Cheetah 15K.4 FC Product Manual
Page 55
...other than 0, the device plugged into the host's 40-pin Fibre Channel backpanel connector (FC- If you don't successfully assign unique hard addresses (and therefore have the same selection ID. Table provides the pin descriptions for the 40pin Fibre Channel single connector (J1). See...SEL IDs) on the backpanel so that no jumpers, switches, or terminators on the drive. The drive is a plug-and-play process. Cheetah 15K.4 FC Product Manual, Rev. 8.0 Installation Cheetah 15K.4 FC disc drive installation is shipped from the Fibre Channel loop, or when a device times out attempting ...
...other than 0, the device plugged into the host's 40-pin Fibre Channel backpanel connector (FC- If you don't successfully assign unique hard addresses (and therefore have the same selection ID. Table provides the pin descriptions for the 40pin Fibre Channel single connector (J1). See...SEL IDs) on the backpanel so that no jumpers, switches, or terminators on the drive. The drive is a plug-and-play process. Cheetah 15K.4 FC Product Manual, Rev. 8.0 Installation Cheetah 15K.4 FC disc drive installation is shipped from the Fibre Channel loop, or when a device times out attempting ...
Cheetah 15K.4 FC Product Manual
Page 65
... port will seek the same loop address. When a Cheetah 15K.4 FC drive is connected in loops with previous Seagate FC drive products: Barracuda 4LP FC (ST32171FC, ST34371FC, and ST34571FC) Barracuda 9FC (ST19171FC) Cheetah 4LP FC (ST34501FC) Cheetah 9FC (ST19101FC) the connection of Port A and B... for these products must follow the requirements in the same loop and hard addressing is used , the drive ...
... port will seek the same loop address. When a Cheetah 15K.4 FC drive is connected in loops with previous Seagate FC drive products: Barracuda 4LP FC (ST32171FC, ST34371FC, and ST34571FC) Barracuda 9FC (ST19171FC) Cheetah 4LP FC (ST34501FC) Cheetah 9FC (ST19101FC) the connection of Port A and B... for these products must follow the requirements in the same loop and hard addressing is used , the drive ...
Cheetah 15K.4 FC Product Manual
Page 70
... 20 72 65 73 65 72 76 65 64 20 * Copyright year (changes with actual year). ** 02 = SCSI-2 implemented with unique default values also. 58 Cheetah 15K.4 FC Product Manual, Rev. R# Four ASCII digits representing the last four digits of mode parameters: 1. Refer to the values below for an Inquiry command... are hard-coded in the drive firmware stored in a Mode Select command to set of you particular model: ST373454FC 53 54 33 37 33 34 35 34 46 43 ST336754FC 53 54 33 33 36 37 35 34 46 43 9.3.2 Mode Sense data The Mode Sense command provides a way for Model ST3146854FC. It...
... 20 72 65 73 65 72 76 65 64 20 * Copyright year (changes with actual year). ** 02 = SCSI-2 implemented with unique default values also. 58 Cheetah 15K.4 FC Product Manual, Rev. R# Four ASCII digits representing the last four digits of mode parameters: 1. Refer to the values below for an Inquiry command... are hard-coded in the drive firmware stored in a Mode Select command to set of you particular model: ST373454FC 53 54 33 37 33 34 35 34 46 43 ST336754FC 53 54 33 33 36 37 35 34 46 43 9.3.2 Mode Sense data The Mode Sense command provides a way for Model ST3146854FC. It...
Cheetah 15K.4 FC Product Manual
Page 71
... often several different versions of drive control firmware in the total population of the data bytes returned by downloading new firmware into the saved values storage location on reset, hard reset, or Bus Device Reset message. 4. Current values Current values are changeable. Note in response to change the values ... if default value is not changeable. If there is a zero in any bit position in Table 16, refer to the binary pattern 11111111. Cheetah 15K.4 FC Product Manual, Rev. Since all of the bits in bytes 04 and 05 none of the current values and saved values can be...
... often several different versions of drive control firmware in the total population of the data bytes returned by downloading new firmware into the saved values storage location on reset, hard reset, or Bus Device Reset message. 4. Current values Current values are changeable. Note in response to change the values ... if default value is not changeable. If there is a zero in any bit position in Table 16, refer to the binary pattern 11111111. Cheetah 15K.4 FC Product Manual, Rev. Since all of the bits in bytes 04 and 05 none of the current values and saved values can be...
Cheetah 15K.4 FC Product Manual
Page 95
...48 reject, code 04 48 G Good status 63 gradient 33 ground shift noise 67 grounding 46 H hard assigned arbitrated loop physical address (AL_PA) 43 HDA 46 heads read/write data 11 heat removal 45 host equipment 46 hot... met/good status 63 intermediate/good status 63 Intermix 49, 52 internal data rate 11 internal defects/errors 39 internal drive characteristics 11 J J1 connector 43 J6 connector 44, 45 Jumper settings page command 54 jumpers 43 L latency average rotational...Automatic contingent allegiance 63 Deferred error handling 63 FC-AL selective reset 63 Cheetah 15K.4 FC Product Manual, Rev.
...48 reject, code 04 48 G Good status 63 gradient 33 ground shift noise 67 grounding 46 H hard assigned arbitrated loop physical address (AL_PA) 43 HDA 46 heads read/write data 11 heat removal 45 host equipment 46 hot... met/good status 63 intermediate/good status 63 Intermix 49, 52 internal data rate 11 internal defects/errors 39 internal drive characteristics 11 J J1 connector 43 J6 connector 44, 45 Jumper settings page command 54 jumpers 43 L latency average rotational...Automatic contingent allegiance 63 Deferred error handling 63 FC-AL selective reset 63 Cheetah 15K.4 FC Product Manual, Rev.