User Manual
Page 7
... for location and function of other people and objects. TO ROLL TRACTOR OFF SKID (See Operation section for replacing motion and mower blade drive belts in front of tractor is properly leveled side-to-side/ front-to its adjusted position. • Raise seat and tighten adjustment knob ... how to operate your tractor were overinflated at proper level. ✓ Fuel tank is important for leveling). ✓ Check mower and drive belts. Be sure tractor is operating properly. Be sure they are routed properly around pulleys and inside all connections are still secure and wires ...
... for location and function of other people and objects. TO ROLL TRACTOR OFF SKID (See Operation section for replacing motion and mower blade drive belts in front of tractor is properly leveled side-to-side/ front-to its adjusted position. • Raise seat and tighten adjustment knob ... how to operate your tractor were overinflated at proper level. ✓ Fuel tank is important for leveling). ✓ Check mower and drive belts. Be sure tractor is operating properly. Be sure they are routed properly around pulleys and inside all connections are still secure and wires ...
User Manual
Page 17
...'s air cooling system. CLAMP CLAMP CLEANING • Clean engine, battery, seat, finish, etc. Debris can restrict clutch/brake pedal shaft movement, causing belt slip and loss of use, whichever comes first. CAUTION: Avoid all pinch points and movable parts (See Fig. 17) CLUTCH/BRAKE PEDAL CLEAN TOP ... washer to keep water out. MAINTENANCE CLEAN AIR SCREEN Air screen must be replaced once each mowing season or after every 100 hours of drive. Clean with a wire brush or compressed air to prevent overheating and engine damage. AIR FILTER Your engine will shorten the useful life of...
...'s air cooling system. CLAMP CLAMP CLEANING • Clean engine, battery, seat, finish, etc. Debris can restrict clutch/brake pedal shaft movement, causing belt slip and loss of use, whichever comes first. CAUTION: Avoid all pinch points and movable parts (See Fig. 17) CLUTCH/BRAKE PEDAL CLEAN TOP ... washer to keep water out. MAINTENANCE CLEAN AIR SCREEN Air screen must be replaced once each mowing season or after every 100 hours of drive. Clean with a wire brush or compressed air to prevent overheating and engine damage. AIR FILTER Your engine will shorten the useful life of...
User Manual
Page 21
...when you try to stop at highest speed in this section of manual). BELT REMOVAL • Remove mower (See "TO REMOVE MOWER" in neutral (N) position. NOTE: Observe entire motion drive belt and position of all belt guides and keepers. • Install mower (See "TO INSTALL MOWER" ...G 02954 Manual Fig. 29 21 SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 28) The mower blade drive belt may also check brake by: • Park tractor on a level, dry concrete or paved surface, depress brake pedal all belt guides. • Install mower (See "To Install Mower" in highest ...
...when you try to stop at highest speed in this section of manual). BELT REMOVAL • Remove mower (See "TO REMOVE MOWER" in neutral (N) position. NOTE: Observe entire motion drive belt and position of all belt guides and keepers. • Install mower (See "TO INSTALL MOWER" ...G 02954 Manual Fig. 29 21 SERVICE AND ADJUSTMENTS TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 28) The mower blade drive belt may also check brake by: • Park tractor on a level, dry concrete or paved surface, depress brake pedal all belt guides. • Install mower (See "To Install Mower" in highest ...
User Manual
Page 26
...Bent blade mandrel. 5. Remove obstruction. 2. Place throttle control in parts manual. 11. Wet grass. 3. Level mower deck. 5. Replace mower drive belt. 9. Reinstall blades sharp edge down. 10. Replace with attachment clutch engaged 1. of grass, leaves, and trash around mandrels. 1. Turn ...switch "ON". 2. Replace fuse. Bad battery cell(s). 2. Replace battery. 2. Replace regulator. 4. Motion drive belt worn, damaged, or broken. 3. Install axle key at rear wheel. See "TO REMOVE WHEEL" in the maintenance section. 2. If ...
...Bent blade mandrel. 5. Remove obstruction. 2. Place throttle control in parts manual. 11. Wet grass. 3. Level mower deck. 5. Replace mower drive belt. 9. Reinstall blades sharp edge down. 10. Replace with attachment clutch engaged 1. of grass, leaves, and trash around mandrels. 1. Turn ...switch "ON". 2. Replace fuse. Bad battery cell(s). 2. Replace battery. 2. Replace regulator. 4. Motion drive belt worn, damaged, or broken. 3. Install axle key at rear wheel. See "TO REMOVE WHEEL" in the maintenance section. 2. If ...
Parts Manual
Page 9
...13/16 x 16 Ga. Cover, Foot Pedal Bolt Pulley Idler Flat Lock Nut 3/8-16 Idler V-Groove V-Belt, Drive Pulley Transaxle Shaft Asm. NO. 160 532 16 94-84 161 532 10 57-09 165 532 19 ...Spacer Axle Handle Parking Brake Bolt 3/8-16 unc x 2-3/4 Gr. 5 Spacer Retainer Washer Link Clutch Ground Drive Bellcrank Ground Drive Keeper Bellcrank Ground Drive Nut Lock Center 1/4-28 Fnthd Screw 5/16-18 x 3/4 Bracket Brake Rod Link Transaxle Washer 11/... Bolt 1/4-28 unf Gr. 8 w/Patch Washer Lock Hvy Helical 1/4 Washer 9/32 x 3/4 x 10 Ga. PXT195G42 (96046002200), PRODUCT NO. 960 46 00-22 DRIVE KEY PART NO.
...13/16 x 16 Ga. Cover, Foot Pedal Bolt Pulley Idler Flat Lock Nut 3/8-16 Idler V-Groove V-Belt, Drive Pulley Transaxle Shaft Asm. NO. 160 532 16 94-84 161 532 10 57-09 165 532 19 ...Spacer Axle Handle Parking Brake Bolt 3/8-16 unc x 2-3/4 Gr. 5 Spacer Retainer Washer Link Clutch Ground Drive Bellcrank Ground Drive Keeper Bellcrank Ground Drive Nut Lock Center 1/4-28 Fnthd Screw 5/16-18 x 3/4 Bracket Brake Rod Link Transaxle Washer 11/... Bolt 1/4-28 unf Gr. 8 w/Patch Washer Lock Hvy Helical 1/4 Washer 9/32 x 3/4 x 10 Ga. PXT195G42 (96046002200), PRODUCT NO. 960 46 00-22 DRIVE KEY PART NO.