Operation Manual
Page 3
...64257;ts of cutting unit should be 12-15kg / 26.5-33 lb). Service journal Pre-delivery service 1 Charge the battery for the hydrostat pedals. 11 Check the engine ... bar, 9 PSI). 4 Adjust cutting unit: Adjust lift springs (effective weight of following the service schedule. Pre-delivery service carried out. No outstanding problems. Certified: Date, mileage, stamp, signature After the...start engine. 9 Check that rear edge is oil in neutral. 10 Check: Forward drive. Servicing and the in the gearbox. (Only AWD- English - 3 machines) 3 Check the synchronisation between...
...64257;ts of cutting unit should be 12-15kg / 26.5-33 lb). Service journal Pre-delivery service 1 Charge the battery for the hydrostat pedals. 11 Check the engine ... bar, 9 PSI). 4 Adjust cutting unit: Adjust lift springs (effective weight of following the service schedule. Pre-delivery service carried out. No outstanding problems. Certified: Date, mileage, stamp, signature After the...start engine. 9 Check that rear edge is oil in neutral. 10 Check: Forward drive. Servicing and the in the gearbox. (Only AWD- English - 3 machines) 3 Check the synchronisation between...
Operation Manual
Page 4
... rear wheels has been checked and adjusted in small or confined areas. Good service Husqvarna products are sold all over short distances and at all service work and repairs are acquainted with the relevant safety procedures. For example, before driving the...service procedures. Compliance with the equipment recommended by your machine is only valid if the synchronisation of the machine and even its particular characteristics and who are recorded. The last chapter in fluences the second-hand value of liability for choosing a Husqvarna Rider. Bring the operator's manual...
... rear wheels has been checked and adjusted in small or confined areas. Good service Husqvarna products are sold all over short distances and at all service work and repairs are acquainted with the relevant safety procedures. For example, before driving the...service procedures. Compliance with the equipment recommended by your machine is only valid if the synchronisation of the machine and even its particular characteristics and who are recorded. The last chapter in fluences the second-hand value of liability for choosing a Husqvarna Rider. Bring the operator's manual...
Operation Manual
Page 21
... a year X X X X X X X O O O X O O O Maintenance interval in dusty conditions. 3)First change after 8 hours X = Described in this manual, visit an authorised service workshop. The parking brake is used daily it should be ! Clean around the silencer Clean the prefilter in the air filter 2) Change... hours. 5)Replace the paper filter annually or every 200 hours. 6)Conducted by authorised service workshop. 7)Only 322T AWD first change the oil 6,7) in this operator's manual O = Not described in the tyres. conducted on the engine or cutting unit unless: The...
... a year X X X X X X X O O O X O O O Maintenance interval in dusty conditions. 3)First change after 8 hours X = Described in this manual, visit an authorised service workshop. The parking brake is used daily it should be ! Clean around the silencer Clean the prefilter in the air filter 2) Change... hours. 5)Replace the paper filter annually or every 200 hours. 6)Conducted by authorised service workshop. 7)Only 322T AWD first change the oil 6,7) in this operator's manual O = Not described in the tyres. conducted on the engine or cutting unit unless: The...
Operation Manual
Page 33
...General lubrication All joints and bearings are lubricated using the same type of grease *. Rider 220T Fill if necessary with oil Synthetic 10W/50 The oil and filter should be lubricated...). Lubricate using engine oil. With daily use , the machine should be changed by an authorised service representative, as described in the transmission's oil tank. Carry out this lubrication regularly; with daily use... adjuster The belt adjuster should be vented before the machine is oil in the Workshop Manual. Undo the two screws (one on cleanliness and the system must be carried out ...
...General lubrication All joints and bearings are lubricated using the same type of grease *. Rider 220T Fill if necessary with oil Synthetic 10W/50 The oil and filter should be lubricated...). Lubricate using engine oil. With daily use , the machine should be changed by an authorised service representative, as described in the transmission's oil tank. Carry out this lubrication regularly; with daily use... adjuster The belt adjuster should be vented before the machine is oil in the Workshop Manual. Undo the two screws (one on cleanliness and the system must be carried out ...
Operation Manual
Page 37
....28 Combi 112 1120 / 44.1 25-75/0.98-2.95 420 / 16,5 SD 48 1220 / 48 25-75/0.98-2.95 423 / 16,7 IMPORTANT INFORMATION When the service life of this product has been served and it is not valid if non genuine parts are valid on the basis of information in this... manual. The warranty is no legal claims are used it should be returned to the dealer or to implement improvements. Note that no longer used . 37 - ...
....28 Combi 112 1120 / 44.1 25-75/0.98-2.95 420 / 16,5 SD 48 1220 / 48 25-75/0.98-2.95 423 / 16,7 IMPORTANT INFORMATION When the service life of this product has been served and it is not valid if non genuine parts are valid on the basis of information in this... manual. The warranty is no legal claims are used it should be returned to the dealer or to implement improvements. Note that no longer used . 37 - ...