Use and Care Manual
Page 1
Bottom Freezer Refrigerators ge.com Safety Instructions 2, 3 Operating Instructions Automatic Icemaker 10 Care and Cleaning 11, 12 Controls 4 Crispers and Pans 7 Freezer 8, 9 Replacing the Light Bulbs 13 Shelves and Bins 6 Water Filter 5 Installation Instructions Installing the Refrigerator 15-19 Installing the Water Line 28-30 Preparing to Install the Refrigerator... 14 Removing and Replacing the Doors (Double Door Refrigerator Models only 25-27 Removing and Replacing the Freezer Drawer 20, 21 Reversing the Door Swing (Single Door Refrigerator Models only 22...
Bottom Freezer Refrigerators ge.com Safety Instructions 2, 3 Operating Instructions Automatic Icemaker 10 Care and Cleaning 11, 12 Controls 4 Crispers and Pans 7 Freezer 8, 9 Replacing the Light Bulbs 13 Shelves and Bins 6 Water Filter 5 Installation Instructions Installing the Refrigerator 15-19 Installing the Water Line 28-30 Preparing to Install the Refrigerator... 14 Removing and Replacing the Doors (Double Door Refrigerator Models only 25-27 Removing and Replacing the Freezer Drawer 20, 21 Reversing the Door Swing (Single Door Refrigerator Models only 22...
Use and Care Manual
Page 4
... you have set. Adjust the controls one increment at 5. Allow 24 hours for the refrigerator control knob stops cooling in both the refrigerator and freezer compartments, but does not shut off electrical power to stabilize. If this film was not... for digital and 0 for the temperature to the refrigerator. 4 Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions Installation Instructions About the controls with temperature settings. (on some models) (on some models) NOTE: The refrigerator is shipped with protective film covering the digital temperature...
... you have set. Adjust the controls one increment at 5. Allow 24 hours for the refrigerator control knob stops cooling in both the refrigerator and freezer compartments, but does not shut off electrical power to stabilize. If this film was not... for digital and 0 for the temperature to the refrigerator. 4 Consumer Support Troubleshooting Tips Operating Instructions Safety Instructions Installation Instructions About the controls with temperature settings. (on some models) (on some models) NOTE: The refrigerator is shipped with protective film covering the digital temperature...
Use and Care Manual
Page 5
...refrigerator compartment. When the cartridge is properly installed, you are replacing the cartridge, first remove the old one. Do not overtighten. A small amount of water may be positioned vertically. CAUTION: If air has been trapped in the system, the filter cartridge may drip down . Filter Model... Filters: To order additional filter cartridges in the back upper right corner of the cartridge. Lining up the arrow on some models) ge.com Water Filter Cartridge The water filter cartridge is not available. When to Replace the Filter The filter cartridge should consult the...
...refrigerator compartment. When the cartridge is properly installed, you are replacing the cartridge, first remove the old one. Do not overtighten. A small amount of water may be positioned vertically. CAUTION: If air has been trapped in the system, the filter cartridge may drip down . Filter Model... Filters: To order additional filter cartridges in the back upper right corner of the cartridge. Lining up the arrow on some models) ge.com Water Filter Cartridge The water filter cartridge is not available. When to Replace the Filter The filter cartridge should consult the...
Use and Care Manual
Page 6
... manner. Non-Adjustable Shelves on the Door (on all items from the shelf. It will lock in the molded supports on the track. Refrigerator Compartment To remove: Remove all models. To replace: Engage the shelf in place. Operating Instructions Safety Instructions About the shelves and bins. Lift the shelf up at the... out. Installation Instructions Consumer Support Troubleshooting Tips 6 then pull out. To replace: While tilting the shelf up ; Lower the front of the shelf until the bottom of the shelf in a slot on the door and push down. Tilt the shelf up at the front.
... manner. Non-Adjustable Shelves on the Door (on all items from the shelf. It will lock in the molded supports on the track. Refrigerator Compartment To remove: Remove all models. To replace: Engage the shelf in place. Operating Instructions Safety Instructions About the shelves and bins. Lift the shelf up at the... out. Installation Instructions Consumer Support Troubleshooting Tips 6 then pull out. To replace: While tilting the shelf up ; Lower the front of the shelf until the bottom of the shelf in a slot on the door and push down. Tilt the shelf up at the front.
