Owners Manual
Page 12
...better and last longer. LUBRICATION Keep unit well lubricated (See "LUBRICATION CHART"). To receive full value from the warranty, the operator must maintain tiller as instructed in the Service and Adjustments section of this manual should replace the spark plug, clean or replace air filter, and check tines... and belts for loose fasteners. Service more often when operating under a heavy load or in dirty or dusty conditions. Some adjustments will need to be...
...better and last longer. LUBRICATION Keep unit well lubricated (See "LUBRICATION CHART"). To receive full value from the warranty, the operator must maintain tiller as instructed in the Service and Adjustments section of this manual should replace the spark plug, clean or replace air filter, and check tines... and belts for loose fasteners. Service more often when operating under a heavy load or in dirty or dusty conditions. Some adjustments will need to be...
Owners Manual
Page 15
.... TIRE CARE CAUTION: When mounting tires, unless beads are not equal, tiller will be affected by reversing above procedure. SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from unit. • Replace belt guard by differences in fuel, temperature, altitude or load. CLEVIS PIN HANDLE..."HIGH" and "LOW" positions. • Retighten handle lock lever securely after adjusting. Pull wheel out from tiller about 1 inch. • Remove two (2) screws from side of belt guard. • Remove hex nut and washer from bottom of removal, remove hairpin clip and clevis pin from...
.... TIRE CARE CAUTION: When mounting tires, unless beads are not equal, tiller will be affected by reversing above procedure. SERVICE AND ADJUSTMENTS CAUTION: Disconnect spark plug wire from unit. • Replace belt guard by differences in fuel, temperature, altitude or load. CLEVIS PIN HANDLE..."HIGH" and "LOW" positions. • Retighten handle lock lever securely after adjusting. Pull wheel out from tiller about 1 inch. • Remove two (2) screws from side of belt guard. • Remove hex nut and washer from bottom of removal, remove hairpin clip and clevis pin from...
Owners Manual
Page 18
...wear. CAUTION: Never store the tiller with clean oil. (See "ENGINE" in fuel tank or storage container. TILLER • Clean entire tiller (See "CLEANING" in the Maintenance section of this manual). • Inspect and replace belts, if necessary (See belt replacement instructions in the Service and ... cover that all rusted or chipped paint surfaces; STORAGE Immediately prepare your tiller for storage at least 10 minutes after adding stablizer to allow the stabilizer to rust. IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM. 18 OTHER • ...
...wear. CAUTION: Never store the tiller with clean oil. (See "ENGINE" in fuel tank or storage container. TILLER • Clean entire tiller (See "CLEANING" in the Maintenance section of this manual). • Inspect and replace belts, if necessary (See belt replacement instructions in the Service and ... cover that all rusted or chipped paint surfaces; STORAGE Immediately prepare your tiller for storage at least 10 minutes after adding stablizer to allow the stabilizer to rust. IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM. 18 OTHER • ...
Owners Manual
Page 19
... Operation section. 3. Dirty engine air screen. 11. Ground too dry and hard. 1. Inspect/adjust V-belt. 3. Dirty air cleaner. 5. Clean or replace air cleaner cartridge. 3. Engage drive control. 2. Engine runs but tiller won't move 1. Hard to shift gears. Clean or replace air cleaner cartridge. 3. Empty fuel tank ... TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not start Hard to start . 4. Bad spark plug or improper gap. 9. Clean engine air screen. 11. V-belt not correctly adjusted. 3. Carburetor out of fuel. 2. Tiller shuts off pulley(s). 1.
... Operation section. 3. Dirty engine air screen. 11. Ground too dry and hard. 1. Inspect/adjust V-belt. 3. Dirty air cleaner. 5. Clean or replace air cleaner cartridge. 3. Engage drive control. 2. Engine runs but tiller won't move 1. Hard to shift gears. Clean or replace air cleaner cartridge. 3. Empty fuel tank ... TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not start Hard to start . 4. Bad spark plug or improper gap. 9. Clean engine air screen. 11. V-belt not correctly adjusted. 3. Carburetor out of fuel. 2. Tiller shuts off pulley(s). 1.
Parts Manual
Page 3
...Belt...532 44 04-38 Guard, Belt MAINFRAME?LEFT? KEY PART NO. H. 36 532 10 23-31 Bracket, Reinforcement, L. inches. 1 inch = 25.4 mm 3 NO. MODEL NUMBER DRT900H (96093001202), PRODUCT NUMBER 960 ...93 00-12 MAINFRAME, LEFT SIDE KEY NO. 3 4 5 6 7 8 9 10 12 13 14 15 16 19 21 22 23 24 25 26 PART NO. DESCRIPTION 27 532 13 28-01 Belt...Belt Engine NOTE: All component dimensions given in U.S. REPAIR PARTS...
...Belt...532 44 04-38 Guard, Belt MAINFRAME?LEFT? KEY PART NO. H. 36 532 10 23-31 Bracket, Reinforcement, L. inches. 1 inch = 25.4 mm 3 NO. MODEL NUMBER DRT900H (96093001202), PRODUCT NUMBER 960 ...93 00-12 MAINFRAME, LEFT SIDE KEY NO. 3 4 5 6 7 8 9 10 12 13 14 15 16 19 21 22 23 24 25 26 PART NO. DESCRIPTION 27 532 13 28-01 Belt...Belt Engine NOTE: All component dimensions given in U.S. REPAIR PARTS...