Specifications
Page 19
Deskstar 7K80 Hard Disk Drive specification 15 2.0 General features of the drive • Formatted capacities of 40 GB and 80 GB • Spindle speeds of 7200 RPM • Fluid Dynamic Bearing motor • Enhanced IDE interface • Sector format of 512 bytes/sector •...(133 MB/s) • CHS and LBA mode • Power saving modes/Low RPM idle mode (APM) • S.M.A.R.T. (Self Monitoring and Analysis Reporting Technology) • Support security feature • Quiet Seek mode (AAM) • 48-bit addressing feature • Adaptive BPI • ATA-7 compliant • UDMA 133...
Deskstar 7K80 Hard Disk Drive specification 15 2.0 General features of the drive • Formatted capacities of 40 GB and 80 GB • Spindle speeds of 7200 RPM • Fluid Dynamic Bearing motor • Enhanced IDE interface • Sector format of 512 bytes/sector •...(133 MB/s) • CHS and LBA mode • Power saving modes/Low RPM idle mode (APM) • S.M.A.R.T. (Self Monitoring and Analysis Reporting Technology) • Support security feature • Quiet Seek mode (AAM) • 48-bit addressing feature • Adaptive BPI • ATA-7 compliant • UDMA 133...
Specifications
Page 75
...page 81 for details. This command does not support 80h as that the device is in Section 8.3 below. 8.2 Terminology Device Host Device indicates HDS7280x0PLATy0 Host indicates the system that of the HDS7280x0PLATy0 hard disk drive. Download Download command is aborted when teh device... following deviations: Check Power Mode Check Power Mode command returns FFh to section 10.1, "Reset response" on reset. Deskstar 7K80 Hard Disk Drive Specification 71 The interface conforms to the Working Document of Information technology, AT Attachment with Packet Interface Extension (ATA/ATAPI...
...page 81 for details. This command does not support 80h as that the device is in Section 8.3 below. 8.2 Terminology Device Host Device indicates HDS7280x0PLATy0 Host indicates the system that of the HDS7280x0PLATy0 hard disk drive. Download Download command is aborted when teh device... following deviations: Check Power Mode Check Power Mode command returns FFh to section 10.1, "Reset response" on reset. Deskstar 7K80 Hard Disk Drive Specification 71 The interface conforms to the Working Document of Information technology, AT Attachment with Packet Interface Extension (ATA/ATAPI...
Specifications
Page 83
.... If the device detects an error while processing a command, RDY is set to 0 by the device in spite of the drive not spinning up. Device Fault. This product does not support DF bit. When an error occurs, this bit is set to 1 even if the host is set back to determine the... may not see it indicates that the device is read by the host at which time the bit again indicates the current Seek complete status. Deskstar 7K80 Hard Disk Drive Specification 79
.... If the device detects an error while processing a command, RDY is set to 0 by the device in spite of the drive not spinning up. Device Fault. This product does not support DF bit. When an error occurs, this bit is set to 1 even if the host is set back to determine the... may not see it indicates that the device is read by the host at which time the bit again indicates the current Seek complete status. Deskstar 7K80 Hard Disk Drive Specification 79
Specifications
Page 88
HDS7280x0PLATy0 supports both Logical CHS Addressing Mode and LBA Addressing Mode as the first logical CHS addressed sector (cylinder 0, head 0, sector 1). Heads are numbered from 0 to the ...
HDS7280x0PLATy0 supports both Logical CHS Addressing Mode and LBA Addressing Mode as the first logical CHS addressed sector (cylinder 0, head 0, sector 1). Heads are numbered from 0 to the ...
Specifications
Page 92
... self-test log sector as described in the SMART self-test log data structure. Disabling SMART disables the delivering of reported errors is supported. If a device receives a firmware modification, all self-test log data is interrupted by SMART Execute Off-line Immediate command. The...self-test features which are updated accordingly during the self-tests, the device services the host command. If it is discarded Deskstar 7K80 Hard Disk Drive Specification 88 The device provides information on these reported errors. 10.6.7 Error log Logging of error log information via the ...