Use and Care Manual
Page 10
...Always be joined together. approximately 100-130 cubes in the O (off) position. When the refrigerator has been connected to the water supply, set the power switch in a 24-hour period, depending on freezer compartment temperature, room temperature, number of the feeler arm. You will fill with the sweep ... icemaker. (on some models) A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes. Throw away the first few batches of the feeler arm, the icemaker will turn green when the freezer light switch is pressed in or when the freezer door is shut off...
...Always be joined together. approximately 100-130 cubes in the O (off) position. When the refrigerator has been connected to the water supply, set the power switch in a 24-hour period, depending on freezer compartment temperature, room temperature, number of the feeler arm. You will fill with the sweep ... icemaker. (on some models) A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes. Throw away the first few batches of the feeler arm, the icemaker will turn green when the freezer light switch is pressed in or when the freezer door is shut off...
Use and Care Manual
Page 11
...Keep the outside clean. After cleaning the door gaskets, apply a thin layer of the refrigerator. ge.com Cleaning the Outside The door handles and trim. Use an appliance wax polish on some models) can erode the paint. Bumping tempered glass can scratch and weaken the paint finish.... Do not use appliance wax or polish on the door handles and trim. A spray-on stainless steel cleaner works best. Do not wash any plastic refrigerator parts in the refrigerator and freezer ...
...Keep the outside clean. After cleaning the door gaskets, apply a thin layer of the refrigerator. ge.com Cleaning the Outside The door handles and trim. Use an appliance wax polish on some models) can erode the paint. Bumping tempered glass can scratch and weaken the paint finish.... Do not use appliance wax or polish on the door handles and trim. A spray-on stainless steel cleaner works best. Do not wash any plastic refrigerator parts in the refrigerator and freezer ...
Use and Care Manual
Page 12
...at the bottom front of the refrigerator. Clean the interior with embossed surfaces. Lower the leveling legs until they touch the floor. Set the icemaker power switch to the O (off) position and shut off the water supply to the floor covering or refrigerator. Handle ...cord or icemaker supply line (on some models). Preparing for Vacation For long vacations or absences, remove food and unplug the refrigerator. Leave the doors open. This could damage the refrigerator. All types of the refrigerator. Pull the refrigerator straight out and return it straight in ...
...at the bottom front of the refrigerator. Clean the interior with embossed surfaces. Lower the leveling legs until they touch the floor. Set the icemaker power switch to the O (off) position and shut off the water supply to the floor covering or refrigerator. Handle ...cord or icemaker supply line (on some models). Preparing for Vacation For long vacations or absences, remove food and unplug the refrigerator. Leave the doors open. This could damage the refrigerator. All types of the refrigerator. Pull the refrigerator straight out and return it straight in ...
Use and Care Manual
Page 14
Installation Instructions Refrigerator Models 20 and 22 Questions? Installation of the installer. • Product failure due to improper installation is not covered under the Warranty. Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com In Canada, call 1.800.561.3344 or Visit our...Level WATER SUPPLY TO THE ICEMAKER AND DISPENSER (ON SOME MODELS) If the refrigerator has an icemaker, it will not fit through a doorway, the refrigerator door and freezer drawer can be connected to be removed. • To remove the refrigerator door, see Step 1 in Canada at : www....
Installation Instructions Refrigerator Models 20 and 22 Questions? Installation of the installer. • Product failure due to improper installation is not covered under the Warranty. Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com In Canada, call 1.800.561.3344 or Visit our...Level WATER SUPPLY TO THE ICEMAKER AND DISPENSER (ON SOME MODELS) If the refrigerator has an icemaker, it will not fit through a doorway, the refrigerator door and freezer drawer can be connected to be removed. • To remove the refrigerator door, see Step 1 in Canada at : www....
Use and Care Manual
Page 15
... plumbing and electrical connections. If using GE SmartConnect™ Refrigerator Tubing Kit, you will need an additional tube (WX08X10002) to connect the filter. Do not cut plastic tube to provide one if your refrigerator does not have a water filter, ...hand truck to move and complete this refrigerator. Place the refrigerator on some models) •IMPORTANT NOTE: This refrigerator is not a cold water supply, you will need to install filter. Reinstall top hinge(s). G Reinstall the bottom freezer drawer or door. Standard Depth Models Sides 1/8″ (3 mm) Top...
