Owner's Manual (pdf)
Page 2
... which the receiver is encouraged to try to correct the interference by turning the equipment off the power immediately and consult your Kenwood dealer. • Do not touch the unit during installation, consult your Kenwood dealer. • If the unit does not seem to Part 15 of water splashing. •..., battery, or ground wires, make sure to use automotive-grade wires or other wires with Canadian ICES-003. Using a fuse with the wrong rating may generate or use a new one or more to prevent wire deterioration and damage to the wire coating. • To prevent a short circuit...
... which the receiver is encouraged to try to correct the interference by turning the equipment off the power immediately and consult your Kenwood dealer. • Do not touch the unit during installation, consult your Kenwood dealer. • If the unit does not seem to Part 15 of water splashing. •..., battery, or ground wires, make sure to use automotive-grade wires or other wires with Canadian ICES-003. Using a fuse with the wrong rating may generate or use a new one or more to prevent wire deterioration and damage to the wire coating. • To prevent a short circuit...
Owner's Manual (pdf)
Page 3
... function There is not connected. • Be sure to install a protective fuse in Watts) of the amplifier. Do not turn off . CAUTION Do not wipe the panel with a hard cloth ... wire to directly contact the edge of the iron plate by each amplifier. 7 Speaker Selection • The rated input power of the speakers that are going to be connected should be the...power amplifier are going to be used , use a power supply wiring wire and protective fuse of greater current-handling capacity than one set of speakers are going to be connected should be 2Ω or greater (for stereo...
... function There is not connected. • Be sure to install a protective fuse in Watts) of the amplifier. Do not turn off . CAUTION Do not wipe the panel with a hard cloth ... wire to directly contact the edge of the iron plate by each amplifier. 7 Speaker Selection • The rated input power of the speakers that are going to be connected should be the...power amplifier are going to be used , use a power supply wiring wire and protective fuse of greater current-handling capacity than one set of speakers are going to be connected should be 2Ω or greater (for stereo...
Owner's Manual (pdf)
Page 7
... well to select the proper setting and connection. 1. CAUTION • If sound is not output normally, immediately turn power off and check connections. • Be sure to turn the power off before changing the setting of any switch. • If the fuse blows, check wires for shorts, then replace... the fuse with one of the battery to prevent short circuits. 2. Remove the ignition key and disconnect the negative · terminal of the same rating. • ...
... well to select the proper setting and connection. 1. CAUTION • If sound is not output normally, immediately turn power off and check connections. • Be sure to turn the power off before changing the setting of any switch. • If the fuse blows, check wires for shorts, then replace... the fuse with one of the battery to prevent short circuits. 2. Remove the ignition key and disconnect the negative · terminal of the same rating. • ...
Owner's Manual (pdf)
Page 11
CEA-2006 RMS Watts per channel @ 4 ohms, 1 % THD+N 60 W × 2 Signal to Noise Ratio (Reference: 1Watt into 4 ohms 75 dBA Audio Section Max Power Output ...350 W Rated Power Output Normal (4 Ω) (20 Hz - 20 kHz, 1.0 % THD)...60 W × 2 (4 Ω) (DIN : 45324 , +B = 14.4V)...60 W × 2 (2 Ω) (1 kHz, 1.0 % THD)...75 W × 2 Bridged(4 Ω) (1 kHz, 1.0 % ...
CEA-2006 RMS Watts per channel @ 4 ohms, 1 % THD+N 60 W × 2 Signal to Noise Ratio (Reference: 1Watt into 4 ohms 75 dBA Audio Section Max Power Output ...350 W Rated Power Output Normal (4 Ω) (20 Hz - 20 kHz, 1.0 % THD)...60 W × 2 (4 Ω) (DIN : 45324 , +B = 14.4V)...60 W × 2 (2 Ω) (1 kHz, 1.0 % THD)...75 W × 2 Bridged(4 Ω) (1 kHz, 1.0 % ...