... self-test log sector as described in the SMART self-test log data structure. Disabling SMART disables the delivering of reported errors is supported. If a device receives a firmware modification, all self-test log data is interrupted by SMART Execute Off-line Immediate command. The...self-test features which are updated accordingly during the self-tests, the device services the host command. If it is discarded Deskstar 7K80 Hard Disk Drive Specification 88 The device provides information on these reported errors. 10.6.7 Error log Logging of error log information via the ...
Specifications
Page 93
... Disable Password ('F1'h) ('F2'h) ('F3'h) ('F4'h) ('F5'h) ('F6'h) 10.7.1 Security mode The following security levels are supported for this mode is entered after power on , otherwise it is not set /change password. Deskstar 7K80 Hard Disk Drive Specification 89 When the device lock function is enabled and the User Password is then erased. 10...
... Disable Password ('F1'h) ('F2'h) ('F3'h) ('F4'h) ('F5'h) ('F6'h) 10.7.1 Security mode The following security levels are supported for this mode is entered after power on , otherwise it is not set /change password. Deskstar 7K80 Hard Disk Drive Specification 89 When the device lock function is enabled and the User Password is then erased. 10...
Specifications
Page 101
...Security Mode Feature set Max Unlock) until the next power cycle. Deskstar 7K80 Hard Disk Drive Specification 97 Make entire device accessible, including the protected area, by the following steps. Conventional usage without system software support Since the drive works as 12,692,735 (C1ACFFh) via the Set Max ADDRESS.... iv. Returned value shows that this command is accepted, the device is accessed by setting device maximum LBA as a 6.2 GB device, there is in the Set_Max_Locked mode. Read information data from the Set_Max_Locked mode to get the real device maximum LBA.
...Security Mode Feature set Max Unlock) until the next power cycle. Deskstar 7K80 Hard Disk Drive Specification 97 Make entire device accessible, including the protected area, by the following steps. Conventional usage without system software support Since the drive works as 12,692,735 (C1ACFFh) via the Set Max ADDRESS.... iv. Returned value shows that this command is accepted, the device is accessed by setting device maximum LBA as a 6.2 GB device, there is in the Set_Max_Locked mode. Read information data from the Set_Max_Locked mode to get the real device maximum LBA.
Specifications
Page 106
... Standby mode should be entered to the maximum performance level of FEh. Automatic Acoustic Management is supported if set and times out 2. The advanced power management levels contain discrete bands described in detail. Deskstar 7K80 Hard Disk Drive Specification 102 The device shall enter Standby mode if any of SET FEATURES command in the...
... Standby mode should be entered to the maximum performance level of FEh. Automatic Acoustic Management is supported if set and times out 2. The advanced power management levels contain discrete bands described in detail. Deskstar 7K80 Hard Disk Drive Specification 102 The device shall enter Standby mode if any of SET FEATURES command in the...
Specifications
Page 107
... the associated algorithm indicates that Automatic Acoustic Management is supported if set. Word 86, bit 9 indicates that the Standby mode should be entered to disable Automatic Acoustic Management Advanced Power Management, Automatic Acoustic Management, and the Standby timer setting are true: 1. Deskstar 7K80 Hard Disk Drive Specification 103 A SET FEATURES subcommand to select an...
... the associated algorithm indicates that Automatic Acoustic Management is supported if set. Word 86, bit 9 indicates that the Standby mode should be entered to disable Automatic Acoustic Management Advanced Power Management, Automatic Acoustic Management, and the Standby timer setting are true: 1. Deskstar 7K80 Hard Disk Drive Specification 103 A SET FEATURES subcommand to select an...
Specifications
Page 109
10.15.2 Identify Device Data Identify Device data, word 83, bit 7 indicates the device supports the Address Offset Feature. Identify Device data, word 86, bit 7 indicates the device is in Address Offset mode. 10.15.3 Exceptions in Address Offset Mode ... operation include the original native maximum LBA, Read Look Ahead operation is not carried out, even if it is removed by the Set Feature command. Deskstar 7K80 Hard Disk Drive Specification 105
10.15.2 Identify Device Data Identify Device data, word 83, bit 7 indicates the device supports the Address Offset Feature. Identify Device data, word 86, bit 7 indicates the device is in Address Offset mode. 10.15.3 Exceptions in Address Offset Mode ... operation include the original native maximum LBA, Read Look Ahead operation is not carried out, even if it is removed by the Set Feature command. Deskstar 7K80 Hard Disk Drive Specification 105
Specifications
Page 110
...,976,710,655 sectors. In addition, the number of commands: • Configure Stream • Read Stream PIO • Write Stream PIO Deskstar 7K80 Hard Disk Drive Specification 106 The host may read . A write to any Command Block register shall cause the device to clear the HOB bit to zero in...register. When the 48-bit Address feature set is implemented, the native maximum address is indicated in Identify Device response words 100 through 103. Support of 268,435,455. 10.17 Streaming feature Set The Streaming feature set is read the "previous content" of the Features, the Sector Count...