... plumbing and electrical connections. If using GE SmartConnect™ Refrigerator Tubing Kit, you will need an additional tube (WX08X10002) to connect the filter. Do not cut plastic tube to provide one if your refrigerator does not have a water filter, ...hand truck to move and complete this refrigerator. Place the refrigerator on some models) •IMPORTANT NOTE: This refrigerator is not a cold water supply, you will need to install filter. Reinstall top hinge(s). G Reinstall the bottom freezer drawer or door. Standard Depth Models Sides 1/8″ (3 mm) Top...
Use and Care Manual
Page 16
...easily when opened about halfway. Tubing Clamp 1/4″ Tubing 16 Installation Instructions INSTALLING THE REFRIGERATOR (cont.) 1 CONNECTING THE REFRIGERATOR TO THE HOUSE WATER LINE (cont.) A If you are using the GE SmartConnect™ tubing, the nuts are already assembled to the tubing. If you are... using copper tubing, insert the end of the tubing into the refrigerator connection, at the shutoff valve (house water supply) and check for any leaks. 3 PLUG IN THE REFRIGERATOR On models ...
...easily when opened about halfway. Tubing Clamp 1/4″ Tubing 16 Installation Instructions INSTALLING THE REFRIGERATOR (cont.) 1 CONNECTING THE REFRIGERATOR TO THE HOUSE WATER LINE (cont.) A If you are using the GE SmartConnect™ tubing, the nuts are already assembled to the tubing. If you are... using copper tubing, insert the end of the tubing into the refrigerator connection, at the shutoff valve (house water supply) and check for any leaks. 3 PLUG IN THE REFRIGERATOR On models ...
Use and Care Manual
Page 18
... may vary) 9 ATTACH THE FREEZER DOOR HANDLE Stainless steel and plastic handles: A Attach the handle firmly to the mounting fasteners and tighten the set screws with the handle mounting fasteners. Installation Instructions INSTALLING THE REFRIGERATOR (cont.) 8 ATTACH THE FRESH... FOOD DOOR HANDLE Stainless steel handle: A Attach the handle to the handle mounting fasteners and tighten the set screws on the opposite door. A Mounting Fasteners (appearance may vary) 18 NOTE: For Double Door models follow the same procedure on the bottom...
... may vary) 9 ATTACH THE FREEZER DOOR HANDLE Stainless steel and plastic handles: A Attach the handle firmly to the mounting fasteners and tighten the set screws with the handle mounting fasteners. Installation Instructions INSTALLING THE REFRIGERATOR (cont.) 8 ATTACH THE FRESH... FOOD DOOR HANDLE Stainless steel handle: A Attach the handle to the handle mounting fasteners and tighten the set screws on the opposite door. A Mounting Fasteners (appearance may vary) 18 NOTE: For Double Door models follow the same procedure on the bottom...
Use and Care Manual
Page 19
... PACKAGING, START ICEMAKER (icemaker models) A) Remove all tape, foam and protective packing from shelves and drawers. B) Remove the tie downs from tipping. It will then begin to operate until it . The leveling legs also prevent the refrigerator from the freezer baskets. C Replace the base... grille by removing the two Phillips head screws. 11 SET THE CONTROLS Set the controls to the recommended setting. B Turn the leveling legs clockwise to raise the refrigerator, counterclockwise to lower it...
... PACKAGING, START ICEMAKER (icemaker models) A) Remove all tape, foam and protective packing from shelves and drawers. B) Remove the tie downs from tipping. It will then begin to operate until it . The leveling legs also prevent the refrigerator from the freezer baskets. C Replace the base... grille by removing the two Phillips head screws. 11 SET THE CONTROLS Set the controls to the recommended setting. B Turn the leveling legs clockwise to raise the refrigerator, counterclockwise to lower it...
Use and Care Manual
Page 20
... grille by removing the screws. Screw 20 B The freezer basket rests on a non-scratching surface. C Set the drawer front on a frame inside the freezer drawer. Read these instructions completely and carefully. 1 REMOVE THE BASKET A Open the freezer drawer until it stops. C Lift the.... Lift the basket up on both sides of the railing. Installation Instructions REMOVING THE FREEZER DRAWER (on some models) The freezer drawer can be removed, if needed ) If, after removing the freezer drawer and refrigerator door, the refrigerator will still not fit through tight areas.
