Owners Manual
Page 12
... as instructed in the Service and Adjustments section of this manual should replace the spark plug, clean or replace air filter, and check tines and belts for loose fasteners. Some adjustments will need to operator abuse or negligence. All adjustments in this tiller does not cover items that have been subjected...
... as instructed in the Service and Adjustments section of this manual should replace the spark plug, clean or replace air filter, and check tines and belts for loose fasteners. Some adjustments will need to operator abuse or negligence. All adjustments in this tiller does not cover items that have been subjected...
Owners Manual
Page 15
... contact your tilling conditions. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. tire_3 HAIRPIN CLIP Fig. 23 TO REMOVE BELT GUARD (See Fig. 24) NOTE: For ease of gasoline or oil which can cause an explosion. Handle height will pull to keep ... "HIGH" and "LOW" positions. • Retighten handle lock lever securely after adjusting. If tire pressures are seated, overinflation can damage rubber. BELT GUARD SCREW AND WASHER HEX NUT AND WASHER (LOCATED BEHIND TIRE) SCREW AND WASHER HAIRPIN CLIP AND CLEVIS PIN Fig. 24 • Maintain 20...
... contact your tilling conditions. OVERSPEEDING THE ENGINE ABOVE THE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. tire_3 HAIRPIN CLIP Fig. 23 TO REMOVE BELT GUARD (See Fig. 24) NOTE: For ease of gasoline or oil which can cause an explosion. Handle height will pull to keep ... "HIGH" and "LOW" positions. • Retighten handle lock lever securely after adjusting. If tire pressures are seated, overinflation can damage rubber. BELT GUARD SCREW AND WASHER HEX NUT AND WASHER (LOCATED BEHIND TIRE) SCREW AND WASHER HAIRPIN CLIP AND CLEVIS PIN Fig. 24 • Maintain 20...
Owners Manual
Page 16
...MORE TENSION 16 This tension can be attained as described below. • Replace belt guard. • Reposition wheel and replace clevis pin and hairpin clip. NOTE POSITION OF BELT TO GUIDES. • Check belt adjustment as follows: • Loosen cable clip screw securing the drive control cable...8226; Tighten cable clip screw securely. SERVICE AND ADJUSTMENTS TO REPLACE GROUND DRIVE BELT (See Figs. 24 and 25) • Remove belt guard as described in "TO REMOVE BELT GUARD". • Remove old belt by slipping off engine pulley first then remove from transmission pulley. • ...
...MORE TENSION 16 This tension can be attained as described below. • Replace belt guard. • Reposition wheel and replace clevis pin and hairpin clip. NOTE POSITION OF BELT TO GUIDES. • Check belt adjustment as follows: • Loosen cable clip screw securing the drive control cable...8226; Tighten cable clip screw securely. SERVICE AND ADJUSTMENTS TO REPLACE GROUND DRIVE BELT (See Figs. 24 and 25) • Remove belt guard as described in "TO REMOVE BELT GUARD". • Remove old belt by slipping off engine pulley first then remove from transmission pulley. • ...
Owners Manual
Page 18
TILLER • Clean entire tiller (See "CLEANING" in the Maintenance section of this manual). • Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual). • Lubricate as shown in the Maintenance section of this manual). Inspect moving parts ...
TILLER • Clean entire tiller (See "CLEANING" in the Maintenance section of this manual). • Inspect and replace belts, if necessary (See belt replacement instructions in the Service and Adjustments section of this manual). • Lubricate as shown in the Maintenance section of this manual). Inspect moving parts ...
Owners Manual
Page 19
...Clean cylinder fins, air screen, and muffler area. 4. Remove and clean muffler. 5. Tine control is off when tine control engaged 1. V-belt is not engaged. 2. when tilling 2. Forward rotating tine drive should only be used for soft ground or for shallower tilling. 2. Shift to... Dirty engine air screen. 11. Empty and clean fuel tank and refill, and clean carburetor. 6. Wait for more favorable soil conditions. V-belt not correctly adjusted. 3. Drag Stake not lowered in fuel. 6. TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not start Hard to start . 4. ...
...Clean cylinder fins, air screen, and muffler area. 4. Remove and clean muffler. 5. Tine control is off when tine control engaged 1. V-belt is not engaged. 2. when tilling 2. Forward rotating tine drive should only be used for soft ground or for shallower tilling. 2. Shift to... Dirty engine air screen. 11. Empty and clean fuel tank and refill, and clean carburetor. 6. Wait for more favorable soil conditions. V-belt not correctly adjusted. 3. Drag Stake not lowered in fuel. 6. TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not start Hard to start . 4. ...
Parts Manual
Page 3
...76 05-24 Bolt, Hex 5/16-18 x 1-1/2 68 873 51 06-00 Nut Keps Hex 3/8-16 unc 69 532 16 41-73 Keeper Belt Engine NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm 3 NO. H. 36 532 10 23-31 Bracket, ... 12 47-18 Tire Valve 532 12 68-75 Rivet, Drilled 532 12 47-88 Clip, Hairpin 532 44 04-38 Guard, Belt MAINFRAME?LEFT? KEY PART NO. MODEL NUMBER DRT900H (96093001202), PRODUCT NUMBER 960 93 00-12 MAINFRAME, LEFT SIDE KEY NO. 3 4 5 6 7...
...76 05-24 Bolt, Hex 5/16-18 x 1-1/2 68 873 51 06-00 Nut Keps Hex 3/8-16 unc 69 532 16 41-73 Keeper Belt Engine NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm 3 NO. H. 36 532 10 23-31 Bracket, ... 12 47-18 Tire Valve 532 12 68-75 Rivet, Drilled 532 12 47-88 Clip, Hairpin 532 44 04-38 Guard, Belt MAINFRAME?LEFT? KEY PART NO. MODEL NUMBER DRT900H (96093001202), PRODUCT NUMBER 960 93 00-12 MAINFRAME, LEFT SIDE KEY NO. 3 4 5 6 7...