...,976,710,655 sectors. In addition, the number of commands: • Configure Stream • Read Stream PIO • Write Stream PIO Deskstar 7K80 Hard Disk Drive Specification 106 The host may read . A write to any Command Block register shall cause the device to clear the HOB bit to zero in...register. When the 48-bit Address feature set is implemented, the native maximum address is indicated in Identify Device response words 100 through 103. Support of 268,435,455. 10.17 Streaming feature Set The Streaming feature set is read the "previous content" of the Features, the Sector Count...
Specifications
Page 111
...sectors per command, as the Read Stream and Write Stream command execution time limits are defined to the media before posting command completion. Deskstar 7K80 Hard Disk Drive Specification 107 The operation is indicated in order to enable/disable caching shall not affect caching for each read and write operation with a... PIO versions of these commands limit the transfer rate (16.6 MB/s), provide no CRC protection, and limit status reporting as compared to support the streaming requirements of the AV content. • Read Stream DMA • Write Stream DMA • Read Log Ext...
...sectors per command, as the Read Stream and Write Stream command execution time limits are defined to the media before posting command completion. Deskstar 7K80 Hard Disk Drive Specification 107 The operation is indicated in order to enable/disable caching shall not affect caching for each read and write operation with a... PIO versions of these commands limit the transfer rate (16.6 MB/s), provide no CRC protection, and limit status reporting as compared to support the streaming requirements of the AV content. • Read Stream DMA • Write Stream DMA • Read Log Ext...
Specifications
Page 119
...0 50 0 1 0 1 0 0 0 0 EC 1 1 1 0 1 1 0 0 E3 1 1 1 0 0 0 1 1 97 1 0 0 1 0 1 1 1 E1 1 1 1 0 0 0 0 1 95 1 0 0 1 0 1 0 1 91 1 0 0 1 0 0 0 1 E4 1 1 1 0 0 1 0 0 C8 1 1 0 0 1 0 0 0 C9 1 1 0 0 1 0 0 1 25 0 0 1 0 0 1 0 1 22 0 0 1 0 0 0 1 0 23 0 0 1 0 0 0 1 1 2F 0 0 1 0 1 1 1 1 C4 1 1 0 0 0 1 0 0 29 0 0 1 0 1 0 0 1 F8 1 1 1 1 1 0 0 0 27 0 0 1 0 0 1 1 1 Deskstar 7K80 Hard Disk Drive Specification 115 tic 3 Flush Cache 3 Flush Cache Ext 2 Format Track 1 Identify Device 3 Idle 3 Idle* 3 Idle Immediate 3 Idle Immediate* 3 Initialize Device Param... the subcommands that are supported by the device.
...0 50 0 1 0 1 0 0 0 0 EC 1 1 1 0 1 1 0 0 E3 1 1 1 0 0 0 1 1 97 1 0 0 1 0 1 1 1 E1 1 1 1 0 0 0 0 1 95 1 0 0 1 0 1 0 1 91 1 0 0 1 0 0 0 1 E4 1 1 1 0 0 1 0 0 C8 1 1 0 0 1 0 0 0 C9 1 1 0 0 1 0 0 1 25 0 0 1 0 0 1 0 1 22 0 0 1 0 0 0 1 0 23 0 0 1 0 0 0 1 1 2F 0 0 1 0 1 1 1 1 C4 1 1 0 0 0 1 0 0 29 0 0 1 0 1 0 0 1 F8 1 1 1 1 1 0 0 0 27 0 0 1 0 0 1 1 1 Deskstar 7K80 Hard Disk Drive Specification 115 tic 3 Flush Cache 3 Flush Cache Ext 2 Format Track 1 Identify Device 3 Idle 3 Idle* 3 Idle Immediate 3 Idle Immediate* 3 Initialize Device Param... the subcommands that are supported by the device.
