Owner's Manual (pdf)
Page 2
For safety's sake, leave the mounting and wiring work to be working right, consult your Kenwood dealer. Also avoid places with too much dust or the possibility of water splashing. • When replacing a fuse, only use a new one power amplifier are going to be the same capacity as the unit's fuse capacity ...8226; If you experience problems during use because the surface of the unit becomes hot and may cause your Kenwood dealer. 4Ω • If the unit does not seem to be used in Watts) of 2Ω or greater. CAUTION Do not wipe the panel with the4wΩ rong rating may ...
For safety's sake, leave the mounting and wiring work to be working right, consult your Kenwood dealer. Also avoid places with too much dust or the possibility of water splashing. • When replacing a fuse, only use a new one power amplifier are going to be the same capacity as the unit's fuse capacity ...8226; If you experience problems during use because the surface of the unit becomes hot and may cause your Kenwood dealer. 4Ω • If the unit does not seem to be used in Watts) of 2Ω or greater. CAUTION Do not wipe the panel with the4wΩ rong rating may ...
Owner's Manual (pdf)
Page 5
... it. • Do not mount the unit in a place where the ducts of the amplifier will become hot during use. When the protection function is triggered, the Power indicator goes OFF and the amplifier stops operating. • When a speaker wire may be short-circuited. • When a speaker output contacts ground. • When the unit...
... it. • Do not mount the unit in a place where the ducts of the amplifier will become hot during use. When the protection function is triggered, the Power indicator goes OFF and the amplifier stops operating. • When a speaker wire may be short-circuited. • When a speaker output contacts ground. • When the unit...
Owner's Manual (pdf)
Page 6
...before changing the setting of any switch. • If the fuse blows, check wires for this may cause malfunction or damage. Speaker level input connections • The genuine-accessory car stereo shall have a maximum power output of the car can cause this unit accepts speakers with a minimum impedance of ...of the same rating. • Check that no more than 40 W. CAUTION • If sound is not output normally, immediately turn the power off and check connections. • Be sure to both RCA cable input jacks and the speaker level input terminals simultaneously, for shorts, then replace...
...before changing the setting of any switch. • If the fuse blows, check wires for this may cause malfunction or damage. Speaker level input connections • The genuine-accessory car stereo shall have a maximum power output of the car can cause this unit accepts speakers with a minimum impedance of ...of the same rating. • Check that no more than 40 W. CAUTION • If sound is not output normally, immediately turn the power off and check connections. • Be sure to both RCA cable input jacks and the speaker level input terminals simultaneously, for shorts, then replace...
Owner's Manual (pdf)
Page 7
... LINE IN L R SPEAKER LEVEL INPUT RCA cable* Power control wire* LPF FREQUENCY[Hz] 150 100 70 50 200 INPUT SENSITIVITY[V] 2 1 0.5 3 0.3 4 [MIN] 5 0.2 [MAX] OFF ON BASS EXPANDER LINE IN L R SPEAKER LEVEL INPUT Genuine-accessory car stereo (No line output center unit etc.) ■ Power wire and Speaker wire connection Power control wire* (RCA cable connection) Speaker level input cable...
... LINE IN L R SPEAKER LEVEL INPUT RCA cable* Power control wire* LPF FREQUENCY[Hz] 150 100 70 50 200 INPUT SENSITIVITY[V] 2 1 0.5 3 0.3 4 [MIN] 5 0.2 [MAX] OFF ON BASS EXPANDER LINE IN L R SPEAKER LEVEL INPUT Genuine-accessory car stereo (No line output center unit etc.) ■ Power wire and Speaker wire connection Power control wire* (RCA cable connection) Speaker level input cable...
Owner's Manual (pdf)
Page 9
... speaker cord and fixing the cause of the terminals and wires well. A speaker wire is pinched by a screw in your unit may be...9 / · of the short, replace the fuse. Specifications CEA-2006 RMS Watts per channel @ 4 ohms, 1 % THD+N) Signal to Noise Ratio (Reference: 1Watt into 4 ohms) Audio Section Max Power Output Rated Power Output (+B = 14.4 V) (4 Ω) (20 Hz - 200 Hz, ... control is not set improperly. Set switches properly by referring to change without notice. 200 W × 1 75 dBA 600 W 200 W × 1 200 W × 1 300 W × 1 20 Hz - 200 Hz 0.2 V 5.0 ...
... speaker cord and fixing the cause of the terminals and wires well. A speaker wire is pinched by a screw in your unit may be...9 / · of the short, replace the fuse. Specifications CEA-2006 RMS Watts per channel @ 4 ohms, 1 % THD+N) Signal to Noise Ratio (Reference: 1Watt into 4 ohms) Audio Section Max Power Output Rated Power Output (+B = 14.4 V) (4 Ω) (20 Hz - 200 Hz, ... control is not set improperly. Set switches properly by referring to change without notice. 200 W × 1 75 dBA 600 W 200 W × 1 200 W × 1 300 W × 1 20 Hz - 200 Hz 0.2 V 5.0 ...