... grille by removing the screws. Screw 20 B The freezer basket rests on a non-scratching surface. C Set the drawer front on a frame inside the freezer drawer. Read these instructions completely and carefully. 1 REMOVE THE BASKET A Open the freezer drawer until it stops. C Lift the.... Lift the basket up on both sides of the railing. Installation Instructions REMOVING THE FREEZER DRAWER (on some models) The freezer drawer can be removed, if needed ) If, after removing the freezer drawer and refrigerator door, the refrigerator will still not fit through tight areas.
Use and Care Manual
Page 22
...a non-scratching work surface for changing the hinges from inside up to the door by carefully prying it up with masking tape. Phillips Screwdriver Torx T-20 Driver F Set the door on a non-scratching surface with the inside the socket. NOTE: A replacement logo badge is completed. C Using a ...• Set screws down by their related parts to avoid using them in the bottom of the door. Then lift the hinge straight up . 22 Installation Instructions REVERSING THE DOOR SWING (Single Door Refrigerator Models only) IMPORTANT NOTES When reversing the door swing: NOTE: Door swing is not...
...a non-scratching work surface for changing the hinges from inside up to the door by carefully prying it up with masking tape. Phillips Screwdriver Torx T-20 Driver F Set the door on a non-scratching surface with the inside the socket. NOTE: A replacement logo badge is completed. C Using a ...• Set screws down by their related parts to avoid using them in the bottom of the door. Then lift the hinge straight up . 22 Installation Instructions REVERSING THE DOOR SWING (Single Door Refrigerator Models only) IMPORTANT NOTES When reversing the door swing: NOTE: Door swing is not...
Use and Care Manual
Page 25
... Once you begin, do not move the cabinet. REMOVING THE DOORS (Double Door Refrigerator Models only) IMPORTANT NOTES NOTE: Door swing is on the center hinge pin or inside door hinge pin hole located in the bottom of the badge with the holes in place, tighten the top hinge bolts. TOOLS ... side and make sure the door is straight and the gap between the doors is aligned with the bolts. Installation Instructions 9 REHANG REFRIGERATOR DOOR A Lower the refrigerator door onto the center hinge pin. Ensure that the plastic hinge pin thimble is not reversible. • Read the instructions all door...
... Once you begin, do not move the cabinet. REMOVING THE DOORS (Double Door Refrigerator Models only) IMPORTANT NOTES NOTE: Door swing is on the center hinge pin or inside door hinge pin hole located in the bottom of the badge with the holes in place, tighten the top hinge bolts. TOOLS ... side and make sure the door is straight and the gap between the doors is aligned with the bolts. Installation Instructions 9 REHANG REFRIGERATOR DOOR A Lower the refrigerator door onto the center hinge pin. Ensure that the plastic hinge pin thimble is not reversible. • Read the instructions all door...
Use and Care Manual
Page 26
... Hinge Cover Top Hinge 3 REMOVE OPPOSITE DOOR Follow the same procedure on the opposite side. 4 REMOVE FREEZER DRAWER Refer to the side on top of the refrigerator. Ensure that the plastic hinge pin thimble remains on a non-scratching surface with the inside door hinge ... up . Installation Instructions REMOVING THE DOORS (Double Door Refrigerator Models only) 1 REMOVE THE REFRIGERATOR DOORS A Tape the doors shut with masking tape. 1 REMOVE THE REFRIGERATOR DOORS (cont.) E Remove the tape and tilt the door away from the socket in the bottom of the door. D Using a 5/16″ ...
... Hinge Cover Top Hinge 3 REMOVE OPPOSITE DOOR Follow the same procedure on the opposite side. 4 REMOVE FREEZER DRAWER Refer to the side on top of the refrigerator. Ensure that the plastic hinge pin thimble remains on a non-scratching surface with the inside door hinge ... up . Installation Instructions REMOVING THE DOORS (Double Door Refrigerator Models only) 1 REMOVE THE REFRIGERATOR DOORS A Tape the doors shut with masking tape. 1 REMOVE THE REFRIGERATOR DOORS (cont.) E Remove the tape and tilt the door away from the socket in the bottom of the door. D Using a 5/16″ ...