Specifications
Page 128
...no longer support the indicated command, mode, or feature set of error information is described in Table 78: "DCO error information definition" on changing these words are violated or any of the Device Configuration Overlay data structure is now enabled Deskstar 7K80 Hard Disk Drive Specification 124... manufacturer to an IDENTIFY DEVICE or IDENTIFY PACKET DEVICE command will reflect the reduced set . If a bit is set of supporting. The Definition of capabilities, while the DEVICE CONFIGURATION IDENTIFY command will abort that command and returns error reason code as indicated ...
...no longer support the indicated command, mode, or feature set of error information is described in Table 78: "DCO error information definition" on changing these words are violated or any of the Device Configuration Overlay data structure is now enabled Deskstar 7K80 Hard Disk Drive Specification 124... manufacturer to an IDENTIFY DEVICE or IDENTIFY PACKET DEVICE command will reflect the reduced set . If a bit is set of supporting. The Definition of capabilities, while the DEVICE CONFIGURATION IDENTIFY command will abort that command and returns error reason code as indicated ...
Specifications
Page 129
... the data structure checksum. Deskstar 7K80 Hard Disk Drive Specification 125 Table 77: Device Configuration Overlay Data structure Word 0 1 2 3-6 7 8-254 255 Content 0001h Data Structure revision Multiword DMA modes supported 15-3 Reserved 2 1 = Multiword DMA mode 2 and below are supported 1 1 = Multiword DMA mode 1 and below are supported 0 1 = Multiword DMA mode 0 is supported Ultra DMA modes supported 15-6 Reserved 5 1 = Ultra...
... the data structure checksum. Deskstar 7K80 Hard Disk Drive Specification 125 Table 77: Device Configuration Overlay Data structure Word 0 1 2 3-6 7 8-254 255 Content 0001h Data Structure revision Multiword DMA modes supported 15-3 Reserved 2 1 = Multiword DMA mode 2 and below are supported 1 1 = Multiword DMA mode 1 and below are supported 0 1 = Multiword DMA mode 0 is supported Ultra DMA modes supported 15-6 Reserved 5 1 = Ultra...
Specifications
Page 130
... feature set is supported 8 1 = 48-bit Addressing feature set supported 7 1 = Host Protected Area feature set supported 6 1 = Automatic acoustic management supported 5 1 = Read/Write DMA Queued commands supported 4 1 = Power-up in Standby feature set supported 3 1 = Security feature set supported 2 1 = SMART error log supported 1 1 = SMART self-test supported 0 1 = SMART feature set supported Reserved Integrity word 15-8 Checksum 7-0 Signature (A5h) Deskstar 7K80 Hard Disk Drive Specification 126
... feature set is supported 8 1 = 48-bit Addressing feature set supported 7 1 = Host Protected Area feature set supported 6 1 = Automatic acoustic management supported 5 1 = Read/Write DMA Queued commands supported 4 1 = Power-up in Standby feature set supported 3 1 = Security feature set supported 2 1 = SMART error log supported 1 1 = SMART self-test supported 0 1 = SMART feature set supported Reserved Integrity word 15-8 Checksum 7-0 Signature (A5h) Deskstar 7K80 Hard Disk Drive Specification 126
Specifications
Page 131
...0 0 0 0 1 1 1 Sector Count Sector_Count(0007) Sector Number Sector_Count(0815) Cylinder Low Cylinder High Device/Head - - - Only support 07h which indicates that save downloaded code for this Download command, UNC error will be transferred. The Sector Number register is vendor specific. A value...0 Status Register 7 654 3 2 1 0 BSY RDY DF DSC DRQ COR IDX ERR 0 101 0 0 - Thus the Deskstar 7K80 Hard Disk Drive Specification 127 V Output Parameters To The Device Feature Sector Count Sector Number Subcommand code. The size of the data transfer is determined ...
...0 0 0 0 1 1 1 Sector Count Sector_Count(0007) Sector Number Sector_Count(0815) Cylinder Low Cylinder High Device/Head - - - Only support 07h which indicates that save downloaded code for this Download command, UNC error will be transferred. The Sector Number register is vendor specific. A value...0 Status Register 7 654 3 2 1 0 BSY RDY DF DSC DRQ COR IDX ERR 0 101 0 0 - Thus the Deskstar 7K80 Hard Disk Drive Specification 127 V Output Parameters To The Device Feature Sector Count Sector Number Subcommand code. The size of the data transfer is determined ...
