Dimension Guide
Page 1
...supply line (¹⁄₂" minimum plastic tubing is connected to waste tee or disposer inlet above drain trap in the cabinet next to the waste tee or disposer inlet. Follow the kit instructions for your dishwasher. If this is not long enough, use ... Supply Requirements: A hot water line with a maximum length of the dishwasher. Water temperature must meet all models) B. Do not solder within 6" (15.2 cm) from water inlet valve. drain line fittings. PRODUCT DIMENSIONS (62.2 cm) B (60.6 cm) (6287.8Cc"m) 30" (834.37Dc"m) 3 "-4 " (8.8 cm -10.6 cm) 3" (9.4 cm) A....
...supply line (¹⁄₂" minimum plastic tubing is connected to waste tee or disposer inlet above drain trap in the cabinet next to the waste tee or disposer inlet. Follow the kit instructions for your dishwasher. If this is not long enough, use ... Supply Requirements: A hot water line with a maximum length of the dishwasher. Water temperature must meet all models) B. Do not solder within 6" (15.2 cm) from water inlet valve. drain line fittings. PRODUCT DIMENSIONS (62.2 cm) B (60.6 cm) (6287.8Cc"m) 30" (834.37Dc"m) 3 "-4 " (8.8 cm -10.6 cm) 3" (9.4 cm) A....
Installation Guide
Page 6
...that the electrical connection and wire size are connecting the air gap, a rubber hose (not provided) will be connected to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm) minimum above subfloor or floor. • Use ¹⁄₂" minimum ...kit (Part Number 4317824) marked for your dishwasher. It is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the water inlet valve. 6 A copy of 12' (3.7 m) (Part Number 3385556) that meets all current AHAM/IAPMO test standards, is recommended that meets the wiring requirements ...
...that the electrical connection and wire size are connecting the air gap, a rubber hose (not provided) will be connected to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm) minimum above subfloor or floor. • Use ¹⁄₂" minimum ...kit (Part Number 4317824) marked for your dishwasher. It is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the water inlet valve. 6 A copy of 12' (3.7 m) (Part Number 3385556) that meets all current AHAM/IAPMO test standards, is recommended that meets the wiring requirements ...
Installation Guide
Page 9
...9 NOTE: To avoid vibration during operation, route the water supply line so that could clog the inlet valve. Connect the ³⁄₈" compression fitting to the water supply line prior to the dishwasher inlet on the front left side of E.I. Flush water into a shallow pan until clear to get rid... it does not touch the dishwasher base, frame or motor. 6 Add 90° elbow fitting to the water supply line Slowly turn water shutoff valve to "OFF" position. NOTE: Do not use Teflon®† tape with compression fittings. †® Teflon is facing upward as it will...
...9 NOTE: To avoid vibration during operation, route the water supply line so that could clog the inlet valve. Connect the ³⁄₈" compression fitting to the water supply line prior to the dishwasher inlet on the front left side of E.I. Flush water into a shallow pan until clear to get rid... it does not touch the dishwasher base, frame or motor. 6 Add 90° elbow fitting to the water supply line Slowly turn water shutoff valve to "OFF" position. NOTE: Do not use Teflon®† tape with compression fittings. †® Teflon is facing upward as it will...
Use & Care Guide
Page 14
...is blinking, the load is loaded correctly. Blinking LED's can occur periodically throughout the cycle while the dishwasher is draining. ■ Normal water valve hissing may be heard when the detergent dispenser opens during a heated wash cycle, the cycle will end and the Clean LED will not come... "Troubleshooting.") Be sure the cycle has completed (the Clean light is on . The Heavy Duty cycle with water. Scrape food from the disposer inlet. In this case, the Start/Resume button LED, the Cycle Status Indicator LED(s), and the countdown bars on some models) for kinks in the...
...is blinking, the load is loaded correctly. Blinking LED's can occur periodically throughout the cycle while the dishwasher is draining. ■ Normal water valve hissing may be heard when the detergent dispenser opens during a heated wash cycle, the cycle will end and the Clean LED will not come... "Troubleshooting.") Be sure the cycle has completed (the Clean light is on . The Heavy Duty cycle with water. Scrape food from the disposer inlet. In this case, the Start/Resume button LED, the Cycle Status Indicator LED(s), and the countdown bars on some models) for kinks in the...