the Mower Blades. Cutting height set too low. See authorized service dealer. Mower drive belt broken. See authorized service...Mower blades are out of balance. Blade installed incorrectly. See authorized service dealer. See Servicing the Mower Blades. See authorized service dealer. Excessive belt wear or breakage. Bent or rough pulleys. Using incorrect belt. See authorized service dealer. Mower drive belt slips or fails to drive. See authorized service dealer. 32 www.Snapper...