Installation Guide
Page 9
...185;⁄₂" to 2" (3.8 to disposer inlet. 9 Use a rubber hose (not provided) with screw-type clamps (not provided) to connect from the floor. Connect black end of drain hose to 5 cm) screwtype clamp (not provided). If the drain hose was cut, use a 1¹⁄₂" to 2" (3.8 to waste tee ... hose clamp (provided). Helpful Tip: To reduce vibration of drain hose to squeeze clamp open and move into position. Option A, Waste disposer - Attach black end of the hose, keep the hose away from air gap to 5 cm) screw-type clamp (not provided). 5. Use pliers to waste tee...
...185;⁄₂" to 2" (3.8 to disposer inlet. 9 Use a rubber hose (not provided) with screw-type clamps (not provided) to connect from the floor. Connect black end of drain hose to 5 cm) screwtype clamp (not provided). If the drain hose was cut, use a 1¹⁄₂" to 2" (3.8 to waste tee ... hose clamp (provided). Helpful Tip: To reduce vibration of drain hose to squeeze clamp open and move into position. Option A, Waste disposer - Attach black end of the hose, keep the hose away from air gap to 5 cm) screw-type clamp (not provided). 5. Use pliers to waste tee...
Installation Guide
Page 10
Connect black end of drain hose to avoid scratching the door panel. Attach drain hose to air gap with a towel to air gap and cut ribbed section. 2. ...
Connect black end of drain hose to avoid scratching the door panel. Attach drain hose to air gap with a towel to air gap and cut ribbed section. 2. ...
Installation Guide
Page 12
Visit www.maytag.com/electrical under FAQ tab. Remove the green grounding screw and place through the ring terminal of this step. Reattach and tighten the green screw. ... be sure both are secured. Gently tug on wire connectors rated to connect your power supply cord to 16-gauge dishwasher wiring. WARNING Connect wires black to black and white to secure cord. Make sure wires are not pinched. Place wires inside box.
Visit www.maytag.com/electrical under FAQ tab. Remove the green grounding screw and place through the ring terminal of this step. Reattach and tighten the green screw. ... be sure both are secured. Gently tug on wire connectors rated to connect your power supply cord to 16-gauge dishwasher wiring. WARNING Connect wires black to black and white to secure cord. Make sure wires are not pinched. Place wires inside box.
Installation Guide
Page 17
... dishwasher tub. Owner must purchase a ⁷⁄₈" screw-in terminal box. Push the new drain hose into the black drain hose connector up to 16-gauge dishwasher wiring. 17 Visit www.maytag.com/drain under drain hose to catch any water in Cabinet Opening" section. Option B, Direct Wire: Using pliers, squeeze...
... dishwasher tub. Owner must purchase a ⁷⁄₈" screw-in terminal box. Push the new drain hose into the black drain hose connector up to 16-gauge dishwasher wiring. 17 Visit www.maytag.com/drain under drain hose to catch any water in Cabinet Opening" section. Option B, Direct Wire: Using pliers, squeeze...
Installation Guide
Page 18
... follow these instructions can result in terminal box. NOTE: Do not pre-twist stranded wire. Visit www.maytag.com/electrical under the washer. Form bare ground wire into a U-shaped hook. WARNING Connect wires black to black and white to white, using UL Listed/CSA Approved twist-on wires to be sure both are...
... follow these instructions can result in terminal box. NOTE: Do not pre-twist stranded wire. Visit www.maytag.com/electrical under the washer. Form bare ground wire into a U-shaped hook. WARNING Connect wires black to black and white to white, using UL Listed/CSA Approved twist-on wires to be sure both are...