Owners Guide
Page 1
Includes: • Safety Warnings • Warranty • Operating Instructions • Trouble Diagnosis • Accessories 75726-01 REV A S I M P LY A M A Z I N G® VISIT ONE OF OUR OVER 450 STORE LOCATIONS USA: 1-800-989-4244 CANADA: 1-800-393-8801 USER'S GUIDE U2510RH USA: 1-800-989-3535 CANADA: 1-888-676-7325 COMMERCIAL: 1-800-242-1378 www.oreck.com www.oreckcommercial.com U2520RH VISIT ONE OF OUR OVER 450 STORE LOCATIONS U2530RH HIGH SPEED UPRIGHT VACUUM CLEANER WITH ® CLEANING SYSTEM •IMPORTANT• SAVE THIS BOOKLET!
Includes: • Safety Warnings • Warranty • Operating Instructions • Trouble Diagnosis • Accessories 75726-01 REV A S I M P LY A M A Z I N G® VISIT ONE OF OUR OVER 450 STORE LOCATIONS USA: 1-800-989-4244 CANADA: 1-800-393-8801 USER'S GUIDE U2510RH USA: 1-800-989-3535 CANADA: 1-888-676-7325 COMMERCIAL: 1-800-242-1378 www.oreck.com www.oreckcommercial.com U2520RH VISIT ONE OF OUR OVER 450 STORE LOCATIONS U2530RH HIGH SPEED UPRIGHT VACUUM CLEANER WITH ® CLEANING SYSTEM •IMPORTANT• SAVE THIS BOOKLET!
Owners Guide
Page 2
... fail to fit, contact an electrician to Replace a Worn Belt, To Adjust or Replace Brush, Using an Oreck Fresh Air® Tab, Stuffing or Blockage page 6 Maintenance and Customer Service Your Oreck vacuum cleaner is a product of body away from outlet when not in use with wet hands. • Do ..., some mothproofing substances, or in . Keep cord away from heated surfaces. • Do not run while in this appliance. • Use caution when vacuuming over cord. • Do not unplug by cord, use with this manual. Do not use cord as a toy. with any object into the power outlet...
... fail to fit, contact an electrician to Replace a Worn Belt, To Adjust or Replace Brush, Using an Oreck Fresh Air® Tab, Stuffing or Blockage page 6 Maintenance and Customer Service Your Oreck vacuum cleaner is a product of body away from outlet when not in use with wet hands. • Do ..., some mothproofing substances, or in . Keep cord away from heated surfaces. • Do not run while in this appliance. • Use caution when vacuuming over cord. • Do not unplug by cord, use with this manual. Do not use cord as a toy. with any object into the power outlet...
Owners Guide
Page 5
... hook on handle and cord hook on plug. Operating Recommendations This new ORECK XL High-Speed Upright is one stationary position for vacuum use ONLY ORECK genuine belts. Damage caused by use your vacuum cleaner on damp or wet surfaces. Change the disposable filter dust bag at...DO NOT run while in any one of the revolving brush and is fully rested in its housing. 5. Use caution when vacuuming over matching section of your ORECK vacuum cleaner. Your ORECK disposable dust bags have been numbered as follows: 1 Handle section, upper 2 Tube, lower 3 Power head 4 Outer bag...
... hook on handle and cord hook on plug. Operating Recommendations This new ORECK XL High-Speed Upright is one stationary position for vacuum use ONLY ORECK genuine belts. Damage caused by use your vacuum cleaner on damp or wet surfaces. Change the disposable filter dust bag at...DO NOT run while in any one of the revolving brush and is fully rested in its housing. 5. Use caution when vacuuming over matching section of your ORECK vacuum cleaner. Your ORECK disposable dust bags have been numbered as follows: 1 Handle section, upper 2 Tube, lower 3 Power head 4 Outer bag...
Owners Guide
Page 6
... dust bag connects to show "OLD" and replace in the holding channels in the "NEW" position. Using An Oreck Fresh Air® Tab fig. 20 Your ORECK XL vacuum cleaner has a special ORECK FRESH AIR® tab pocket. Pull tube out of the bag dock. fig. 26 If tube is seated....remove baseplate (fig. 22). Unhook retainer spring, releasing bottom of brush roll to the connector assembly. Remove debris with both bearings must be ordered. Vacuum will hinge downward. Then reinsert tube and push down screw located on the base of the assembly. NOTE: If the above , both bearing assembly...
... dust bag connects to show "OLD" and replace in the holding channels in the "NEW" position. Using An Oreck Fresh Air® Tab fig. 20 Your ORECK XL vacuum cleaner has a special ORECK FRESH AIR® tab pocket. Pull tube out of the bag dock. fig. 26 If tube is seated....remove baseplate (fig. 22). Unhook retainer spring, releasing bottom of brush roll to the connector assembly. Remove debris with both bearings must be ordered. Vacuum will hinge downward. Then reinsert tube and push down screw located on the base of the assembly. NOTE: If the above , both bearing assembly...