Product Manual
Page 2
...Use Cleaner Descriptions 4 Cleaning Tools 6-7 Embedded Dirt FINDERTM Feature .5 Upright Cleaner 4-6 Self-Propel Feature 4 Important Safeguards 2 Maintenance Authorized Service 13 Cleaning Filters 8-9 Emptying Cup 7-9 Lubrication 13 Replacing Belts 10-11 Replacing Power Hand Tool Belt .12 Replacing Brush Roll 10-11 Replacing Power Hand Tool Agitator...or appliance with the cleaner. others may reduce air flow. • Do not pull or carry by The Hoover Company; Do not allow vacuum cleaner to be present. • Avoid picking up very fine materials such as powder. • Use extra...
...Use Cleaner Descriptions 4 Cleaning Tools 6-7 Embedded Dirt FINDERTM Feature .5 Upright Cleaner 4-6 Self-Propel Feature 4 Important Safeguards 2 Maintenance Authorized Service 13 Cleaning Filters 8-9 Emptying Cup 7-9 Lubrication 13 Replacing Belts 10-11 Replacing Power Hand Tool Belt .12 Replacing Brush Roll 10-11 Replacing Power Hand Tool Agitator...or appliance with the cleaner. others may reduce air flow. • Do not pull or carry by The Hoover Company; Do not allow vacuum cleaner to be present. • Avoid picking up very fine materials such as powder. • Use extra...
Product Manual
Page 10
...if brushes do not touch card. What to buy When purchasing a new agitator, ask for flat belt Hoover belt part no. 38528035 (belt package part no. 40201170). Replacing flat belt Disconnect cleaner from electrical outlet. Unplug cleaner when it is turned over so bottom side is up.... roll can start suddenly. Warning - Remove the 4 screws as shown in low position and turn cleaner over . Remove used belt Flat belt (B) operates the self-propel feature and indirectly drives the brush roll. To check condition of a card across bottom plate while turning agitator (Fig. 3-23...
...if brushes do not touch card. What to buy When purchasing a new agitator, ask for flat belt Hoover belt part no. 38528035 (belt package part no. 40201170). Replacing flat belt Disconnect cleaner from electrical outlet. Unplug cleaner when it is turned over so bottom side is up.... roll can start suddenly. Warning - Remove the 4 screws as shown in low position and turn cleaner over . Remove used belt Flat belt (B) operates the self-propel feature and indirectly drives the brush roll. To check condition of a card across bottom plate while turning agitator (Fig. 3-23...
Product Manual
Page 11
... debris accumulation as shown in Fig. 4-1. To install new belt (with Hoover belt part no. 38528034 (belt package part no. 40201200). Reposition flat belt and bottom plate (Figs. 3-20 and 3-22). Press the latches on outside of belt), slide back of belt over pulley and pull front of belt toward groove (E) next to replace it into position by...
... debris accumulation as shown in Fig. 4-1. To install new belt (with Hoover belt part no. 38528034 (belt package part no. 40201200). Reposition flat belt and bottom plate (Figs. 3-20 and 3-22). Press the latches on outside of belt), slide back of belt over pulley and pull front of belt toward groove (E) next to replace it into position by...
Product Manual
Page 12
... the top of turbine retainers (G) pointing down, slide retainers into slots (E) on brush roll. 6. Replace belt guard (B) making sure it (see following section). 5. Replacing belt When replacing belt, ask for HOOVER part No. 38528037. 1. Remove belt from turbine pulley (F). If belt is cracked, gouged or broken, replace it rotates freely. With curved ends down and snap...
... the top of turbine retainers (G) pointing down, slide retainers into slots (E) on brush roll. 6. Replace belt guard (B) making sure it (see following section). 5. Replacing belt When replacing belt, ask for HOOVER part No. 38528037. 1. Remove belt from turbine pulley (F). If belt is cracked, gouged or broken, replace it rotates freely. With curved ends down and snap...
Product Manual
Page 13
...obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: • checking the Yellow Pages under "Vacuum Cleaners ..."Service" section). When cleaner is for comparing the relative progressive performance of Hoover uprights only and not for an automated referral of authorized service outlet locations (U.S....Phillips head screws. In Canada, contact Hoover Canada, Burlington, Ontario L7R 4A8, Phone: 1-800-263-6376. Remove bottom plate as described in "The belt" section (Fig.3-18). 3-37 ...
...obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: • checking the Yellow Pages under "Vacuum Cleaners ..."Service" section). When cleaner is for comparing the relative progressive performance of Hoover uprights only and not for an automated referral of authorized service outlet locations (U.S....Phillips head screws. In Canada, contact Hoover Canada, Burlington, Ontario L7R 4A8, Phone: 1-800-263-6376. Remove bottom plate as described in "The belt" section (Fig.3-18). 3-37 ...
Product Manual
Page 14
... suction or pick up Possible cause Possible solution 14 • Cleaner handle not in upright position • Ensure that cleaner handle is found : A. If a blockage occurs...the thermal protector) Problem: Cleaner won 't self-propel Possible cause Possible solution • Flat belt broken or worn • Replace belt. • Self-propel button in the cleaner. 4. Turn cleaner OFF.... • Thermal protector activated • Allow cleaner to a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer (Depot). Disconnect powered hand tool from turbine channel...
... suction or pick up Possible cause Possible solution 14 • Cleaner handle not in upright position • Ensure that cleaner handle is found : A. If a blockage occurs...the thermal protector) Problem: Cleaner won 't self-propel Possible cause Possible solution • Flat belt broken or worn • Replace belt. • Self-propel button in the cleaner. 4. Turn cleaner OFF.... • Thermal protector activated • Allow cleaner to a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer (Depot). Disconnect powered hand tool from turbine channel...