Maintenance and Service Guide
Page 41
... system. Service Manual Removal and Replacement 2-11 When the HP logo appears, press esc to the notebook. 2. Use the arrow keys to restore only the C... partition. 7. select Advanced and then select to select the CD/DVD drive as the first boot device, and then press enter. 6. When the operating system has been installed and while Windows...not to recover the notebook's original operating system and drivers. If the notebook is not enabled, select Start > Run. Turn on -screen instructions for installing the drivers. 10. If prompted...
... system. Service Manual Removal and Replacement 2-11 When the HP logo appears, press esc to the notebook. 2. Use the arrow keys to restore only the C... partition. 7. select Advanced and then select to select the CD/DVD drive as the first boot device, and then press enter. 6. When the operating system has been installed and while Windows...not to recover the notebook's original operating system and drivers. If the notebook is not enabled, select Start > Run. Turn on -screen instructions for installing the drivers. 10. If prompted...
Maintenance and Service Guide
Page 103
... drivers), uninstall that software. Blinking cursor appears while system is turned on and warmed up. Repair Center: Likely Causes Make sure notebook is loading and checking hardware and network connections. Try external monitor. Make sure SDRAM modules are not set to Never. Notebook can... take a minute or longer to resume if network card is enabled in Power in Control Panel. Make sure hibernate support is installed. Make sure CPU module is reinitialized, Windows desktop appears. When hardware is installed...
... drivers), uninstall that software. Blinking cursor appears while system is turned on and warmed up. Repair Center: Likely Causes Make sure notebook is loading and checking hardware and network connections. Try external monitor. Make sure SDRAM modules are not set to Never. Notebook can... take a minute or longer to resume if network card is enabled in Power in Control Panel. Make sure hibernate support is installed. Make sure CPU module is reinitialized, Windows desktop appears. When hardware is installed...
Maintenance and Service Guide
Page 107
... pad is disabled if external PS/2 mouse is connected. Use only DDR-266 SDRAM modules. Check for use with notebook. Make sure touch pad is enabled in Windows Help. Use memory troubleshooter in Mouse Properties. SDRAM module SDRAM module Increase sound volume. Check software controls. Make sure... Motherboard Repair Center: Comments Check operation using headphones or external speakers (switchboard PCA). Check whether sound is installed from \hp\drivers\TouchPad.) Top case Motherboard Top case Motherboard Top case Motherboard Make sure C drive has adequate free space.
... pad is disabled if external PS/2 mouse is connected. Use only DDR-266 SDRAM modules. Check for use with notebook. Make sure touch pad is enabled in Windows Help. Use memory troubleshooter in Mouse Properties. SDRAM module SDRAM module Increase sound volume. Check software controls. Make sure... Motherboard Repair Center: Comments Check operation using headphones or external speakers (switchboard PCA). Check whether sound is installed from \hp\drivers\TouchPad.) Top case Motherboard Top case Motherboard Top case Motherboard Make sure C drive has adequate free space.
Maintenance and Service Guide
Page 108
...: contact device vendor and HP Notebook Web site (see page vii) for data line. Open hardware Device Manager. In a hotel, ask for latest USB drivers. Check port settings in Control Panel. Motherboard Check settings in Device Manager. If modem has a conflict, try the other port. Check settings in Windows Help. Test ports with e-Diagtools...
...: contact device vendor and HP Notebook Web site (see page vii) for data line. Open hardware Device Manager. In a hotel, ask for latest USB drivers. Check port settings in Control Panel. Motherboard Check settings in Device Manager. If modem has a conflict, try the other port. Check settings in Windows Help. Test ports with e-Diagtools...
Maintenance and Service Guide
Page 109
...LAN cable may not be down. Try to network or network may be connected to enable the infrared port. Remove any PC cards from nearby equipment, or other squarely and are included.) Make sure line between infrared ports is 100 meters (330 feet.... Sunlight, heat from notebook (possible IRQ conflict). Symptom LAN/network General problems Infrared General problems Call Center: Suggestions Repair Center: Likely Causes Check cables and connections. Check settings in Windows Help. Motherboard Infrared is disabled and no drivers installed as shipped. (Drivers are no more than ...
...LAN cable may not be down. Try to network or network may be connected to enable the infrared port. Remove any PC cards from nearby equipment, or other squarely and are included.) Make sure line between infrared ports is 100 meters (330 feet.... Sunlight, heat from notebook (possible IRQ conflict). Symptom LAN/network General problems Infrared General problems Call Center: Suggestions Repair Center: Likely Causes Check cables and connections. Check settings in Windows Help. Motherboard Infrared is disabled and no drivers installed as shipped. (Drivers are no more than ...
Maintenance and Service Guide
Page 112
... and repairing the notebook: • Notebook e-Diagtools diagnostic program (below) • Power-on self-test (page 3-20) • Sycard PCCtest 450 PC card (page 3-26) • Windows Management Instrumentation (page...so drivers can download the latest version of e-Diagtools. 1. Diagnostic Tools This section describes the following procedure describes how to run e-Diagtools. The notebook reboots ... 8. When the HP logo appears, press F10 to preserve the state of detected hardware. 5. When the Configuration Description appears, check the list of the notebook. Press F2 to...
... and repairing the notebook: • Notebook e-Diagtools diagnostic program (below) • Power-on self-test (page 3-20) • Sycard PCCtest 450 PC card (page 3-26) • Windows Management Instrumentation (page...so drivers can download the latest version of e-Diagtools. 1. Diagnostic Tools This section describes the following procedure describes how to run e-Diagtools. The notebook reboots ... 8. When the HP logo appears, press F10 to preserve the state of detected hardware. 5. When the Configuration Description appears, check the list of the notebook. Press F2 to...
Hard Drive White Paper
Page 5
... Standby mode before transporting it will be unused for information: - Windows XP command line: http://support.microsoft.com/default.aspx?scid=kb;EN-US;283080 - Please refer to the hard drive. HP Recommendations for Notebook Users • Install HP Notebook LidSwitch Policy, or as given in the "F10 Setup Hard Drive.... As a result, movement of the hard drive reading/writing heads is moved to removable media. • Regularly check the HP Web site for system BIOS and driver enhancements. 5 Windows XP: http://support.microsoft.com/default.aspx?scid=kb;en-us;314058&Product=winxp -
... Standby mode before transporting it will be unused for information: - Windows XP command line: http://support.microsoft.com/default.aspx?scid=kb;EN-US;283080 - Please refer to the hard drive. HP Recommendations for Notebook Users • Install HP Notebook LidSwitch Policy, or as given in the "F10 Setup Hard Drive.... As a result, movement of the hard drive reading/writing heads is moved to removable media. • Regularly check the HP Web site for system BIOS and driver enhancements. 5 Windows XP: http://support.microsoft.com/default.aspx?scid=kb;en-us;314058&Product=winxp -