Installation Instructions (All Languages)
Page 9
... 4 in . (9.5cm) (2 cm) to installation depth. Upward or downward venting of water inlet hose on Steam Models adds 3/4 in . (10.2 cm) to installation depth. Downward venting of exhaust on pedestal-mounted dryer adds approximately 1.7 in. (4.3 cm) to installation depth. 13.50" (34.5cm) to center of rear ... (192.5cm) gas supply pipe on rear of gas unit 39.00" (99cm) electrical supply on rear of unit centerline height for rear vent 41.00" (104cm) * To obtain these minimal depth dimensions, dryer must either be vented straight back or with a quick-turn 90° elbow. Upward...
... 4 in . (9.5cm) (2 cm) to installation depth. Upward or downward venting of water inlet hose on Steam Models adds 3/4 in . (10.2 cm) to installation depth. Downward venting of exhaust on pedestal-mounted dryer adds approximately 1.7 in. (4.3 cm) to installation depth. 13.50" (34.5cm) to center of rear ... (192.5cm) gas supply pipe on rear of gas unit 39.00" (99cm) electrical supply on rear of unit centerline height for rear vent 41.00" (104cm) * To obtain these minimal depth dimensions, dryer must either be vented straight back or with a quick-turn 90° elbow. Upward...
Installation Instructions (All Languages)
Page 15
The faucet MUST be between 30 and 120 psi. Your water department can advise you of your dryer's water inlet. Turn off COLD water supply to clear any contaminants in the line. 4. RUBBER WASHER MUST BE PRESENT AND UNDAMAGED COLD INLET HOSE TO ... washer if it is torn or worn out. Water pressure MUST be 3/4 inch (1.9 cm) with threading for laundry hose connection. Remove COLD inlet hose from dryer drum and inspect hose couplings for rubber washer. Remove hose kit from COLD water supply and inspect for proper placement of rubber washers. Installation Instructions...
The faucet MUST be between 30 and 120 psi. Your water department can advise you of your dryer's water inlet. Turn off COLD water supply to clear any contaminants in the line. 4. RUBBER WASHER MUST BE PRESENT AND UNDAMAGED COLD INLET HOSE TO ... washer if it is torn or worn out. Water pressure MUST be 3/4 inch (1.9 cm) with threading for laundry hose connection. Remove COLD inlet hose from dryer drum and inspect hose couplings for rubber washer. Remove hose kit from COLD water supply and inspect for proper placement of rubber washers. Installation Instructions...
Installation Instructions (All Languages)
Page 16
...to the COLD water supply and snug it another 2/3 turn with pliers. 3. Tighten each connection of the dryer and snug it by hand; If there is not room to install the "Y" connector directly, thread the ...the "Y" connector and snug it by hand; then tighten it by hand. Turn on the back of the dryer inlet hose another 2/3 turn with pliers. If your installation has room for the COLD water supply to accept the...COLD WATER SUPPLY HOSE TO WASHER DIRECT CONNECTION OR WITH EXTENSION WATER INLET ON DRYER 16 Installation Instructions Water connection, con't (Steam Model only) 1.
...to the COLD water supply and snug it another 2/3 turn with pliers. 3. Tighten each connection of the dryer and snug it by hand; If there is not room to install the "Y" connector directly, thread the ...the "Y" connector and snug it by hand; then tighten it by hand. Turn on the back of the dryer inlet hose another 2/3 turn with pliers. If your installation has room for the COLD water supply to accept the...COLD WATER SUPPLY HOSE TO WASHER DIRECT CONNECTION OR WITH EXTENSION WATER INLET ON DRYER 16 Installation Instructions Water connection, con't (Steam Model only) 1.