Instruction Manual
Page 2
...8226; If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer. • Do not touch the unit during installation, consult your Kenwood dealer. • If the unit does not seem to be short-circuited. • When a speaker ... power and wipe the panel with a dry silicon cloth or soft cloth. 2CAUTION Do not wipe the panel with the wrong rating may be working right, consult your unit to the amplifier. 4Ω 4Ω 8 Ω 4Ω 4Ω 2 Ω Combined impedance 2 English terminal. Using a fuse with a hard ...
...8226; If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer. • Do not touch the unit during installation, consult your Kenwood dealer. • If the unit does not seem to be short-circuited. • When a speaker ... power and wipe the panel with a dry silicon cloth or soft cloth. 2CAUTION Do not wipe the panel with the wrong rating may be working right, consult your unit to the amplifier. 4Ω 4Ω 8 Ω 4Ω 4Ω 2 Ω Combined impedance 2 English terminal. Using a fuse with a hard ...
Instruction Manual
Page 4
...Protective Fuse* Battery Ground wire* Lead terminal* Right speaker Left speaker ■ Bridged Connections Speaker (Bridged) ■ Remote cable connection (KAC-7252 only) 2CAUTION • Before connecting the remote controller cables, always set the Bass boost level control to both RCA cable input jacks and ...cable Connections 2CAUTION • If sound is not output normally, immediately turn the power off before changing the setting of the same rating. • Check that the brake lamps, winkers, and wipers work properly. Sharing the negative wire of the speaker or grounding ...
...Protective Fuse* Battery Ground wire* Lead terminal* Right speaker Left speaker ■ Bridged Connections Speaker (Bridged) ■ Remote cable connection (KAC-7252 only) 2CAUTION • Before connecting the remote controller cables, always set the Bass boost level control to both RCA cable input jacks and ...cable Connections 2CAUTION • If sound is not output normally, immediately turn the power off before changing the setting of the same rating. • Check that the brake lamps, winkers, and wipers work properly. Sharing the negative wire of the speaker or grounding ...
Instruction Manual
Page 5
...KAC-7202 only) Sets the low frequency level to select the operation mode of the amplifier. • STEREO position: The amplifier can 't find the specified capacity fuse at your store etc., consult your Kenwood... be boosted. xy ^ OPERATION switch This switch is 4Ω or greater. 2CAUTION The rated input of the speakers should have an impedance of the genuineaccessory car stereo. The speakers to...The genuine-accessory car stereo shall have an impedance of the amplifier. With this may result. 6 REMOTE terminal (KAC-7252 only) Connects the Remote cable. Remove the cover to access ...
...KAC-7202 only) Sets the low frequency level to select the operation mode of the amplifier. • STEREO position: The amplifier can 't find the specified capacity fuse at your store etc., consult your Kenwood... be boosted. xy ^ OPERATION switch This switch is 4Ω or greater. 2CAUTION The rated input of the speakers should have an impedance of the genuineaccessory car stereo. The speakers to...The genuine-accessory car stereo shall have an impedance of the amplifier. With this may result. 6 REMOTE terminal (KAC-7252 only) Connects the Remote cable. Remove the cover to access ...
Instruction Manual
Page 6
... the combined impedance with the subwoofer. • Ensure that the withstand voltage and current ratings of the capacitors (C) and coils (L) are sufficient. The capacitor rating should be as close as possible to 331.25 (µF) and the coil rating should be as close as possible to 5.3 (mH). 2CAUTION • If you wish to... Principle of Tri-mode Method of frequency band division using speakers with an impedance of 4 ohms. Prepare commercially-available coil and capacitor with the closest ratings to the results calculated from the formula above.
... the combined impedance with the subwoofer. • Ensure that the withstand voltage and current ratings of the capacitors (C) and coils (L) are sufficient. The capacitor rating should be as close as possible to 331.25 (µF) and the coil rating should be as close as possible to 5.3 (mH). 2CAUTION • If you wish to... Principle of Tri-mode Method of frequency band division using speakers with an impedance of 4 ohms. Prepare commercially-available coil and capacitor with the closest ratings to the results calculated from the formula above.
Instruction Manual
Page 7
...200 Hz (variable) Bass Boost Circuit...0 - +18 dB (variable) 0 - +18 dB (variable) Bass Boost Frequency...40 - 100 Hz (variable) 40 Hz General ...KAC-7252 KAC-7202 Operating Voltage ...14.4 V (11 - 16 V allowable) 14.4 V (11 - 16 V allowable) Current Consumption ...40 A 40 A Installation Size (W ×... H × D) ...380 × 61 × 286 mm 380 × 61 × 286 mm Weight ...5.8 kg 5.7 kg English 7 Audio Section...KAC-7252 KAC-7202 Max Power Output...1000 W 920 W Rated Power Output (+B = 14.4 V) Normal (4 Ω) (20 Hz - 20 kHz, 0.08 % THD)...170 W × 2 150 W × 2 ...
...200 Hz (variable) Bass Boost Circuit...0 - +18 dB (variable) 0 - +18 dB (variable) Bass Boost Frequency...40 - 100 Hz (variable) 40 Hz General ...KAC-7252 KAC-7202 Operating Voltage ...14.4 V (11 - 16 V allowable) 14.4 V (11 - 16 V allowable) Current Consumption ...40 A 40 A Installation Size (W ×... H × D) ...380 × 61 × 286 mm 380 × 61 × 286 mm Weight ...5.8 kg 5.7 kg English 7 Audio Section...KAC-7252 KAC-7202 Max Power Output...1000 W 920 W Rated Power Output (+B = 14.4 V) Normal (4 Ω) (20 Hz - 20 kHz, 0.08 % THD)...170 W × 2 150 W × 2 ...