Barracuda 7200.8 PATA Product Manual
Page 29
...option Computers that use cable select determine the master and slave drives by their BIOS detects a disc drive with non ATAcompatible slave Cable select Limit drive capacity to configure the drive for operation. This limits the drive's capacity to 32 Gbytes when the alternate capacity jumper is...Update the BIOS • Use third-party software such as slave. Master and slave drives are needed to report the full capacity. Barracuda 7200.8 PATA Product Manual, Rev. Master or single drive. It is used . Use this option. 3.3.3 Alternate capacity jumper Some older computers ...
...option Computers that use cable select determine the master and slave drives by their BIOS detects a disc drive with non ATAcompatible slave Cable select Limit drive capacity to configure the drive for operation. This limits the drive's capacity to 32 Gbytes when the alternate capacity jumper is...Update the BIOS • Use third-party software such as slave. Master and slave drives are needed to report the full capacity. Barracuda 7200.8 PATA Product Manual, Rev. Master or single drive. It is used . Use this option. 3.3.3 Alternate capacity jumper Some older computers ...
Barracuda 7200.8 PATA Product Manual
Page 30
... 80-conductor cable by sensing a capacitor at the host side through the CBLID- The drive detects the 80-conductor cable by sampling pin 34, CBLID-, on the interface bus. See Figure 6 for cooling. • Use only 6-32 UNC mounting screws. ...not overtighten the mounting screws (maximum torque: 6 inch-lb.). • Do not use a drive interface cable that is more than 18 inches long. 24 Barracuda 7200.8 PATA Product Manual, Rev. F Follow these important mounting precautions when mounting the drive: • Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter...
... 80-conductor cable by sensing a capacitor at the host side through the CBLID- The drive detects the 80-conductor cable by sampling pin 34, CBLID-, on the interface bus. See Figure 6 for cooling. • Use only 6-32 UNC mounting screws. ...not overtighten the mounting screws (maximum torque: 6 inch-lb.). • Do not use a drive interface cable that is more than 18 inches long. 24 Barracuda 7200.8 PATA Product Manual, Rev. F Follow these important mounting precautions when mounting the drive: • Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter...
Barracuda 7200.8 PATA Product Manual
Page 38
Bit Word 93 13 1 = 80-conductor cable detected, CBLID above VIH 0 = 40-conductor cable detected, CBLID below for words 63, 88, and 93 of the Identify Drive data: Description (if bit is set to 1) Bit Word 63 0 Multiword DMA mode 0 is supported. 1 Multiword DMA mode 1 is supported... is currently active. Word 128 129-159 160-254 255 Description Security status Seagate-reserved ATA-reserved Integrity word Value 0001H xxxxH 0000H xxA5H Note. F See the bit descriptions below VIL 32 Barracuda 7200.8 PATA Product Manual, Rev. Advanced Power Management (APM) and Automatic ...
Bit Word 93 13 1 = 80-conductor cable detected, CBLID above VIH 0 = 40-conductor cable detected, CBLID below for words 63, 88, and 93 of the Identify Drive data: Description (if bit is set to 1) Bit Word 63 0 Multiword DMA mode 0 is supported. 1 Multiword DMA mode 1 is supported... is currently active. Word 128 129-159 160-254 255 Description Security status Seagate-reserved ATA-reserved Integrity word Value 0001H xxxxH 0000H xxA5H Note. F See the bit descriptions below VIL 32 Barracuda 7200.8 PATA Product Manual, Rev. Advanced Power Management (APM) and Automatic ...