Owner's Manual (pdf)
Page 2
..., there is connected. • Consult the dealer or an experienced radio/TV technician for a Class B digital device, pursuant to Part 15 of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between... the equipment and receiver. • Connect the equipment into an outlet on , the user is encouraged to try to correct the interference by turning the equipment off the power immediately and consult your Kenwood...
..., there is connected. • Consult the dealer or an experienced radio/TV technician for a Class B digital device, pursuant to Part 15 of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between... the equipment and receiver. • Connect the equipment into an outlet on , the user is encouraged to try to correct the interference by turning the equipment off the power immediately and consult your Kenwood...
Owner's Manual (pdf)
Page 3
... iron plate by using Grommets. • Connect the ground wire to a metal part of the car chassis that acts as the unit's fuse capacity or somewhat larger. • For the power cord and ground, use a vehicle type (fireproof ) power wring cord with a current capacity greater than the unit's fuse capacity. (Use...cord with the range of 14 mm² (AWG 6) to 21 mm² (AWG 4). • When more than one power amplifier are going to be used, use a power supply wiring wire and protective fuse of the4Ωspeakers and then connect suitable speakers to be emitted as well as paint thinner ...
... iron plate by using Grommets. • Connect the ground wire to a metal part of the car chassis that acts as the unit's fuse capacity or somewhat larger. • For the power cord and ground, use a vehicle type (fireproof ) power wring cord with a current capacity greater than the unit's fuse capacity. (Use...cord with the range of 14 mm² (AWG 6) to 21 mm² (AWG 4). • When more than one power amplifier are going to be used, use a power supply wiring wire and protective fuse of the4Ωspeakers and then connect suitable speakers to be emitted as well as paint thinner ...
Owner's Manual (pdf)
Page 4
... the negative · terminal of the amplifier will not obstruct driving. Connect the speaker wires. 5. Install the remote controller. 9. Install the amplifier in a location which it will become hot... power control wire and grounding wire following this unit in a place where people, resins, and other damage. • Do not install near the dashboard, rear tray, or air bag safety parts... (9/16") or more) CAUTION • Do not install in the unit. 7. Install the installation fittings in the below locations; (Unstable location, In a location that interferes with it may be careful not...
... the negative · terminal of the amplifier will not obstruct driving. Connect the speaker wires. 5. Install the remote controller. 9. Install the amplifier in a location which it will become hot... power control wire and grounding wire following this unit in a place where people, resins, and other damage. • Do not install near the dashboard, rear tray, or air bag safety parts... (9/16") or more) CAUTION • Do not install in the unit. 7. Install the installation fittings in the below locations; (Unstable location, In a location that interferes with it may be careful not...
Owner's Manual (pdf)
Page 5
■ Remote controller (Accessory of KAC-X1D, Optional accessory for XR-1S.) Mounting bracket Remote controller Self-tapping screw (ø2.6 × 12 mm (1/8" × 1/2")) ■ Accessories Part name Remote cable (6.0 m : 19.7 ft) External View Number of Items 1 Remote controller 1 Mounting bracket 1 Self-tapping screws (ø2.6 × 12 mm (1/8" × 1/2")) 2 English
■ Remote controller (Accessory of KAC-X1D, Optional accessory for XR-1S.) Mounting bracket Remote controller Self-tapping screw (ø2.6 × 12 mm (1/8" × 1/2")) ■ Accessories Part name Remote cable (6.0 m : 19.7 ft) External View Number of Items 1 Remote controller 1 Mounting bracket 1 Self-tapping screws (ø2.6 × 12 mm (1/8" × 1/2")) 2 English
Owner's Manual (pdf)
Page 6
.... SPEAKER OUTPUT REMOTE LINE IN LINE OUT L R Hexagon Wrench (Small) Right input Use the attached Hexagon Wrench. CENTER UNIT (CD receiver, etc.) * Commercially available parts RCA cable* Power control wire* Left input Hexagon Wrench (Small) FUSE [30Ax2] BATT. Connection WARNING Remove the ignition key and disconnect the negative · terminal of the...
.... SPEAKER OUTPUT REMOTE LINE IN LINE OUT L R Hexagon Wrench (Small) Right input Use the attached Hexagon Wrench. CENTER UNIT (CD receiver, etc.) * Commercially available parts RCA cable* Power control wire* Left input Hexagon Wrench (Small) FUSE [30Ax2] BATT. Connection WARNING Remove the ignition key and disconnect the negative · terminal of the...
Owner's Manual (pdf)
Page 9
...3. Turn the LINE OUT FILTER switch ON. Remote cable CENTER UNIT (CD receiver, etc.) RCA cable* Power control wire* Remote controller FUSE [30Ax2] BATT. GND P.CON Slave amplifier SPEAKER OUTPUT REMOTE LINE IN LINE OUT L R REMOTE LINE IN LINE OUT L R LINE OUT FILTER...XR-1S.) CAUTION • Before connecting the remote controller cables, always turn the Bass boost level knob all the way to the left. GND P.CON Slave amplifier SPEAKER OUTPUT Hexagon Wrench (Small) Use the attached FUSE [30Ax2] Hexagon Wrench. * Commercially available parts ■ Multi Amplifier...
...3. Turn the LINE OUT FILTER switch ON. Remote cable CENTER UNIT (CD receiver, etc.) RCA cable* Power control wire* Remote controller FUSE [30Ax2] BATT. GND P.CON Slave amplifier SPEAKER OUTPUT REMOTE LINE IN LINE OUT L R REMOTE LINE IN LINE OUT L R LINE OUT FILTER...XR-1S.) CAUTION • Before connecting the remote controller cables, always turn the Bass boost level knob all the way to the left. GND P.CON Slave amplifier SPEAKER OUTPUT Hexagon Wrench (Small) Use the attached FUSE [30Ax2] Hexagon Wrench. * Commercially available parts ■ Multi Amplifier...