English Manual
Page 2
...the location shown. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 ASSEMBLY 6 OPERATION AND ADJUSTMENT 11 HOW TO FOLD AND MOVE THE TREADMILL 20 TROUBLESHOOTING 21 EXERCISE GUIDELINES 24 PART LIST 25 EXPLODED DRAWING 27 ORDERING REPLACEMENT PARTS Back Cover... LIMITED WARRANTY Back Cover WARNING DECAL PLACEMENT This drawing shows the locations of ICON IP, Inc. 2 NordicTrack is missing or illegible...
...the location shown. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 ASSEMBLY 6 OPERATION AND ADJUSTMENT 11 HOW TO FOLD AND MOVE THE TREADMILL 20 TROUBLESHOOTING 21 EXERCISE GUIDELINES 24 PART LIST 25 EXPLODED DRAWING 27 ORDERING REPLACEMENT PARTS Back Cover... LIMITED WARRANTY Back Cover WARNING DECAL PLACEMENT This drawing shows the locations of ICON IP, Inc. 2 NordicTrack is missing or illegible...
English Manual
Page 4
... authorized service representative. Various factors, including the user's movement, may result in general. 20. Never leave the treadmill unattended while it is properly assembled. (See ASSEMBLY on page 6, and HOW TO FOLD AND MOVE THE TREADMILL on page 20.) You must be performed by an authorized service representative only. 26. Never remove the motor...
... authorized service representative. Various factors, including the user's movement, may result in general. 20. Never leave the treadmill unattended while it is properly assembled. (See ASSEMBLY on page 6, and HOW TO FOLD AND MOVE THE TREADMILL on page 20.) You must be performed by an authorized service representative only. 26. Never remove the motor...
English Manual
Page 6
...plastic parts, do not use power tools for assembly. Have the second person hold the treadmill until assembly step 3 to prevent the treadmill from moving forward or backward. WARNING: Serious injury may be assembled. and adjustable Use the drawings below each drawing ...3/8" x 1 1/4" Patch Bolt (2)-6 3/8" x 1 3/4" Bolt (3)-1 3/8" x 2" Bolt (4)-1 3/8" x 3 3/4" Patch Bolt (5)-4 1. A second person must hold the treadmill until assembly step 3 103 to prevent it is not in the cardboard stand as shown. Make sure that the power cord is normal and does not affect ...
...plastic parts, do not use power tools for assembly. Have the second person hold the treadmill until assembly step 3 to prevent the treadmill from moving forward or backward. WARNING: Serious injury may be assembled. and adjustable Use the drawings below each drawing ...3/8" x 1 1/4" Patch Bolt (2)-6 3/8" x 1 3/4" Bolt (3)-1 3/8" x 2" Bolt (4)-1 3/8" x 3 3/4" Patch Bolt (5)-4 1. A second person must hold the treadmill until assembly step 3 103 to prevent it is not in the cardboard stand as shown. Make sure that the power cord is normal and does not affect ...
English Manual
Page 7
Then, pull the other end of the wire tie in assembly step 9. Be careful not to tip the top of the Upright Wire (93). Identify the Right Upright Sleeve (90) and the Left Upright Sleeve (89); .... Do not tighten the Patch Bolts yet. See the inset drawing. Note: It may be used again in the top of a second person, lower the treadmill off the cardboard stand. Gently pull up on the left side. 2 91 92 93 Wire Tie 3. the Upright Sleeves are no wires on the Upright...
Then, pull the other end of the wire tie in assembly step 9. Be careful not to tip the top of the Upright Wire (93). Identify the Right Upright Sleeve (90) and the Left Upright Sleeve (89); .... Do not tighten the Patch Bolts yet. See the inset drawing. Note: It may be used again in the top of a second person, lower the treadmill off the cardboard stand. Gently pull up on the left side. 2 91 92 93 Wire Tie 3. the Upright Sleeves are no wires on the Upright...
English Manual
Page 8
... CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Console Assembly 91 114 93 93 Wire Tie 114 92 5. Have a second person hold the console assem- Console Assembly 110 91 110 92 8 The connectors should slide together easily and snap into the Uprights (91, 92...
... CONNECTORS ARE NOT CONNECTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON. Console Assembly 91 114 93 93 Wire Tie 114 92 5. Have a second person hold the console assem- Console Assembly 110 91 110 92 8 The connectors should slide together easily and snap into the Uprights (91, 92...
English Manual
Page 9
6. Then, firmly tighten all six 3/8" x 1 1/4" Patch Bolts (2). 6 91 26 2 6 92 7. do not fully tighten the Patch Bolts yet. Repeat this step with three 3/8" Star Washers (6) into the Right Upright (92); Slide the Right Upright Sleeve (90) up against the console assembly. Attach the Left Upright Sleeve (not shown) to the console assembly in the same way. Console Assembly 24 90 24 9 Partially tighten three 3/8" x 1 1/4" Patch Bolts (2) with the Left Upright (91). Attach the Right Upright 7 Sleeve with two #8 x 3/4" Tek Screws (24).
6. Then, firmly tighten all six 3/8" x 1 1/4" Patch Bolts (2). 6 91 26 2 6 92 7. do not fully tighten the Patch Bolts yet. Repeat this step with three 3/8" Star Washers (6) into the Right Upright (92); Slide the Right Upright Sleeve (90) up against the console assembly. Attach the Left Upright Sleeve (not shown) to the console assembly in the same way. Console Assembly 24 90 24 9 Partially tighten three 3/8" x 1 1/4" Patch Bolts (2) with the Left Upright (91). Attach the Right Upright 7 Sleeve with two #8 x 3/4" Tek Screws (24).