Specifications
Page 141
... PIO Transfer Modes Supported 15-8(=0) Reserved 7-0 (=3) Advanced PIO Transfer Modes Supported '11' = PIO Mode 3 and 4 Supported Minimum Multiword DMA Transfer Cycle Time Per Word 15-0(=78) Cycle time in sectors Word 57 specifies the low word of current sectors per track Current capacity in nanoseconds (120ns, 16.6MB/s) Deskstar 7K80 Hard Disk Drive Specification 137 Table...
... PIO Transfer Modes Supported 15-8(=0) Reserved 7-0 (=3) Advanced PIO Transfer Modes Supported '11' = PIO Mode 3 and 4 Supported Minimum Multiword DMA Transfer Cycle Time Per Word 15-0(=78) Cycle time in sectors Word 57 specifies the low word of current sectors per track Current capacity in nanoseconds (120ns, 16.6MB/s) Deskstar 7K80 Hard Disk Drive Specification 137 Table...
Specifications
Page 142
...(Part 3 of 7) Word 66 67 68 69-74 75 76-79 80 81 82 Content 0078H 00F0H 0078H 0000H 00xxH 0000H 00FCH 001AH 74EBH Description ...ATA/ATAPI-5 and ATA/ATAPI-6 and ATA/ATAPI-7 Minor version number 15-0(=1Ah) ATA/ATAPI-7 T13 1532D revision 1 Command set supported 15 (=0) Reserved 14 (=1) NOP command 13 (=1) READ BUFFER command 12 (=1) WRITE BUFFER command 11 (=0) Reserved 10 (=1) Host Protected...PACKET Command feature set 3 (=1) Power management feature set 2 (=0) Removable feature set 1 (=1) Security feature set 0 (=1) SMART feature Set Deskstar 7K80 Hard Disk Drive Specification 138
...(Part 3 of 7) Word 66 67 68 69-74 75 76-79 80 81 82 Content 0078H 00F0H 0078H 0000H 00xxH 0000H 00FCH 001AH 74EBH Description ...ATA/ATAPI-5 and ATA/ATAPI-6 and ATA/ATAPI-7 Minor version number 15-0(=1Ah) ATA/ATAPI-7 T13 1532D revision 1 Command set supported 15 (=0) Reserved 14 (=1) NOP command 13 (=1) READ BUFFER command 12 (=1) WRITE BUFFER command 11 (=0) Reserved 10 (=1) Host Protected...PACKET Command feature set 3 (=1) Power management feature set 2 (=0) Removable feature set 1 (=1) Security feature set 0 (=1) SMART feature Set Deskstar 7K80 Hard Disk Drive Specification 138
Specifications
Page 143
... Max Security extension 7 (=1) 6 (=1) 5 (=1) Set Features Address Offset feature mode SET FEATURES subcommand required to spin-up after power-up Power-Up In Standby feature set supported 4 (=0) Removable Media Status Notification feature 3 (=1) Advanced Power Management feature set 2 (=0) CFA feature set 1 (=0) READ/WRITE DMA QUEUED 0 (=1) DOWNLOAD MICROCODE command 84... 6 LOOK AHEAD 5 WRITE CACHE 4 PACKET Command feature set 3 Power management feature set 2 Removable media feature set 1 Security feature set 0 SMART feature set Deskstar 7K80 Hard Disk Drive Specification 139
... Max Security extension 7 (=1) 6 (=1) 5 (=1) Set Features Address Offset feature mode SET FEATURES subcommand required to spin-up after power-up Power-Up In Standby feature set supported 4 (=0) Removable Media Status Notification feature 3 (=1) Advanced Power Management feature set 2 (=0) CFA feature set 1 (=0) READ/WRITE DMA QUEUED 0 (=1) DOWNLOAD MICROCODE command 84... 6 LOOK AHEAD 5 WRITE CACHE 4 PACKET Command feature set 3 Power management feature set 2 Removable media feature set 1 Security feature set 0 SMART feature set Deskstar 7K80 Hard Disk Drive Specification 139