Installation Instructions
Page 3
...to the standards listed above the surface units should be secured to comply with ranges. Additional Installation Requirements The installation of 194° (90°C). The appliance... mm) drill bit (for wood floors) 4.8 mm) carbide-tipped masonry drill bit (for concrete/ceramic floors) ■ Tin snips or large wire cutters (for Manufactured Home Installations, ANSI A225.1/NFPA ...501A or local codes. See "Electrical Requirements" section. The model/serial rating plate is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening ...
...to the standards listed above the surface units should be secured to comply with ranges. Additional Installation Requirements The installation of 194° (90°C). The appliance... mm) drill bit (for wood floors) 4.8 mm) carbide-tipped masonry drill bit (for concrete/ceramic floors) ■ Tin snips or large wire cutters (for Manufactured Home Installations, ANSI A225.1/NFPA ...501A or local codes. See "Electrical Requirements" section. The model/serial rating plate is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening ...
Installation Instructions
Page 4
... wire is used, it will not fit the outlet, have a proper outlet installed by not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. 30" (76.2 cm) minimum clearance between cutout and cabinet door or hinge. *NOTE... ¹⁄₄" (0.64 cm) flame retardant millboard covered with leveling legs screwed all local codes and ordinances. Model/serial rating plate (located on the left side frame behind storage drawer panel) *Range can result in * D. 29⁷⁄₈" (75.9 cm) width E. 25" (63.5 cm) depth F. A. ...
... wire is used, it will not fit the outlet, have a proper outlet installed by not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper. 30" (76.2 cm) minimum clearance between cutout and cabinet door or hinge. *NOTE... ¹⁄₄" (0.64 cm) flame retardant millboard covered with leveling legs screwed all local codes and ordinances. Model/serial rating plate (located on the left side frame behind storage drawer panel) *Range can result in * D. 29⁷⁄₈" (75.9 cm) width E. 25" (63.5 cm) depth F. A. ...
Installation Instructions
Page 5
...4-wire power supply cord is connected to the cabinet. Refer to the figures in a NEMA Type 14-50P plug on the model/serial rating plate. **If connecting to the cabinet. Range Rating* 120/240 Volts 8.8 - 16.5 KW 16.6 - 22.5 KW 120/208 Volts 7.8 - 12.5 KW 12.6 - 18.5 KW Specified... electrical voltage and frequency as specified on the oven frame behind the control panel or on the model/serial number rating plate. or 50-amp power supply cord (pigtail) (see following Range Rating chart). See the "Electrical Connection" section. ■ Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack ...
...4-wire power supply cord is connected to the cabinet. Refer to the figures in a NEMA Type 14-50P plug on the model/serial rating plate. **If connecting to the cabinet. Range Rating* 120/240 Volts 8.8 - 16.5 KW 16.6 - 22.5 KW 120/208 Volts 7.8 - 12.5 KW 12.6 - 18.5 KW Specified... electrical voltage and frequency as specified on the oven frame behind the control panel or on the model/serial number rating plate. or 50-amp power supply cord (pigtail) (see following Range Rating chart). See the "Electrical Connection" section. ■ Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack ...
Installation Instructions
Page 9
...8328;" nut driver to connect the neutral (white) wire to the center terminal block post with ranges. 8. Green ground wire E. NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with one of ... to the terminal block. A B C D A. C D A. Power supply cord wires - Line 2 (red) D D. NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening, with ring...
...8328;" nut driver to connect the neutral (white) wire to the center terminal block post with ranges. 8. Green ground wire E. NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with one of ... to the terminal block. A B C D A. C D A. Power supply cord wires - Line 2 (red) D D. NOTE: For power supply cord replacement, use only a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening, with ring...