Use and Care Manual
Page 27
...legs to the top of the door. Use a 1/4″ Allen wrench to match the right door. Installation Instructions REPLACING THE DOORS (Double Door Refrigerator Models only) 1 INSTALL CENTER HINGE Install the center hinge on each side. 3 REPLACE OPPOSITE DOOR Follow the same procedure on the same side as ... in place, tighten the top hinge bolts. While holding the aligned door in the bottom of the cabinet loosely with the bolts. Make sure the door is not folded. Adjustable pin 5 REPLACE FREEZER DRAWER Refer to raise the lowest door by turning the leveling leg on the opposite ...
...legs to the top of the door. Use a 1/4″ Allen wrench to match the right door. Installation Instructions REPLACING THE DOORS (Double Door Refrigerator Models only) 1 INSTALL CENTER HINGE Install the center hinge on each side. 3 REPLACE OPPOSITE DOOR Follow the same procedure on the same side as ... in place, tighten the top hinge bolts. While holding the aligned door in the bottom of the cabinet loosely with the bolts. Make sure the door is not folded. Adjustable pin 5 REPLACE FREEZER DRAWER Refer to raise the lowest door by turning the leveling leg on the opposite ...
Use and Care Manual
Page 28
...installations must be in accordance with the RO filter can cause damage to refrigerator parts and lead to the refrigerator. Installation Instructions INSTALLING THE WATER LINE (ICEMAKER MODELS) BEFORE YOU BEGIN Recommended copper water supply kits are available in the... following lengths: 6′ (1.8 m) - Approved plastic water supply lines are cut square. Using the refrigerator's water filtration cartridge in conjunction with local plumbing code requirements. This water line installation is with a GE...
...installations must be in accordance with the RO filter can cause damage to refrigerator parts and lead to the refrigerator. Installation Instructions INSTALLING THE WATER LINE (ICEMAKER MODELS) BEFORE YOU BEGIN Recommended copper water supply kits are available in the... following lengths: 6′ (1.8 m) - Approved plastic water supply lines are cut square. Using the refrigerator's water filtration cartridge in conjunction with local plumbing code requirements. This water line installation is with a GE...
Use and Care Manual
Page 31
...food is first plugged in defrost cycle. Problem Refrigerator does not operate Vibration or rattling (slight vibration is unplugged. ge.com Newer refrigerators sound different from the evaporator and flows into...9632; On models with a dispenser, during water dispense, you may hear a whooshing sound when the doors close. This happens as ice melts from older refrigerators. Modern refrigerators have more...sounds, see the About the automatic icemaker section. Control in order to the refrigerator or freezer compartments. What To Do • Wait about 30 minutes for service. The...
...food is first plugged in defrost cycle. Problem Refrigerator does not operate Vibration or rattling (slight vibration is unplugged. ge.com Newer refrigerators sound different from the evaporator and flows into...9632; On models with a dispenser, during water dispense, you may hear a whooshing sound when the doors close. This happens as ice melts from older refrigerators. Modern refrigerators have more...sounds, see the About the automatic icemaker section. Control in order to the refrigerator or freezer compartments. What To Do • Wait about 30 minutes for service. The...
Use and Care Manual
Page 34
... realigning. • See Align Double Doors section located under Replacing the Door (Double Door Refrigerator Models only). compartment light up , check to open : remove some models) Handle is loose / handle has a gap Refrigerator beeping Control setting is not lit Refrigerator doors are burned out, and replace if necessary. Filter cartridge not properly installed. Readjust the... if at the top of the cartridge should be positioned vertically. Handle needs adjusting. • See Attach the Fresh Food Door Handle and Attach the Freezer Door Handle sections for service...
... realigning. • See Align Double Doors section located under Replacing the Door (Double Door Refrigerator Models only). compartment light up , check to open : remove some models) Handle is loose / handle has a gap Refrigerator beeping Control setting is not lit Refrigerator doors are burned out, and replace if necessary. Filter cartridge not properly installed. Readjust the... if at the top of the cartridge should be positioned vertically. Handle needs adjusting. • See Attach the Fresh Food Door Handle and Attach the Freezer Door Handle sections for service...