EY6932 User Guide
Page 3
...of children and other untrained persons. SPECIFIC SAFETY RULES 1) Hold tool by holding the speed control trigger halfway (speed control mode) so that the motor stops. - 3 - Service 21) Tool service must be plugged into an electrical outlet. 4) Do not operate the Forward/ Reverse lever when ... condition, it on . Prolonged exposure to high intensity noise can cause hearing loss. 3) Be aware that can damage the battery pack or motor. Use the correct tool for extended periods. Tools are caused by unqualified personnel may occur. 5) If the bit becomes jammed, immediately turn...
...of children and other untrained persons. SPECIFIC SAFETY RULES 1) Hold tool by holding the speed control trigger halfway (speed control mode) so that the motor stops. - 3 - Service 21) Tool service must be plugged into an electrical outlet. 4) Do not operate the Forward/ Reverse lever when ... condition, it on . Prolonged exposure to high intensity noise can cause hearing loss. 3) Be aware that can damage the battery pack or motor. Use the correct tool for extended periods. Tools are caused by unqualified personnel may occur. 5) If the bit becomes jammed, immediately turn...
EY6932 User Guide
Page 7
....) For driving screws 5 Approx. 4.4 Nm into place to mortar, brick, etc. - 7 - A feedback electronic controller is released and the motor stops immediately. For reverse rotation, set the lever to start the tool slowly. 3. Depress the trigger switch slightly to its center position (switch lock... pack. After use , set the lever to give a strong torque even in -lbs.) For powerful driving and drilling Percussion For drilling to indicate proper connection. 2. OPERATION Switch Operation 1. The speed increases with the amount of depression of screws and Reference...
....) For driving screws 5 Approx. 4.4 Nm into place to mortar, brick, etc. - 7 - A feedback electronic controller is released and the motor stops immediately. For reverse rotation, set the lever to start the tool slowly. 3. Depress the trigger switch slightly to its center position (switch lock... pack. After use , set the lever to give a strong torque even in -lbs.) For powerful driving and drilling Percussion For drilling to indicate proper connection. 2. OPERATION Switch Operation 1. The speed increases with the amount of depression of screws and Reference...
EY6932 User Guide
Page 8
... firmly into the AC outlet. Speed Selection Choose a low or high speed to full capacity. The more torque than the maximum torque of the driver (position on the speed control trigger. Use at high speed while a strong force is used as a manual screwdriver (up to suit the use...between 0°C (32°F) and 40°C (104°F). The ambient temperature range is below 0°C (32°F) the tool may cause a motor breakdown.) Do not operate the speed selector switch (LOW-HIGH) while pulling on the clutch), for appropriate functioning of the battery. With the trigger switch...
... firmly into the AC outlet. Speed Selection Choose a low or high speed to full capacity. The more torque than the maximum torque of the driver (position on the speed control trigger. Use at high speed while a strong force is used as a manual screwdriver (up to suit the use...between 0°C (32°F) and 40°C (104°F). The ambient temperature range is below 0°C (32°F) the tool may cause a motor breakdown.) Do not operate the speed selector switch (LOW-HIGH) while pulling on the clutch), for appropriate functioning of the battery. With the trigger switch...
EY6932 User Guide
Page 10
... SPEED WHEN STRONG FORCE IS NEEDED DURING OPERATION. (Using at high speed while a strong force is recyclable powers the product you have purchased. EY6932 DRILLING SCREW TIGHTENING MATERIAL/ MORTAR / CONDITION BRICK WOOD / YELLOW PINE Thickness: 40 mm (1-37/64") or less METAL METAL HOLE SAW Cold-rolled... on how to select low or high speed for cleaning. BATTERY RECYCLING ATTENTION: A nickel metal hydride battery that is applied may cause a motor breakdown.) Use the following as a guide to recycle this battery. . Do not use a damp cloth, thinner, benzine, or other volatile solvents ...
... SPEED WHEN STRONG FORCE IS NEEDED DURING OPERATION. (Using at high speed while a strong force is recyclable powers the product you have purchased. EY6932 DRILLING SCREW TIGHTENING MATERIAL/ MORTAR / CONDITION BRICK WOOD / YELLOW PINE Thickness: 40 mm (1-37/64") or less METAL METAL HOLE SAW Cold-rolled... on how to select low or high speed for cleaning. BATTERY RECYCLING ATTENTION: A nickel metal hydride battery that is applied may cause a motor breakdown.) Use the following as a guide to recycle this battery. . Do not use a damp cloth, thinner, benzine, or other volatile solvents ...
EY6932 User Guide
Page 11
...- EY9230 EY9200 - - SPECIFICATIONS MAIN UNIT Model Screw driving Machine screw Wood screw Masonry screw Capability Mortar/Brick Drilling Wood Metal Metal hole saw Motor No load speed LOW HIGH Blows rate per LOW minute HIGH Chuck capacity Blow strength Overall length Weight (with battery... pack) EY6932 M3 ~ M6 ø 2.1 ~ ø 6.8 mm (5/64" ~ 17/64") ø 4 ~ ø 6 mm (5/32" ~ 15/64") ø 3 ~ ø 13 mm (1/8" ~ 1/2") ø 3 ~ ø 36 mm (1/8" ~ 1-27/64") ø 1.5 ~ ø 13 mm (1/16" ~ 1/2") Max. ø 34 mm (1-11/32") DC Motor 15.6 V 80 ~...
...- EY9230 EY9200 - - SPECIFICATIONS MAIN UNIT Model Screw driving Machine screw Wood screw Masonry screw Capability Mortar/Brick Drilling Wood Metal Metal hole saw Motor No load speed LOW HIGH Blows rate per LOW minute HIGH Chuck capacity Blow strength Overall length Weight (with battery... pack) EY6932 M3 ~ M6 ø 2.1 ~ ø 6.8 mm (5/64" ~ 17/64") ø 4 ~ ø 6 mm (5/32" ~ 15/64") ø 3 ~ ø 13 mm (1/8" ~ 1/2") ø 3 ~ ø 36 mm (1/8" ~ 1-27/64") ø 1.5 ~ ø 13 mm (1/16" ~ 1/2") Max. ø 34 mm (1-11/32") DC Motor 15.6 V 80 ~...