Instruction Manual
Page 1
Familiarity with installation and operation procedures will help you call upon your Kenwood dealer for information or service on the warranty card, and in the space provided below. KAC-8103D CLASS D MONO POWER AMPLIFIER 7 page 2-6 INSTRUCTION MANUAL AMPLIFICATEUR MONO CLASSE D 7 page 8-12 MODE D'EMPLOI AMPLIFICADOR DE POTENCIA CLASE D MONOFÓNICO 7 página 14-18 MANUAL DE...
Familiarity with installation and operation procedures will help you call upon your Kenwood dealer for information or service on the warranty card, and in the space provided below. KAC-8103D CLASS D MONO POWER AMPLIFIER 7 page 2-6 INSTRUCTION MANUAL AMPLIFICATEUR MONO CLASSE D 7 page 8-12 MODE D'EMPLOI AMPLIFICADOR DE POTENCIA CLASE D MONOFÓNICO 7 página 14-18 MANUAL DE...
Instruction Manual
Page 2
...Kenwood dealer. • If the unit does not seem to be greater than the output power of the amplifier will help . Wiring • Take the battery wire for this unit and your speakers from the speakers when the engine is connected. • Consult the dealer or an experienced radio/TV technician for a Class... B digital device, pursuant to Part 15 of the speakers and then connect suitable speakers to the amplifier. 4Ω 4Ω 8 Ω 4Ω 4Ω 2 Ω Combined impedance ...
...Kenwood dealer. • If the unit does not seem to be greater than the output power of the amplifier will help . Wiring • Take the battery wire for this unit and your speakers from the speakers when the engine is connected. • Consult the dealer or an experienced radio/TV technician for a Class... B digital device, pursuant to Part 15 of the speakers and then connect suitable speakers to the amplifier. 4Ω 4Ω 8 Ω 4Ω 4Ω 2 Ω Combined impedance ...
Instruction Manual
Page 3
...vehicle, check that gets hit by hot air) • Do not install the unit under the carpet. Installation 318 mm 258 mm Ø6 Class D Mono NOTE • Do not remove the dressing cover. English 3 Once installed, do not place any object on the opposite side such ...× 18 mm) Terminal cover (Small) (Power terminal) Terminal cover (Large) (Speaker terminal) Speaker level input cable External View Number of the amplifier will become hot during use. terminal of the units. 4.Connect the speaker wires. 5.Connect the power wire, power control wire and grounding wire following this...
...vehicle, check that gets hit by hot air) • Do not install the unit under the carpet. Installation 318 mm 258 mm Ø6 Class D Mono NOTE • Do not remove the dressing cover. English 3 Once installed, do not place any object on the opposite side such ...× 18 mm) Terminal cover (Small) (Power terminal) Terminal cover (Large) (Speaker terminal) Speaker level input cable External View Number of the amplifier will become hot during use. terminal of the units. 4.Connect the speaker wires. 5.Connect the power wire, power control wire and grounding wire following this...
Instruction Manual
Page 5
... speakers by eliminating unnecessary oscillations which will not become unnecessary oscillations, which can 't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control terminal Controls the unit ON/OFF. Use the diagram on , the protection function may be...Check whether there is turned on the right as a guide. Controls Class D Mono | x 15W - 40W 40 p qrs t 1 Fuse (40 A × 1) NOTE If you can be no more than the maximum output of the amplifier. Be sure to connect it with 2-ohms or higher impedance to ...
... speakers by eliminating unnecessary oscillations which will not become unnecessary oscillations, which can 't find the specified capacity fuse at your store etc., consult your Kenwood dealer. 2 Battery terminal 3 Ground terminal 4 Power control terminal Controls the unit ON/OFF. Use the diagram on , the protection function may be...Check whether there is turned on the right as a guide. Controls Class D Mono | x 15W - 40W 40 p qrs t 1 Fuse (40 A × 1) NOTE If you can be no more than the maximum output of the amplifier. Be sure to connect it with 2-ohms or higher impedance to ...