Owners Manual
Page 12
...If the chain is slack it is determined by Husqvarna. the wrong combination of bar and saw chain combinations we recommend. • Drive link width (mm/inches) • Number of teeth on bar tip sprocket (T). • Chain pitch (inches). See instructions under the heading Technical Data for... with a bar and chain combinations recommended by the length of the bar, the chain pitch and the number of drive links. 12 - Bar • Length (inches/cm) • Keep cutting equipment well lubricated and properly maintained! Faulty cutting equipment or ! By using cutting equipment with a...
...If the chain is slack it is determined by Husqvarna. the wrong combination of bar and saw chain combinations we recommend. • Drive link width (mm/inches) • Number of teeth on bar tip sprocket (T). • Chain pitch (inches). See instructions under the heading Technical Data for... with a bar and chain combinations recommended by the length of the bar, the chain pitch and the number of drive links. 12 - Bar • Length (inches/cm) • Keep cutting equipment well lubricated and properly maintained! Faulty cutting equipment or ! By using cutting equipment with a...
Owners Manual
Page 33
... noise level and to serious damage. • Undo the screw in the starter housing it is ok. • Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley and remove the pulley. Starter Loosen the screws (1 and 2). Care must be replaced...
... noise level and to serious damage. • Undo the screw in the starter housing it is ok. • Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley and remove the pulley. Starter Loosen the screws (1 and 2). Care must be replaced...
Owners Manual
Page 38
...displacement, cu.in/cm3 Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Recommended max. power, m/sec T435 2,15/35,2 1,57/40 1,10/28 2900 12500 1,5/2,0 @ 10000 Ikeda Denso CD NGK CMR7H 0,02/0,5 Walbro WT 804 0,55/0,26 3-9 0,36/0,17 Automatic 7,5/3,4 14"/35 12-16"/30-40 11-15"/28-38... 3/8" /9,52 0,050/1,3 Rim/6 19,1 38 - speed, rpm Power, kW/ rpm Ignition system Manufacturer of ignition system Type of ignition system Spark plug Electrode gap, inch/mm Fuel and lubrication system Manufacturer of carburetor Carburetor...
...displacement, cu.in/cm3 Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Recommended max. power, m/sec T435 2,15/35,2 1,57/40 1,10/28 2900 12500 1,5/2,0 @ 10000 Ikeda Denso CD NGK CMR7H 0,02/0,5 Walbro WT 804 0,55/0,26 3-9 0,36/0,17 Automatic 7,5/3,4 14"/35 12-16"/30-40 11-15"/28-38... 3/8" /9,52 0,050/1,3 Rim/6 19,1 38 - speed, rpm Power, kW/ rpm Ignition system Manufacturer of ignition system Type of ignition system Spark plug Electrode gap, inch/mm Fuel and lubrication system Manufacturer of carburetor Carburetor...
Owners Manual
Page 39
... or less kickback energy than in ANSI B 175.1-2000. Bar and chain combinations Recommended cutting equipment for chainsaw Husqvarna T435. Length, inch 12 14 16 Pitch, inch 3/8 3/8 3/8 Bar Gauge, inch 0,050 0,050 0,050 Max. The saw chain Husqvarna H36 is the chain saw models may use only the listed combinations of bars and chains for chain saw...
... or less kickback energy than in ANSI B 175.1-2000. Bar and chain combinations Recommended cutting equipment for chainsaw Husqvarna T435. Length, inch 12 14 16 Pitch, inch 3/8 3/8 3/8 Bar Gauge, inch 0,050 0,050 0,050 Max. The saw chain Husqvarna H36 is the chain saw models may use only the listed combinations of bars and chains for chain saw...