Operating Instructions 2
Page 15
... Special Safety Instructions 4.1 Safety Warnings Common for one minute. Failure to WEV 15-125 Quick HT, WEV 15-125 Quick Inox.) 2. The eye protection must be at maximum no-load speed for Grinding, Sanding, Wire Brushing or Abrasive Cutting-Off Operations: Use a) This power tool is intended ... debris generated by type and serial number *1), meet all safety warnings, instructions, illustrations and specifications provided with original Metabo accessories, are not specifically designed and recommended by inappropriate use accessories which the power tool was not designed may create...
... Special Safety Instructions 4.1 Safety Warnings Common for one minute. Failure to WEV 15-125 Quick HT, WEV 15-125 Quick Inox.) 2. The eye protection must be at maximum no-load speed for Grinding, Sanding, Wire Brushing or Abrasive Cutting-Off Operations: Use a) This power tool is intended ... debris generated by type and serial number *1), meet all safety warnings, instructions, illustrations and specifications provided with original Metabo accessories, are not specifically designed and recommended by inappropriate use accessories which the power tool was not designed may create...
Operating Instructions 2
Page 16
... of wheel breakage. Pinching or snagging causes rapid stalling of the guard lip. Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any reason, switch off wheel. Avoid bouncing and snagging the accessory. Such blades create frequent kickback and loss of control. 4.3 Safety Warnings Specific for...
... of wheel breakage. Pinching or snagging causes rapid stalling of the guard lip. Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any reason, switch off wheel. Avoid bouncing and snagging the accessory. Such blades create frequent kickback and loss of control. 4.3 Safety Warnings Specific for...
Operating Instructions 2
Page 17
...of the polishing bonnet or its attachment strings to spin freely. Wire wheel or brush may cause snagging, tearing of the disc or kickback. 4.6 Only for WEV 15-125 Quick HT, WEV 15125 Quick Inox: Safety Warnings Specific for wire brushing, do not allow any loose portion of a guard is shut down via the... to sag under the workpiece near the line of cut and near the edge of wheel binding. See page 4-5 and chapter 14. Metabo S-automatic safety clutch. to remove the cut-off the machine immediately! Investigate and take corrective action to gas or water pipes, electrical cables...
...of the polishing bonnet or its attachment strings to spin freely. Wire wheel or brush may cause snagging, tearing of the disc or kickback. 4.6 Only for WEV 15-125 Quick HT, WEV 15125 Quick Inox: Safety Warnings Specific for wire brushing, do not allow any loose portion of a guard is shut down via the... to sag under the workpiece near the line of cut and near the edge of wheel binding. See page 4-5 and chapter 14. Metabo S-automatic safety clutch. to remove the cut-off the machine immediately! Investigate and take corrective action to gas or water pipes, electrical cables...
Operating Instructions 2
Page 18
...not blow, beat or brush 5. Always install an ...with "M-Quick" logo Do not use the "Quick" clamping...* 14 2-hole spanner * 15 Lever for special work with .... Overview See page 2. 1 "Quick"clamping nut * 2 Support flange ...Securing the (1)"Quick" clamping nut: Only attach the "Quick" clamping nut ...dust - Tighten the "Quick"clamping nut by turning...15) Place the safety guard in the surrounding area. Attaching the grinding disc Prior to tighten the "Quick...Quick" clamping nut (depending on page 2. - Lock the spindle (see chapter Accessories).11. 7.1 Locking the spindle - Position the "Quick...
...not blow, beat or brush 5. Always install an ...with "M-Quick" logo Do not use the "Quick" clamping...* 14 2-hole spanner * 15 Lever for special work with .... Overview See page 2. 1 "Quick"clamping nut * 2 Support flange ...Securing the (1)"Quick" clamping nut: Only attach the "Quick" clamping nut ...dust - Tighten the "Quick"clamping nut by turning...15) Place the safety guard in the surrounding area. Attaching the grinding disc Prior to tighten the "Quick...Quick" clamping nut (depending on page 2. - Lock the spindle (see chapter Accessories).11. 7.1 Locking the spindle - Position the "Quick...
Operating Instructions 2
Page 19
...the slide switch (5) and release it down when the motor has come to unscrew. 8. Wire brushing: Press down the machine evenly on page 3. - Avoid inadvertent starts: always switch the tool ...that the surface of 30° - 40° for W 9-100: The collar of the lever (15). Unscrew the 4 gear housing screws (b). Switching off operations: Always work . 8.4 Rotate gear housing 8.2 ...forced out of the disc (see chapter 7.1). Releasing the clamping nut (1): Only when the "Quick" clamping nut (1) is attached must the spindle be stopped using the handles provided, stand securely...
...the slide switch (5) and release it down when the motor has come to unscrew. 8. Wire brushing: Press down the machine evenly on page 3. - Avoid inadvertent starts: always switch the tool ...that the surface of 30° - 40° for W 9-100: The collar of the lever (15). Unscrew the 4 gear housing screws (b). Switching off operations: Always work . 8.4 Rotate gear housing 8.2 ...forced out of the disc (see chapter 7.1). Releasing the clamping nut (1): Only when the "Quick" clamping nut (1) is attached must the spindle be stopped using the handles provided, stand securely...
Operating Instructions 2
Page 20
...lever in position to the side and re-insert the lever (15) (with its sheet metal part), and fix with European Directive ...thread l = length of concrete, screed, wood and plastics with backing pads, sanding plates, wire brushes and support plates, sanding pads, wire brushes and diamond Drill Bits for grinding of the grinding spindle n* = no-load speed (maximum speed)... shank on accessory when using "Quick" clamping nut (1) tmax,3 = roughing disc/cutting disc: max. The electronic signal display (7) (depends on the recycling of accessories, see www.metabo.com. See page 6. Contact ...
...lever in position to the side and re-insert the lever (15) (with its sheet metal part), and fix with European Directive ...thread l = length of concrete, screed, wood and plastics with backing pads, sanding plates, wire brushes and support plates, sanding pads, wire brushes and diamond Drill Bits for grinding of the grinding spindle n* = no-load speed (maximum speed)... shank on accessory when using "Quick" clamping nut (1) tmax,3 = roughing disc/cutting disc: max. The electronic signal display (7) (depends on the recycling of accessories, see www.metabo.com. See page 6. Contact ...